ENGINDOT GSH01B User manual
User Manual
Gas Pressure Washer
Model：GSH01B
ID:QX2121-65F32
HIGH PRESSURE WASHER OPERATOR MANUAL
Please read and comply with
these original instructions prior to
the initial operation of your appli-
ance and store them for later use
or subsequent owners.
Contents
Model Overview
Safety Instructions
Assembly Instructions
Preparation
Operating Instruction
Using the Accessories
Working with Detergents
Taking a Break
Shutting Down & Clean Up
Winterizing & Long Term
Storage
Maintenance Instructions
Cleaning Tips
Troubleshooting
EN-2
EN-3
EN-6
EN-7
EN-8
EN-9
EN-10
EN-10
EN-11
EN-11
EN-11
EN-12
EN-14
Specifications
Operating Pressure
Water Volume
Engine
Fuel Type
Fuel Tank Size
Engine Oil Type
Engine Oil Capacity
Model Numbe
3200 PSI
540 l/h
Rato 209cc
R210-S
2.6L
SAE 10W-30
GSH01B
1
0.6L
1
2
3
4
5
6
7
8
AIR CLEANER
FUELTANK
FUEL TANKCAP
MUFFLER
HAND CORD
ENGINE STWICH
OIL DISTICK
1. Spray Gun
3. Pressure Hose
Thermal Relieve
Valve
2. Nozzles
7.Detergent Tank
Model Overview
GSH01B
2
5. Pump
4. Engine
6.Wheels
8. Rubber Foot
Pump Inlet
Pump Outlet
Hazard Levels
Safety Instructions
Indicates “an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.”
Indicates “a potentially hazardous
situation which, if not avoided, could
result in death or injury.”
Indicates “a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury or in
property damage incidents.”
When using this product, basic
precautions should always be
followed, including the following:
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
Read the operating instructions of
the engine manufacturer before
start-up and follow the safety
instructions carefully.
Read all instructions before using
product.
To reduce the risk of injury, close
supervision is necessary when the
product is used near children.
Know how to stop the product and
bleed pressures quickly. Be
thoroughly familiar with the
controls.
Stay alert - watch what you are
doing.
Do not operate when fatigued or
under the influence of alcohol or
drugs.
Keep operating area clear of all
persons.
Do not overreach or stand on
unstable support. Keep good
footing and balance at all times.
Wear safety goggles and ear
protection.
Follow the maintenance instruc-
tions specified in the manual.
To avoid risks, all repairs and
replacement of spare parts should
only be carried out by trained
personnel.
Tire pressure should not exceed
max. 25 psi.
Risk of injection or injury – Do not
direct discharge stream at
persons.
High pressure jets can be danger-
ous if misused. The jet must not
be directed at persons, animals,
electrical devices, or the unit itself.
Do not spray electrical connec-
tions, electrical outlets or fixtures.
Do not use acids, solvents, or any
alkaline or flammable material in
this product. These products can
cause physical injuries to the
operator and irreversible damage
to the machine.
3
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
▬
Water Supply
(Cold Water Only)
Gun kicks back – Hold with both hands
The trigger gun safety lock prevents
the trigger from accidentally being
engaged. This safety feature must be
engaged when replacing nozzles or
not in use.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Operation of this equipment may
create sparks that can start fires
around dry vegetation. A spark arrestor
may be required. Operator should
contact local fire agencies for laws or
regulations.
Risk of asphyxiation – Use this product
only in a well ventilated area. Do not
operate indoors or in any confined
area.
Operate and fuel machine in a well
ventilated area, free of devices featur-
ing an open pilot or flame such as
boilers, water heaters, etc.
Risk of fire/explosion – Do not add fuel
when the machine is operating or still
hot.
Risk of fire/explosion -Operate only
where open flame or torch is permitted.
Do not spray flammable liquids.
Do not operate if fuel has been
spilled. Instead, move machine to
different location and avoid creat-
ing sparks.
This machine has hot surfaces
which can cause burns. Operate
in a safe environment and away
from children.
Do not touch hot surfaces or allow
accessories to contact hot surfac-
es.
Do not leave machine running
unattended.
Avoid tipping machine on its side.
When connecting to water supply
mains, local regulations of your
municipal water company must be
observed. In some areas connect-
ing directly to public drinking water
supply may require a back flow
prevention device. This is to
ensure that there is no feedback
of chemicals into the water supply.
Use a water filter to avoid potential
damage from dirt in the water
supply.
Garden hose must be at least 5/8
inch diameter.
Flow rate of water supply must not
fall below 2.6 GPM(gallons per
minute)
Flow rate can be determined by
running the water for one minute
into an empty 5-gallon container.
The water supply temperature
must not exceed 122°F/50°C.
Never use the pressure washer to
4
▬
▬
draw in water contaminated with
solvents, e.g. paint thinners, gasoline,
oil, etc.
Always prevent debris from being
drawn into the unit by using a clean
water source. Use additional water
filter.
Do not operate pressure washer
without the water turned on.
Assembly Instructions
Part List
A - Main Frame C - Gun Hook
D - Knobs & Bolts E – Pressure Hose
B - Handle
5
F - Spray Gun &Wand
Assembling
G - Wheels
Parts not shown:
1 - Manual
2 - Nozzle Cleaner
3 - Spark Plug Wrench
4 - O-Ring Set
(2 for pressure hose, 1 for spray gun)
►
►
6
H – Flat Gasket
I – Elastic Gasket
J – Screw
K – Screw Driver
5 - Funnel For Adding Engine Oil
Wheel
> Squeeze the locking pin (G2) and
insert the wheel axle (G1) into the hole
of the wheel (step 1).
> Squeeze the locking pin and insert the wheel
axle into the wheel support (G5)(step 2).
Ensure the locking pin snaps in the locking
hole (G3) properly.
> Put the wheel hubcap (G4) onto the wheel.
(step 3). Ensure it snaps in place properly.
> Repeat with the other wheel.
►
1.
2. 3.
G4
G1
G5G3 G2
G
Handle
> Align the holes and attach the upper
handle bar (B) onto the lower handle
bar (A).
> Secure the connection with bolts (D2)
and knobs (D1). Ensure the
bolts (D2) are engaged into the
square hole properly.
B
D1 D1
D2
AA
> Secure the spray gun holder (C)
onto the upper hand bar (B) with
flat gasket (H), elastic gasket (I)
and screw (J) using the provided
screwdriver (K).
Gun Holder
B
C
H I J
L-Water Inlet Filter
►
►
►
Always use SAE 10W-30 oil.
Oil crankcase capacity: 0.6L.
Reposition the oil gauge dipstick and
tighten it by turning clockwise.
Engine oil should be changed after the
first 5 hours, then every 50 hours.
Make sure there is enough fuel in the
fuel tank before operating.This is a
4-cycle engine and does not require a
gas/oil mixture. There is a separate
reservoir for gas and a separate reser-
voir for oil.
If it is necessary to add fuel, first make
sure the engine is OFF, and then
►
►
►
Preparation
Oil Level
Fuel Level
Engine shipped without oil in crank-
case. Before starting engine, fill with
oil with funnel provided..
Do not over-fill. Do not run the
engine with a high or low oil level as
this can cause engine damage.
Turn the oil gauge dipstick counter
clockwise; remove it and clean it with a
clean cloth.
Fully reinsert the oil gauge dipstick and
pull it out to check the oil level.
If the oil level is halfway up the dipstick
or below, refill with SAE
10W -30 oil through the dipstick hole
until the oil level reaches 3/4 up the
dipstick or until it reaches the bottom
lip of the dipstick hole as shown.
7
OIL DISTICK
►
►
►
►
►
►
Operating Instructions
Air Filter
remove the fuel cap by turning it count-
er clockwise.
When refueling, make sure the fuel
filter is in place and keep in mind all
safety precautions.
Use clean unleaded gasoline with a
minimum of 87 octane. DO NOT use
old gas. DO NOT mix oil with gasoline.
Fuel tank capacity: .2.6L
Press the two clips on the top of the air
filter cover to remove the cover.
Starting Procedure:
Connect pressure hose onto pump
outlet (step 3).
Connect spray gun and
pressure hose.
8
►
3.
1.
►
Connect garden hose onto pump
intlet (step 2).
►
Spark Plug
2.
►Insert the water inlet filter(L) into
pump intlet (step 1).
►Open water source.
►
1.
2.
3.
4.
5.
NOTE: If unable to start the engine, repeat
the above operation one or two times.
Cleaning Procedure:
►
Using the Accessories
Quick Connect Nozzles
Start the Engine
Turn the engine switch to "ON"
position.
Pull the choke lever towards the
CLOSE position
Pull trigger on spray gun to release
pressure.
Locate recoil cord and pull slowly until
resistance is felt. At this point, pull
rapidly to start engine.
Pull the choke lever towards the OPEN
position
Position the tip of the wand 6-8”
(15-20 cm) away from the surface to
clean at a 45°angle.
The color-coded quick connect
nozzles provide a wide array of spray
widths from 0° to 40° and are easily
accessible when placed in the conve-
nient nozzle holder.
0° spray angle = Red nozzle
For particularly stubborn accumulation
of grime. Not recommended for soft
materials like sidings, decks, painted
surfaces, cars.
15° spray angle = Yellow nozzle For
dirt accumulation over a surface.
9
ON/OFF
SWITCH
CHOKE LEVER
CHOKE LEVER
Table of contents
Other ENGINDOT Pressure Washer manuals
