Endress+Hauser iTEMP TMT82 Technical specifications
Brief Operating Instructions
iTEMP® TMT82
Dual-Input Temperature Head Transmitter
These instructions are Brief Operating Instructions.
For detailed information, refer to the Operating Instructions and other
documentation on the CD-ROM provided or visit "www.endress.com/
deviceviewer".
These Brief Operating Instructions do not act as a substitute for the Operating
Instructions included in the scope of delivery.
The complete device documentation comprises:
• These Brief Operating Instructions
•A CD-ROM with PDF files of:
– Operating Instructions
– Approval and safety certificates
– Further device specific information.
KA01095T/09/EN/13.10
71124515
Table of contents iTEMP® TMT82
2 Endress+Hauser
Table of contents
1 Important document information ............................... 2
1.1 About this document ............................................ 2
1.2 Document conventions ........................................... 3
2 Basic safety instructions ...................................... 4
2.1 Requirements for the personnel ....................................... 4
2.2 Designated use ............................................... 4
2.3 Operational safety .............................................. 4
3 Identification ............................................. 5
3.1 Device designation ............................................. 5
3.2 Scope of delivery .............................................. 6
3.3 Certificates and approvals .......................................... 6
4 Installation instructions ...................................... 6
4.1 Incoming acceptance, transport, storage ................................... 6
4.2 Installation conditions ............................................ 7
4.3 Installation instructions ........................................... 7
4.4 Post-installation check ........................................... 10
5 Wiring ................................................. 10
5.1 Quick wiring guide ............................................. 11
5.2 Connecting the sensor cables ........................................ 12
5.3 Connecting the power supply and signal cables ............................... 13
5.4 Shielding and grounding .......................................... 14
5.5 Post-connection check ........................................... 15
6 Operating options ......................................... 16
6.1 Measured value display and operating elements ............................... 16
6.2 Configuration of the head transmitter via HART® protocol .......................... 18
7 Commissioning ........................................... 19
7.1 Function check .............................................. 19
7.2 Switching on the head transmitter ..................................... 19
7.3 Enabling configuration ........................................... 19
1 Important document information
1.1 About this document
1.1.1 Document function
These Brief Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and storage, to
mounting, connection and operation.
1.1.2 Safety Instructions (XA)
When using in hazardous areas, the national safety requirements must be met. Separate Ex
documentation is contained in these Operating Instructions for measurement systems that are
iTEMP® TMT82 Important document information
Endress+Hauser 3
to mounted in hazardous areas. Strict compliance with the installation instructions, ratings and
safety instructions as listed in this supplementary documentation is mandatory. Ensure you are
using the correct Ex documentation for the relevant Ex-approved device. The number of the
related Ex documentation (XA...) is indicated on the nameplate. You can use this Ex
documentation if the two numbers (i.e. in the Ex documentation and on the nameplate) are
identical.
1.2 Document conventions
1.2.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
CAUTION
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
NOTICE
A0011192-EN
NOTE!
This symbol contains information on procedures and other facts which do not result
in personal injury.
1.2.2 Symbols and notation for certain types of information
Symbol Meaning
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
1., 2., 3. Series of steps
Basic safety instructions iTEMP® TMT82
4 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the
following requirements:
►Trained, qualified specialists must have a relevant qualification for this specific function and
task
►Are authorized by the plant owner/operator
►Are familiar with federal/national regulations
►Before beginning work, the specialist staff must have read and understood the instructions in
the Operating Instructions and supplementary documentation as well as in the certificates
(depending on the application)
►Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
►Being instructed and authorized according to the requirements of the task by the facility's
owner-operator
►Following the instructions in these Operating Instructions
2.2 Designated use
The device is a universal and user-configurable temperature head transmitter with either one or
two sensor inputs for a resistance thermometer (RTD), thermcouples (TC) or resistance and
voltage transmitters. The device is designed for mounting in a flat-face terminal head as per DIN
43729. Installation on a DIN rail with the optional available DIN rail clip is also possible.
The manufacturer is not liable for damage caused by improper or non-designated use.
2.3 Operational safety
►Operate the device in proper technical condition and fail-safe condition only.
►The operator is responsible for interference-free operation of the device.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous
area (e.g. explosion protection):
►Based on the technical data on the nameplate, check whether the ordered device is permitted
for the intended use in the hazardous area. The nameplate can be found on the side of the
transmitter housing.
►Observe the specifications in the separate supplementary documentation that is an integral
part of these Instructions.
Electromagnetic compatibility
The measuring system complies with the general safety requirements in accordance with EN
61010, the EMC requirements of IEC/EN 61326 and NAMUR Recommendation NE 21 and
NE 89.
iTEMP® TMT82 Identification
Endress+Hauser 5
NOTICE
►The unit must only be powered by a power supply that operates using an IEC 61010-1
compliant energy limited circuit, "SELV or Class 2 circuit".
3 Identification
3.1 Device designation
The following options are available for identification of the device:
• Nameplate specifications
•Enter the serial number from the nameplate in W@M Device Viewer (www.endress.com/
deviceviewer): All information about the device and an overview of the technical
documentation supplied with the device is displayed.
3.1.1 Nameplate
The right device?
Compare and check the data on the nameplate of the device against the requirements of the
measuring point:
123
45
11-42V 012345678910
xx.yy.zz
TMT82- XXXXX/XX
iTEMP®
Made in Germany 2011
D-87484 Nesselwang
Ser.no.:
FW:
Input:
12345678ABCDEFGH
12345678ABCDEFGH
Current consum.: 23,6 mA Dev.Rev: 1
Ext. ord. cd.:
XXXXXXXXXXXXX#
II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C
II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C
EH 08.001X
Install per XA00102R/09/a3/xx.xx
6
0044
A0014561
å 1 Nameplate of the head transmitter (example, Ex version)
1 Power supply, current consumption and extended order code
2 Serial number, device revision and firmware version
3 Approvals with symbols
4 2 lines for the TAG name
5 Approval in hazardous area with number of the relevant Ex documentation (XA...)
6 Order code
Installation instructions iTEMP® TMT82
6 Endress+Hauser
3.2 Scope of delivery
The scope of delivery of the device comprises:
•Temperature Head Transmitter
• Securing material
• Hard copy of multi-language Brief Operating Instructions
• Operating Instructions and additional documentation on CD-ROM
• Additional documentation for devices which are suitable for use in the hazardous area (0
1), such as Safety Instructions (XA), Control or Installation Drawings (ZD).
3.3 Certificates and approvals
The device left the factory in a safe operating condition. The device complies with the standards
EN 61 010-1 "Protection Measures for Electrical Equipment for Measurement, Control,
Regulation and Laboratory Procedures" and with the EMC requirements of IEC/EN 61326.
3.3.1 CE mark, declaration of conformity
The device therefore meets the legal requirements of the EC guidelines. The manufacturer
confirms a positive completion of all tests by fitting the unit with a CE mark.
3.3.2 HART® protocol certification
The temperature transmitter is registered by HART® Communication. The device meets the
requirements of the HART Communication Protocol Specifications, April 2001, Revision 6.0.
4 Installation instructions
4.1 Incoming acceptance, transport, storage
4.1.1 Incoming acceptance
• Is the packaging or content damaged?
• Is the delivery complete and is anything missing? Check the scope of delivery against your
order.
4.1.2 Transport and storage
• Pack the device in such a way as to protect it reliably against impact for storage (and
transportation). The original packaging provides optimum protection.
• The permitted storage temperature is -40 to +100 °C (-40 to 212 °F).
iTEMP® TMT82 Installation instructions
Endress+Hauser 7
4.2 Installation conditions
4.2.1 Dimensions
24.1 (0.95”)
33 (1.3”)
Ø44 (1.73”)
Ø7 (0.28”)
Ø5 (0.2”)
B
C
A
A0007301
å 2 Version with screw terminals. Dimensions in mm (in)
A Spring travel L ≥ 5 mm (not for US - M4 securing screws)
B Securing elements for attachable measured value display
C Interface for measured value display contact
The same dimensions apply to the version with spring terminals apart from the housing
height H = 28.1 mm (1.11").
4.2.2 Installation point
• In the terminal head as per DIN 43 729, flat face, direct mounting on insert with cable entry,
middle hole 7 mm (0.28").
• Separate from the process in the field housing.
• With DIN rail clip on top-hat rail as per IEC 60715.
4.2.3 Important ambient conditions
Ambient temperature range: -40 to +85°C (-40 to +185 °F).
Condensation permitted as per IEC 60068-2-33; max. rel. humidity: 95%.
Climate class in accordance with IEC 60654-1, Class C.
IP 20 ingress protection, depends on the terminal head or field housing in its installed state.
NOTICE
►When using in the hazardous area, the limit values of the certificates and approvals must be
observed (see Safety Instructions XA or CD).
4.3 Installation instructions
A Phillips head screwdriver is required to mount the head transmitter.
Installation instructions iTEMP® TMT82
8 Endress+Hauser
NOTICE
Do not overtighten the mounting screws as this could damage the head transmitter.
►Maximum torque = 1 Nm (¾ pound-feet).
4.3.1 Mounting
1
2
3
4
5
6
7
9
8
1 2 3 4 5
1 2 3 4 5
Item A Item B
Item C
A0014269-EN
å 3 Head transmitter mounting (three versions)
Procedure mounting in a terminal head, item A:
1. Open the terminal head cover (8).
2. Guide the connection wires (4) of the insert (3) through the center hole in the head
transmitter (5).
3. Fit the mounting springs (6) on the mounting screws (7).
4. Guide the mounting screws (7) through the side boreholes of the head transmitter and the
insert (3). Then fix both mounting screws with the snap rings (2).
5. Then tighten the head transmitter (5) along with the insert (3) in the terminal head.
6. After wiring, (® ä 10) close the terminal head cover (8) back on tight.
Procedure mounting in a field housing, item B:
1. Open the cover (1) of the field housing (5).
iTEMP® TMT82 Installation instructions
Endress+Hauser 9
2. Fit the mounting springs on the mounting screws (2) and guide the screws through the
side boreholes of the head transmitter (3). Then fix both mounting screws with the snap
rings (4).
3. Screw the head transmitter to the field housing.
4. After wiring, (® ä 10) screw the field housing cover (1) back on.
Procedure mounting on top-hat rail, item C:
1. Press the DIN rail clip (4) onto the top-hat rail (5) until it engages with a click.
2. Fit the mounting springs on the mounting screws (1) and guide the screws through the
side boreholes of the head transmitter (2). Then fix both mounting screws with the snap
rings (3).
3. Screw the head transmitter (2) onto the DIN rail clip (4).
4.3.2 Mounting typical of North America
123 4 5
6
5
6
A0008520
å 4 Head transmitter mounting
Thermometer design with thermocouples or RTD sensors and head transmitter:
1. Fit the thermowell (1) on the process pipe or the container wall. Secure the thermowell
according to the instructions before the process pressure is applied.
2. Fit the necessary neck tube nipples and adapter (3) on the thermowell.
3. Make sure sealing rings are installed if such rings are needed for harsh environmental
conditions or special regulations.
4. Guide the mounting screws (6) through the lateral bores of the head transmitter (7).
5. Position the head transmitter (5) in the terminal head (4) in such a way that the bus cable
(terminals 1 and 2) point to the cable entry.
Wiring iTEMP® TMT82
10 Endress+Hauser
6. Using a screwdriver, screw down the head transmitter (5) in the terminal head (4).
7. Guide the connection wires of the insert (3) through the lower cable entry of the terminal
head (4) and through the middle hole in the head transmitter (5). Wire the connection
wires and transmitter (® ä 11) with one another.
8. Screw the terminal head (4), with the integrated and wired head transmitter, onto the
ready-mounted nipple and adapter (3).
NOTICE
The terminal head cover must be secured properly to meet the requirements for
explosion protection.
►After wiring, securely screw the terminal head cover back on.
4.4 Post-installation check
After installing the device, always run the following final checks:
Device condition and specifications Notes
Is the device undamaged (visual inspection)? -
Do the ambient conditions match the device specification (e.g. ambient temperature, measuring
range, etc.)?
(® ä 7)
5 Wiring
!CAUTION
►Switch off power supply before installing or connecting the device. Failure to observe this
may result in destruction of parts of the electronics.
►When installing Ex-approved devices in a hazardous area, please take special note of the
instructions and connection schematics in the respective Ex documentation added to these
Operating Instructions. The local Endress+Hauser representative is available for assistance if
required.
►Do not occupy the display connection. An incorrect connection can destroy the electronics.
For wiring a mounted head transmitter, proceed as follows:
1. Open the cable gland and the housing cover on the terminal head or the field housing.
2. Feed the cables through the opening in the cable gland.
3. Connect the cables as shown in (® ä 11). If the head transmitter is fitted with spring
terminals, pay particular attention to the information in the "Connecting to spring
terminals" section .
4. Retighten the cable gland and close the housing cover.
In order to avoid connection errors always take note of the hints given in the section connection
check!
Other manuals for iTEMP TMT82
7
Table of contents
Other Endress+Hauser Transmitter manuals
Endress+Hauser
Endress+Hauser iTEMP TMT84 Technical specifications
Endress+Hauser
Endress+Hauser iTEMP TMT162 Technical specifications
Endress+Hauser
Endress+Hauser Memograph CVM40 User manual
Endress+Hauser
Endress+Hauser Liquisys M COM 223 User manual
Endress+Hauser
Endress+Hauser AT5000 User manual
Endress+Hauser
Endress+Hauser FHX50 User manual
Endress+Hauser
Endress+Hauser iTEMP PA TMT184 User manual
Endress+Hauser
Endress+Hauser Heat Technical specifications
Endress+Hauser
Endress+Hauser Levelflex FMP 232 Specification sheet
Endress+Hauser
Endress+Hauser Liquisys M COM 223 User manual
Endress+Hauser
Endress+Hauser iTEMP TMT182 User manual
Endress+Hauser
Endress+Hauser CM14 User manual
Endress+Hauser
Endress+Hauser Liquisys M CPM 223 User manual
Endress+Hauser
Endress+Hauser Liquisys M CLM223 User manual
Endress+Hauser
Endress+Hauser cerabar M PMP 46 Manual
Endress+Hauser
Endress+Hauser Proline 500 digital PROFIBUS DP Technical specifications
Endress+Hauser
Endress+Hauser Deltabar S FMD76 User manual
Endress+Hauser
Endress+Hauser iTEMP TMT82 Technical specifications
Endress+Hauser
Endress+Hauser Commubox FXA291 User manual
Endress+Hauser
Endress+Hauser Proline Prosonic Flow 93 User manual
Popular Transmitter manuals by other brands
Dejero
Dejero EnGo 3x manual
Rosemount
Rosemount 4600 Reference manual
Speaka Professional
Speaka Professional 2342740 operating instructions
trubomat
trubomat GAB 1000 instruction manual
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 instructions
Rondish
Rondish UT-11 quick start guide
