EnOcean EDK 300 User manual
Getting Started V1.5
EDK 300
Getting Started
Page 2/24 © EnOcean GmbH
Important Notes
This information describes the type of component and shall not be considered as assured characteristics.
No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are
subject to change without notice. For the latest product specifications, refer to the EnOcean website:
http://www.enocean.com.
As far as patents or other rights of third parties are concerned, liability is only assumed for modules, not
for the described applications, processes and circuits. EnOcean does not assume responsibility for use of
modules described and limits its liability to the replacement of modules determined to be defective due
to workmanship. Devices or systems containing RF components must meet the essential requirements
of the local legal authorities. The modules must not be used in any relation with equipment that sup-
ports, directly or indirectly, human health or life or with applications that can result in danger for peo-
ple, animals or real value. Components of the modules are considered and should be disposed of as
hazardous waste. Local government regulations are to be observed.
Packing: Please use the recycling operators known to you.
This evaluation kit and its components are intended for use for evaluation, demonstration or
engineering development purposes only. It is not considered to be a finished end product fit for
consumer use. Persons handling this developer kit must have electronics expertise and observe good
engineering practice standards. As such, the goods being provided are not intended to be complete in
terms of required design, marketing, and/or manufacturing related protective considerations, including
product safety and environmental measures typically found in end products that incorporate such
electronic components or circuit board. EnOcean will not be reliable for consequences of any HW or SW
changes/modifications of the developer board(s) done by the developer. Before using EDK 300 please
consider country specific radio regulations and frequencies, e.g. R&TTE (EDK 300 = 868 MHz) for the
European Union or FCC (EDK 300C = 315 MHz) for US.
For users in Japan: This developer kit is not certified as confirming to technical regulations of radio
law of Japan. If you use this kit in Japan, you are required by Radio Law of Japan to follow the instruc-
tions below with respect to this product: Use this product in a shielded room or any other test facility as
defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28,
2006, based on sub-section 1.1 of article 6 of the “Rule for Enforcement of Radio Law of Japan”. Use
this kit only after you obtained the license of “Test Radio Station” as provided in Radio Law of Japan
with respect to this product, or use of this product only after you obtained the technical regulations
conformity certification as provided in radio law of Japan with respect to this product. Do not transfer
this product, unless you give the same notice above to the transferee. Please note that if you could not
follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Observe precautions! Electrostatic sensitive devices!
V1.5 05/2011 Page 3/24
Index
1Introduction ..............................................................................................4
2Line-powered applications with EVA 300 and TCM 3x0 ..............................5
2.1 Overview .................................................................................................5
2.2 Default Configuration ................................................................................6
2.3 Example: „1-Channel Relay Switch‟ (Mode 2)................................................7
2.4 Example: „1-Channel Dimmer‟ (Mode 4) ......................................................8
3Software Installation .................................................................................9
3.1 Updates...................................................................................................9
3.2 Overview .................................................................................................9
3.3 DolphinStudio Installation ........................................................................ 10
3.4 Check FW Version with DolphinStudio........................................................ 11
3.5 Update Module FW with DolphinStudio....................................................... 12
3.6 Configure STM 300 module ...................................................................... 13
3.7 DolphinView installation / presetting ......................................................... 14
3.8 Example „EVA 300 as Transceiver‟ (Mode 1) ............................................... 15
4Self-powered Applications with EVA 320 and STM 300 ............................17
4.1 Overview ............................................................................................... 17
4.2 Default Configuration .............................................................................. 18
4.3 Example: „Self-powered temperature sensor‟ ............................................. 19
4.4 Example: „Self-powered room operating panel‟ ........................................... 21
EDK 300
Getting Started
Page 4/24 © EnOcean GmbH
EDK 300
Developer‟s Kit
TCM 3x0
TCM 320
1Introduction
EDK 300 and EDK 300C are designed to support hardware
and software application development for following EnO-
cean modules:
868 MHz (EDK 300): TCM 3x0, STM 300
315 MHz (EDK 300C): TCM 3x0C, STM 300C
Content of EDK 300 Developer‟s Kit:
1x EVA 300 evaluation board for TCM 3x0
1x EVA 320 evaluation board for STM 300
1x TCM 300 on adapter board
1x STM 300 on adapter board
1x TCM 320
2x EOP 300 programmer
1x PTM 200 with test rocker
2x USB cable
1x Package leaflet with download links to
documentation and software tools
Additional developer kits are available for self-powered radio
nodes of the STM 3xy product family:
EDK 310 (Solar powered STM 3xy)
EDK 312 (Thermo powered STM 3xy)
V1.5 05/2011 Page 5/24
2Line-powered applications with EVA 300 and TCM 3x0
2.1 Overview
TCM 300 on
Adapter Board
EOP 300
Programmer EVA 300 Board
TCM 3x0
Mode config.
TCM 3x0
Repeater
config.
TCM 3x0
RSSI LEDs
Learn button
Learn Mode
Indicator (LMI) &
Channel LEDs
Clear button
LED: Power EOP
VCCUSB
LED: Power EVA
VCCIO
LED: Programmer
PROGACTIVE
Optional / not equipped
Power ON/OFF switch
EDK 300
Getting Started
Page 6/24 © EnOcean GmbH
2.2 Default Configuration
Power Management:
Power Switch (On/Off)
USB connector for external power supply
Mode and configuration jumper for TCM 300
Standard FW:
MODE 1: Serial bidirectional mode
MODE 2: 1 channel receiver mode
MODE 3: 4 channel receiver mode
MODE 4: Dimmer mode
2LEVEL: Select one/two-level repeater
REPEATER: Selector for repeater mode
Buttons:
Reset: reset the TCM3x0 module
Learn: add or delete ID from list
(standard TCM 3x0 FW)
Clear: clear whole ID list
(standard TCM 3x0 FW)
LEDs:
IO indicators
PWM (dimmer) or RSSI (signal strength)
Modul & extension slots:
TCM 300 adapter board connector
TCM 320 connector
TCM 300
USB power supply
optional / not equipped
V1.5 05/2011 Page 7/24
2.3 Example: ‘1-Channel Relay Switch’ (Mode 2)
1-channel relay mode to switch a light actuator. Telegrams from a learned PTM 2x0 push
button will change status of output ADIO7 (CH0).
1. Check jumper configuration of EVA 300 ac-
cording to the image on the right side, espe-
cially MODE2 jumper
2. Connect EVA 300 to delivered USB power
supply
3. Switch on EVA 300 board
4. Learn PTM 2x0 (switch) ID to TCM3x0:
- Press EVA 300 LEARN > 0.5s
(LMI LED will light, CH0 flash)
- Push PTM 2x0 to send learn telegram
- Wait until CH0 LED will flash
- Finish learn mode with LEARN button
> 0.5s
5. Switching PTM 2x0 will toggle CH0 LED (relay
pin)
Attention:
If you have changed TCM firmware: Load
EnOcean TCM 300 default firmware from CD
If you have changed mode settings:
Clear ID
- press CLEAR button > 2s
(LEDs “LMI” will light & “CH0” blink)
- press RESET (mode selection)
TCM 300
USB power supply
CH0
LMI
optional / not equipped
EDK 300
Getting Started
Page 8/24 © EnOcean GmbH
2.4 Example: ‘1-Channel Dimmer’ (Mode 4)
1-channel dimmer mode to dim a electrical actuator.
Telegrams from a learned push button will change
PWM output signal.
1. Check jumper configuration of EVA 300 accord
to the image on the right side, especially MODE4
& PWM
2. Connect EVA 300 to delivered USB power supply
3. Learn PTM 2x0 (switch) ID to TCM3x0:
- Press EVA300 LEARN > 0.5s
(LMI & CH2 LED will light, CH0 flash)
- Push PTM 2x0 to send learn telegram
- Wait until CH0 LED will flash
- Finish learn mode with LEARN button > 0.5s
4. PTM 2x0:
- hold O-side long time, WM signal will drop
from high to low
- hold I-side long time, PWM signal will rise from
low to high
- press 1-side short time, TCM3x0 will switch on
with last PWM value
- press 0-side short time, TCM3x0 will switch off
Attention:
If you have changed FW: Load EnOcean TCM 300 default firmware from CD
If you have changed mode settings: Clear ID
- press CLEAR button > 2s (LEDs “LMI” will light & “CH0” blink)
- press RESET (mode selection)
TCM 300
USB power supply
LMI
CH1
CH2
optional / not equipped
V1.5 05/2011 Page 9/24
3Software Installation
3.1 Updates
Please register for your personal account and check following
website for updates: http://www.enocean.com/en/download/
3.2 Overview
DolphinAPI (for details see EDK 300 user manual)
Operating system for self-powered applications
Source code samples in C-Code for switching, dimming, etc.
Comprehensive software libraries (wireless communication,
energy management, etc.)
DolphinStudio
Windows application which supports the whole firmware
development process (chip configuration, programming, module updating)
DolphinView
Visualize properites of EnOcean radio nodes
Receives, sends and analyses radio telegrams according to the EnOcean standard
Get detailed information e.g. subtelegram timing and signal strength
Content of telegrams can be analyzed online and logged with time stamp
Supports remote management features like ping, query and remote learn
PC requirements
- Microsoft Windows XP SP3 or Windows 7
- Microsoft .NET Framework 3.5 SP1
- 1.5 GHz CPU, 1 GB RAM, 0,3 GB Disc Space
- Graphics: min. 1024x768 with DirectX 9 support
EDK 300
Getting Started
Page 10/24 © EnOcean GmbH
3.3 DolphinStudio Installation
1. Launch DolphinStudio setup pro-
gram and follow instructions
2. Connect EOP300 to PC via USB
cable
3. Press “Options” button within menu
bar
4. “Options” window will appear, press
“Refresh” to recognize EOP 300
programmer
5. Programmer settings/firmware will
be update if necessary
Attention:
If you have installed a previous DolphinStudio version, it is recommended to uninstall
older version
If you have already installed older FTDI USB driver, it is recommended to remove
previous and install latest FTDI driver by cross marking installation menu at the end
of DolphinSetup
3
4
Table of contents
Popular Microcontroller manuals by other brands
AMS
AMS AS7261 Demo Kit user guide
Novatek
Novatek NT6861 manual
Espressif Systems
Espressif Systems ESP8266 SDK AT Instruction Set
Nuvoton
Nuvoton ISD61S00 ChipCorder Design guide
STMicrolectronics
STMicrolectronics ST7 Assembler Linker user manual
Texas Instruments
Texas Instruments Chipcon CC2420DK user manual
Texas Instruments
Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual
CYPRES
CYPRES CY14NVSRAMKIT-001 user guide
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM user guide
Espressif Systems
Espressif Systems ESP8266EX Programming guide
Abov
Abov AC33M8128L user manual
Laird
Laird BL654PA user guide