Emerson Rosemount 705 User manual

Quick Start Guide

00825-0200-4705, Rev AA

August 2014

Rosemount 705 Wireless Totalizing

Transmitter

An installation-ready solution that provides simple and easy connection to a

pulse source

Measure average flow and totalized volume

Flow and volume are continuously measured between wireless updates

Self-organizing network delivers information rich data with >99% data

reliability totalized volume

00825-0200-4705_RevAA.fm Page 1 Monday, August 4, 2014 3:48 PM

August 2014

Quick Start Guide

Required equipment

Measuring tape

Standard tools (e.g. screwdriver, wrench, pliers)

Anti-seize paste or PTFE tape (for threaded connection)

AMS®Wireless Configurator version 12.0 or later, or Field Communicator

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,

national and international standards, codes, and practices.

Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.

Electrical shock can result in death or serious injury.

Ground device to prevent electrostatic charge build-up.

Care must be taken during transportation of power module to prevent electrostatic charge

build-up.

Device must be installed to ensure a minimum antenna separation distance of 8 in. (20 cm)

from all persons.

Process leaks could result in death or serious injury.

Handle the transmitter carefully.

Failure to follow safe installation guidelines could result in death or serious injury.

Only qualified personnel should install the equipment.

NOTICE

This guide provides basic guidelines for the Rosemount 705. It does not provide instructions for

detailed configuration, diagnostics, maintenance, service, troubleshooting, or installations.

Refer to the Rosemount 705 Reference Manual (document number 00809-0200-4705) for

more instruction. This guide and the manual are available electronically on

www.emersonprocess.com.

Shipping considerations for wireless products:

The unit was shipped without the power module installed. Remove the power module prior to

shipping the unit.

Each power module contains two “C” size primary lithium batteries. Primary lithium batteries

are regulated in transportation by the U.S. Department of Transportation, and are also covered

by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the

responsibility of the shipper to ensure compliance with these or any other local requirements.

Consult current regulations and requirements before shipping.

00825-0200-4705_RevAA.fm Page 2 Monday, August 4, 2014 3:48 PM

Quick Start Guide

August 2014

Step 1: Install pulse output device

Step 2: Seal and protect threads

Use anti-seize paste or PTFE tape according to your site procedures.

Conduit entries

Upon installation, ensure each conduit entry is either sealed with a conduit plug

with appropriate thread sealant, or has an installed conduit fitting or cable gland

with appropriate thread sealant. Note the conduit entries on the Rosemount 705

Totalizer are threaded 1/2-14 NPT.

A. Conduit entry

Step 3: Mount 705 on pulse input device

General considerations

Physical installation

The Rosemount 705 Totalizer and all other wireless devices should not be set up

until after the Smart Wireless Gateway has been installed and is functioning

properly.

The transmitter can be installed in one of two configurations:

Direct Mount, where the pulse output device is connected directly to the

transmitter housing’s conduit entry

Remote Mount, where the pulse output device is mounted separate from the

transmitter housing, then connected to the transmitter via conduit

Choose the installation sequence that corresponds to the mounting

configuration.

00825-0200-4705_RevAA.fm Page 3 Monday, August 4, 2014 3:48 PM

August 2014

Quick Start Guide

Direct mount

Note

Direct mount installation should not be employed when using tubing and connectors such as

Swagelok®fittings.

1. Install the pulse output device according to standard installation practices

making sure to use thread sealant on all connections.

2. Attach the pulse output device wiring to the terminals as indicated on the

wiring diagram (reference figures on page 15 through page 30).

3. Attach the transmitter housing to the pulse output device using the threaded

conduit entry.

Note

Wireless devices should be powered up with the proper join key and network ID in order of

proximity from the Smart Wireless Gateway. Beginning with the closest device to the Smart

Wireless Gateway will result in a faster network installation.

4. Connect the Black Power Module.

5. Close the housing cover and tighten to safety specification. Always ensure a

proper seal so that metal touches metal, but do not over tighten.

6. Position the antenna so it is vertical, either straight up or straight down.

00825-0200-4705_RevAA.fm Page 4 Monday, August 4, 2014 3:48 PM

Quick Start Guide

August 2014

a. The antenna should be approximately 3-ft. (0.91 m) from any large

structures or buildings, to allow clear communication to other devices.

Remote mount

1. Install the pulse output device according to standard installation practices

making sure to use thread sealant on all connections.

2. Run wiring (and conduit if necessary) from the pulse output to the Rosemount

705 Totalizer.

3. Pull the wiring through the threaded conduit entry of the transmitter.

4. Attach the wiring to the terminals as indicated on the wiring diagram.

Note

Wireless devices should be powered up with the proper join key and network ID in order of

proximity from the Smart Wireless Gateway. Beginning with the closest device to the Gateway will

result in a faster network installation.

5. Connect the Black Power Module.

Possible antenna rotation shown.

Antenna rotation allows for best

installation practices in any

configuration.

00825-0200-4705_RevAA.fm Page 5 Monday, August 4, 2014 3:48 PM

August 2014

Quick Start Guide

6. Close the housing cover and tighten to safety specification. Always ensure a

proper seal so that metal touches metal, but do not over tighten.

7. Position the antenna vertically and straight up.

a. The antenna should be approximately 3-ft. (0.91 m) from any large

structures or buildings, to allow clear communication to other devices.

00825-0200-4705_RevAA.fm Page 6 Monday, August 4, 2014 3:48 PM

Quick Start Guide

August 2014

Remote antenna (optional)

The remote antenna option provides flexibility for mounting the Rosemount 705

Totalizer based on wireless connectivity, lightning protection, and current work

practices.

The remote mount antenna kit includes coaxial sealant for the cable connections

for the lightning arrestor and antenna.

Find a location where the remote antenna has optimal wireless performance.

Ideally this will be 15-25 ft. (4.6 - 7.6 m) above the ground or 6 ft. (2 m) above

obstructions or major infrastructure. To install the remote antenna, use one of

the following procedures. The WN option is 25 ft. (7.6 m) and the WJ option is 10

ft. (3 m).

WN/WJ remote antenna option

1. Mount the antenna on a 1.5-2 in. pipe mast using the supplied mounting

equipment.

2. Connect the lightning arrestor directly to the top of the Rosemount 705

Totalizer.

3. Install the grounding lug, lock washer, and nut on top of lightning arrestor.

4. Connect the antenna to the lightning arrestor using the supplied LMR-400

coaxial cable ensuring the drip loop is not closer than 1 ft. (0.3 m) from the

lightning arrestor.

5. Use the coaxial sealant to seal each connection between the wireless field

device, lightning arrestor, cable, and antenna.

6. Ensure the mounting mast and lightning arrestor are grounded according to

local/national electrical code.

Note

Any spare lengths of coaxial cable should be placed in 12 in. (0.3 m) coils.

When installing remote mount antennas for the transmitter, always use established safety

procedures to avoid falling or contact with high-power electrical lines.

Install remote antenna components for the transmitter in compliance with local and national

electrical codes and use best practices for lightning protection.

Before installing, consult with the local area electrical inspector, electrical officer, and work

area supervisor.

The transmitter remote antenna option is specifically engineered to provide installation

flexibility while optimizing wireless performance and local spectrum approvals. To maintain

wireless performance and avoid non-compliance with spectrum regulations, do not change

the length of cable or the antenna type.

If the supplied remote mount antenna kit is not installed per these instructions, Emerson

Process Management is not responsible for wireless performance or non-compliance with

spectrum regulations.

00825-0200-4705_RevAA.fm Page 7 Monday, August 4, 2014 3:48 PM

August 2014

Quick Start Guide

Figure 1. Rosemount 705 Totalizer with Remote Antenna

Note

Weather proofing is required! The remote mount antenna kit includes coaxial sealant for weather

proofing the cable connections for the lightning arrestor, antenna, and Rosemount 705 Totalizer.

Coaxial sealant must be applied to guarantee performance of the wireless field network. See

Figure 2 for details on how to apply coaxial sealant.

Figure 2. Applying Coaxial Sealant to Cable Connections

00825-0200-4705_RevAA.fm Page 8 Monday, August 4, 2014 3:48 PM

Quick Start Guide

August 2014

Step 4: Insert black power module

Power up sequence

The Smart Wireless Gateway should be installed and functioning properly before

any wireless field devices are powered. Install the Black Power Module,

SmartPower™Solutions model number 701PBKKF (part number

00753-9220-0001) into the transmitter to power the device.

Wireless devices should be powered up in order of proximity from the Gateway,

beginning with the closest device, then working outward from the Gateway. This

results in a faster network installation. Enable Active Advertising on the Gateway

to ensure new devices are able to join the network faster. For more information

see the Smart Wireless Gateway Manual (document number 00809-0200-4420).

Step 5: Connect to device

A. Field Communicator

B. Communication terminals

C. HART®Modem

D. AMS Device Manager

AMS Wireless Configurator

1. Start AMS Wireless Configurator.

2. In the View menu, select Device Connection View.

3. Double click on the device under the HART modem.

123

456

00825-0200-4705_RevAA.fm Page 9 Monday, August 4, 2014 3:48 PM

August 2014

Quick Start Guide

Field Communicator

1. Turn on the Field Communicator.

2. Tap the HART symbol on the main menu.

The Field Communicator now connects to the device.

Field Communicator connections

The power module needs to be installed before the Field Communicator can

interface with the transmitter. This transmitter uses the Black Power Module;

order model number 701PBKKF.

Step 6: Configure device using Guided Setup

a. Go to Configure > Guided Setup > Initial Setup.

b. Select Basic Setup and follow the instructions.

c. Select Verify operation to check your flow measurement.

d. Consider optional setup, such as Update Rate and Device Display.

Step 7: Join device to network

a. Go to Overview > Shortcuts.

b. Select Configure Update Rate and follow the instructions.

c. Obtain Network ID and Join Key for the wireless network (available in wireless

gateway).

d. Select Join Device to Network and follow the instructions.

00825-0200-4705_RevAA.fm Page 10 Monday, August 4, 2014 3:48 PM

Other manuals for Rosemount 705

Table of contents

Other Emerson Transmitter manuals

Emerson

Emerson Rosemount 3051 User manual

Emerson

Emerson Micro Motion 5700 User manual

Emerson

Emerson Rosemount CX1100 User manual

Emerson

Emerson Rosemount 2090 Configuration guide

Emerson

Emerson 6081-P User manual

Emerson

Emerson Micro Motion 3500 User manual

Emerson

Emerson Rosemount 708 User manual

Emerson

Emerson Rosemount 3051HT User manual

Emerson

Emerson Rosemount 3051S Series User manual

Emerson

Emerson Rosemount 1199 User manual

Emerson

Emerson Rosemount 3300 Series User manual

Emerson

Emerson Rosemount 3100 Series User manual

Emerson

Emerson Rosemount 4600 User manual

Emerson

Emerson Incus GDU-01-TT User manual

Emerson

Emerson Rosemount 644R User manual

Emerson

Emerson Rosemount 2240S User manual

Emerson

Emerson Rosemount 2051 User manual

Emerson

Emerson Fisher 4211 User manual

Emerson

Emerson Rosemount 3051SF Series User manual

Emerson

Emerson Rosemount 3308 Series User manual

Emerson

Emerson Rosemount 520 User manual

Emerson

Emerson Rosemount 1208A User manual

Emerson

Emerson Rosemount 644 User manual

Emerson

Emerson Rosemount 3051 User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction