Emerson Micro Motion 5700 User manual
Installation Manual
MMI-20029768, Rev AA
March 2016
Micro Motion® Model 5700 Ethernet
Transmitters
Ethernet Installations
Emerson Flow customer service
Email:
•Worldwide: [email protected]
•Asia-Pacific: [email protected]
Telephone:
North and South America Europe and Middle East Asia Pacific
United States 800-522-6277 U.K. 0870 240 1978 Australia 800 158 727
Canada +1 303-527-5200 The Netherlands +31 (0) 704 136 666 New Zealand 099 128 804
Mexico +41 (0) 41 7686 111 France 0800 917 901 India 800 440 1468
Argentina +54 11 4837 7000 Germany 0800 182 5347 Pakistan 888 550 2682
Brazil +55 15 3413 8000 Italy 8008 77334 China +86 21 2892 9000
Venezuela +58 26 1731 3446 Central & Eastern +41 (0) 41 7686 111 Japan +81 3 5769 6803
Russia/CIS +7 495 981 9811 South Korea +82 2 3438 4600
Egypt 0800 000 0015 Singapore +65 6 777 8211
Oman 800 70101 Thailand 001 800 441 6426
Qatar 431 0044 Malaysia 800 814 008
Kuwait 663 299 01
South Africa 800 991 390
Saudi Arabia 800 844 9564
UAE 800 0444 0684
Contents
Chapter 1 Planning ...........................................................................................................................1
1.1 About this document ..................................................................................................................... 1
1.2 Related documentation ................................................................................................................. 1
1.3 Installation checklist .......................................................................................................................2
1.4 Additional considerations for retrofitting existing installations .......................................................3
1.5 Power requirements .......................................................................................................................4
1.6 Model 5700 transmitters in Ethernet networks ...............................................................................5
Chapter 2 Mounting and sensor wiring .............................................................................................8
2.1 Mounting and sensor wiring for integral-mount transmitters ......................................................... 8
2.2 Mount the 4-wire or 9-wire remote-mount transmitters .................................................................8
2.3 Wire the 4-wire or 9-wire remote-mount transmitter to the sensor .............................................. 12
2.4 Ground the meter components ....................................................................................................16
2.5 Rotate the transmitter on the sensor (optional) ........................................................................... 19
2.6 Rotate the user interface on the transmitter (optional) ................................................................ 22
2.7 Rotate the sensor wiring junction box on a remote-mount transmitter (optional) ........................ 24
Chapter 3 Wiring the channels ....................................................................................................... 28
3.1 Wire the I/O channel .................................................................................................................... 28
3.2 Wire the Ethernet channels .......................................................................................................... 36
Chapter 4 Power supply wiring ...................................................................................................... 40
4.1 Wiring the power supply .............................................................................................................. 40
4.2 Wire the power supply using an M12-terminated cable (optional) ................................................41
Chapter 5 Power up the transmitter ............................................................................................... 43
Chapter 6 Guided Setup ..................................................................................................................44
Chapter 7 Using the Display controls .............................................................................................. 45
Chapter 8 Available Service Port connection ...................................................................................49
Contents
Installation Manual i
Contents
ii Micro Motion® Model 5700 Ethernet transmitters
1 Planning
Topics covered in this chapter:
•About this document
•Related documentation
•Installation checklist
•Additional considerations for retrofitting existing installations
•Power requirements
•Model 5700 transmitters in Ethernet networks
1.1 About this document
This manual provides information on planning, mounting, wiring, and initial setup of the
transmitter. For information on full configuration, maintenance, troubleshooting, or
service of the transmitter, see the configuration and use manual.
The information in this document assumes that users understand:
•Basic transmitter and sensor installation, configuration, and maintenance concepts
and procedures
•All corporate, local government, and national government safety standards and
requirements that guard against injuries and death
1.2 Related documentation
You can find all product documentation via the Micro Motion product documentation DVD
shipped with the product or at www.micromotion.com.
Additional documentation and resourcesTable 1-1:
Topic Document
Sensor Sensor documentation
Transmitter configuration
and use
Micro Motion Model 5700 Transmitters Ethernet Configuration and Use
Manual
Product Data Sheet Micro Motion Model 5700 Product Data Sheet (PDS)
Ethernet EtherNET/IP Micro Motion Model 5700 Transmitters Ethernet EtherNet/IP Rockwell
RSLogix Integration Guide
PROFINET Micro Motion Ethernet PROFINET Siemens Integration Guide
Modbus configuration Modbus Interface Tool (MIT) — available at www.micromotion.com
Planning
Installation Manual 1
Additional documentation and resources (continued)Table 1-1:
Topic Document
Hazardous area installation See the approval documentation shipped with the transmitter, or
download the appropriate documentation from the Micro Motion
web site at www.micromotion.com.
1.3 Installation checklist
□Safety messages are provided throughout this content to protect personnel and
equipment. Read each safety message carefully before proceeding to the next step.
□If possible, install the transmitter in a location that will prevent direct exposure to
sunlight. The environmental limits for the transmitter may be further restricted by
hazardous area approvals.
□If you plan to mount the transmitter in a hazardous area:
-Verify that the transmitter has the appropriate hazardous area approval. Each
transmitter has a hazardous area approval tag attached to the transmitter
housing.
-Ensure that any cable used between the transmitter and the sensor meets the
hazardous area requirements.
-For ATEX/IECEx installations, you must strictly adhere to the safety instructions
documented in the ATEX/IECEx approvals documentation available on the Micro
Motion Product Documentation DVD shipped with the product or at
www.micromotion.com. Be sure to reference this documentation in addition to
the information shown in this guide.
□Verify that you have the appropriate cable and required cable installation parts for
your installation. For wiring between the transmitter and sensor, verify the
maximum cable length does not exceed 1000 ft (300 m).
□Ensure that you use the following cable for the different connections:
-A twisted-pair instrument cable for the Channel C I/O connection
-A shielded Cat5e or higher rated instrumentation cable for the Ethernet
connections
□You can mount the transmitter in any orientation as long as the conduit openings or
transmitter display do not point upward.
Installing the transmitter with the conduit openings or transmitter display facing
upward risks condensation moisture entering the transmitter housing, which could
damage the transmitter.
Following are examples of possible orientations for the transmitter.
Planning
2 Micro Motion® Model 5700 Ethernet transmitters
Possible transmitter orientationTable 1-2:
Preferred orientation Alternate orientations
□Mount the meter in a location and orientation that satisfies the following conditions:
-Allows sufficient clearance to open the transmitter housing cover. Micro Motion
recommends 8–10 inches (200–250 mm) clearance at the wiring access points.
-Provides clear access for installing cabling to the transmitter.
1.4 Additional considerations for retrofitting
existing installations
□The transmitter installation may require 3–6 inches (76–153 mm) of additional
wiring for the input/output and power connections. This length would be in addition
to the currently installed wiring. Confirm you have the additional wiring necessary
for the new installation.
□Before removing the existing transmitter, be sure to record the configuration data
for the currently installed transmitter. At initial startup of the newly installed
transmitter, you will be prompted to configure the meter via a guided setup.
Micro Motion recommends that you record the following information (if applicable):
Variable Setting
Tag
Mass flow units
Volume flow units
Density units
Temperature units
Channel configuration
mA output 1 -Power (Internal or External):
-Source:
-Scaling (LRV, URV):
-Fault Action:
mA output 2 (optional) -Power (Internal or External):
-Source:
-Scaling (LRV, URV):
-Fault Action:
Planning
Installation Manual 3
Variable Setting
Frequency output (optional) -Power (Internal or External):
-Source:
-Scaling (LRV, URV):
-Fault Action:
-Dual output:
Discrete output (optional) -Power (Internal or External):
-Source:
-Scaling (LRV, URV):
-Fault Action:
Discrete input (optional) -Power (Internal or External):
-Source:
-Scaling (LRV, URV):
-Fault Action:
Calibration parameters (for 9-wire installations only)
Flow calibration factor -FCF (Flow Cal or Flow Calibration Factor):
Density calibration factors -D1:
-D2:
-K1:
-K2:
-TC:
-FD:
1.5 Power requirements
Self-switching AC/DC input, automatically recognizes supply voltage:
•85 to 265 VAC, 6.5 watts typical, 9 watts maximum
•18 to 100 VDC, 6.5 watts typical, 9 watts maximum
Note
For DC power:
•Power requirements assume a single transmitter per cable.
•At startup, the power source must provide a minimum of 1.5 amps of short-term current per
transmitter.
•Length and conductor diameter of the power cable must be sized to provide 18 VDC
minimum at the power terminals, at a load current of 0.7 amps.
Table sizing formula
M = 18V + (R × L × 0.7A)
•M: minimum supply voltage
•R: cable resistance
Planning
4 Micro Motion® Model 5700 Ethernet transmitters
•L: cable length (in Ω/ft)
Typical power cable resistance at 68 °F (20 °C)
Wire gauge Resistance
14 AWG 0.0050 Ω/ft
16 AWG 0.0080 Ω/ft
18 AWG 0.0128 Ω/ft
20 AWG 0.0204 Ω/ft
2.5 mm20.0136 Ω/m
1.5 mm20.0228 Ω/m
1.0 mm20.0340 Ω/m
0.75 mm20.0460 Ω/m
0.50 mm20.0680 Ω/m
1.5.1 Maximum cable lengths between sensor and transmitter
The maximum cable length between the sensor and transmitter that are separately
installed is determined by cable type.
Maximum cable lengths between sensor and transmitterTable 1-3:
Cable type Wire gauge Maximum length
Micro Motion 4-wire Not applicable •1000 ft (300 m) without Ex-
approval
•500 ft (150 m) with IIC rat-
ed sensors
•1000 ft (300 m) with IIB rat-
ed sensors
Micro Motion 9-wire Not applicable 1000 ft (300 m)
User-supplied 4-wire VDC 22 AWG (0.35 mm2) 300 ft (90 m)
VDC 20 AWG (0.5 mm2) 500 ft (150 m)
VDC 18 AWG (0.8 mm2) 1000 ft (300 m)
RS-485 22 AWG (0.35 mm2) or
larger
1000 ft (300 m)
1.6 Model 5700 transmitters in Ethernet networks
You can install the Model 5700 transmitter in star, ring, or daisy-chain networks using
industrial-rated shielded Ethernet cables.
•Make sure that each cable is no longer than 100 meters.
Planning
Installation Manual 5
•Connect the Model 5700 transmitter to the host system via a LAN (Local Area
Network) and not a WAN (Wide Area Network).
•Follow all network security best practices.
1.6.1 Star topology
Model 5700 transmitters can be installed in a star network.
Model 5700 star networkFigure 1-1:
A. Programmable Logic Controller (PLC)
B. Model 5700 with Ethernet output
C. External Ethernet switch
1.6.2 Ring topology
Model 5700 transmitters can be installed in a ring network.
Planning
6 Micro Motion® Model 5700 Ethernet transmitters
Other manuals for Micro Motion 5700
15
Table of contents
Other Emerson Transmitter manuals
Emerson
Emerson MICRO MOTION 2700 Quick guide
Emerson
Emerson Rosemount 248 User manual
Emerson
Emerson Magtech LTM-350 Series Manual
Emerson
Emerson Rosemount 3051S Series User manual
Emerson
Emerson Micro Motion 9739 MVD Quick guide
Emerson
Emerson Rosemount 3051 User manual
Emerson
Emerson Rosemount 3408 User manual
Emerson
Emerson Rosemount 3051S Series User manual
Emerson
Emerson MICRO MOTION 2700 User manual
Emerson
Emerson Micro Motion 2400S Quick guide
Emerson
Emerson Rosemount 2051HT User manual
Emerson
Emerson Rosemount 4088B MultiVariable User manual
Emerson
Emerson Rosemount 2051 User manual
Emerson
Emerson Rosemount FCL-01 User manual
Emerson
Emerson Rosemount 1408H User manual
Emerson
Emerson Rosemount 3100 Series User manual
Emerson
Emerson Rosemount 3051S Series User manual
Emerson
Emerson Rosemount MultiVariable 4088A User manual
Emerson
Emerson Micro Motion 3700 User manual
Emerson
Emerson Rosemount 3051 User manual
Popular Transmitter manuals by other brands
Dejero
Dejero EnGo 3x manual
Rosemount
Rosemount 4600 Reference manual
Speaka Professional
Speaka Professional 2342740 operating instructions
trubomat
trubomat GAB 1000 instruction manual
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 instructions
Rondish
Rondish UT-11 quick start guide
