Elvaco CMi6160 User manual
MOUNTING - BATTERY POWER
See manual for external battery pack. Connect power cable from
external battery back to battery power connector (4) of the CMi6160.
ANTENNA CONNECTION
If the CMi6160 is equipped with internal antenna no additional actions
need to be taken. If external antenna is required disconnect the internal
antenna (if it is mounted) from MCX connector of CMi6160. See picture
below for internal antenna positioning.
Connect an external antenna (released by the supplier) with MCX
connector to the module CMi6160 in the meter. Make a hole in rubber
gromets/sealing and push the mcx connector through the gromet/
sealing. Make sure thicker part of antenna cable is in gromet/seal. Push
the connector gently into the antenna connector (7) on the module.
MOUNTING
Before mounting the module in the meter, make sure that a SIM card is
installed in the SIM card slot (5) as illustrated above.
NOTE! Please note that the SIM card must be inserted as illustrated
below. If it is inserted upside down it can easily damage the SIM slot.
Open the calculator by folding down the side catches.
Lock the module into the appropriate slot (preferable slot 2, mandatory
when internal antenna is used) and carefully connect the pre-formed
ribbon cable at both ends.
Close the lid and check the meter for correct operation by pressing the
push button. Apply tamper evident seal of the housing lid if the meter
functions correctly.
NOTE
• Electrostatic-sensitive devices. Please observe the
necessary ESD protective measures when installing
the device.
INTRODUCTION
CMi6160 is an integrated meter connectivity module mounted inside
a Diehl Metering SHARKY 775 heat/cold meter and SCYLAR INT 8
calculator to deliver meter data to a receiving system via a NB-IoT
network. For a complete description of the product, or for information in
other languages, please visit the Elvaco AB website, https://www.elvaco.
com.
MODULE SPECIFICATION
CMi6160
Integrated MCM for Diehl Metering SHARKY 775, SCYLAR INT 8, NB-IoT
ACTIVATION
Upon delivery, CMi6160 has a standard conguration. To change the
conguration, please download the Elvaco OTC Application (One-
Touch commissioning) for Android, available in Google Play, for iOS
available in app store.
The Elvaco OTC connects to the module via NFC.
NOTE
• Make sure to locate the NFC antenna on your phone. When you
scan or write new congurations to the module, you should place
the phone’s NFC antenna as close as possible to the NFC antenna
of the module (8). The NFC is reachable from back side of the
meter or from top when lid is removed.
1. Meter Interface
2. Green LED
3. Red LED
4. Battery Power Connector
5. SIM Card Holder
6. Push Button
7. Antenna Connector (MCX)
8. NFC Antenna (around whole
board)
© 2021, Elvaco AB. All rights reserved. The documentation and product are provided on an “as is” basis only and may contain deciencies or inad-
equacies. Elvaco AB takes no responsibility for damages, liabilities or other losses by using this product. No part of the contents of this manual
may be transmitted or reproduced in any form by any means without the written permission of Elvaco AB. Printed in Sweden.
CMi6160 Quick manual English
Version: 1.0
TECHNICAL SPECIFICATIONS
Mechanics
Dimensions (w x h x d) 43 x 37 x 9 mm
Mounting In Diehl Metering SHARKY 775 or SCYLAR
INT 8 module slot 2
External antenna
connector
MCX female
Antenna max gain 4 dBi
SIM card Slide, size Nano
Electrical connections
Battery supply Externally mounted Diehl Metering
D-Cell
Battery life time 13+1 year
The battery life time is based on ECL0 and
hourly reading sent once / day.
Electrical characteristics
Nominal voltage Battery 3.0 VDC
Power consumption
(max)
400 mA
Power consumption
(sleep mode)
6µA
Environmental specifications
Operating temperature +5 °C to +55 °C
Operating humidity 0 - 93 % RH, no condensation
Operating altitude 2000 m
Pollution degree Degree 1
Usage environment Indoors
Storage temperature -20 °C to +60 °C (Module)
Mobile network
Band 20, 8, 3 (NB-IoT)
3GPP Release 14 (NB2)
Transmit power Maximum 23.0 dBm
Receiver sensitivity -135 dBm
User interface
Green LED Start-up, Network connection
Red LED Start-up
Push button Start-up, Reboot
Conguration • NFC via Elvaco OTC App
• Via LwM2M (Elvaco Evo DM-system, or
third-party DM-system)
• Precong on delivery
CONTACT INFORMATION
Elvaco AB Technical support:
Online: www.elvaco.com
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Elvaco declares that the radio equipment type CMi6160 is in
compliance with the following directives:
- 2014/30/EU (EMC)
- 2014/35/EU (LVD)
- 2014/53/EU (RED)
- 2011/65/EU + 2015/863 (RoHS).
The complete Declaration of Conformity can be found at www.elvaco.
se/en > Search on product name.
SIMPLIFIED UK DECLARATION OF CONFORMITY
Hereby, Elvaco declares that the radio equipment type CMi6160 is in
compliance with the following directives:
- Electromagnetic Compatibility Regulations 2016
- Electrical Equipment (Safety) Regulations 2016
- Radio Equipment Regulations 2017
- The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
The complete Declaration of Conformity can be found at www.elvaco.
se/en > Search on product name
SAFETY
Install the antenna / product minimum distance 20 cm from person.
The warranty does not cover damage to the product caused by usage in
any other way than described in this manual. Elvaco AB can not be liable
for personal injury or property damage caused by usage in any other way
than described in this manual.
By default, the product is set to passive mode, which means no messages
will be transmitted from the device. There are two ways to activate the
product:
1. Press and hold down the push button (6) for at least 5 seconds until
the green LED (2) lights up.
2. Via the Elvaco mobile application. Go to the Apply tab, set the
Power mode to “Active”, push “Apply” and place the phone on the
back side of the meter, next to the module. Make sure to hold the
phone still until the phone vibrates.
Upon start-up, the module will attempt to connect to the mobile
network. The phase is indicated by short flashes on the green LED. After
successfully connecting to the mobile network, the green LED will light
up for 8 seconds, as indicated by the gure below.
Other manuals for CMi6160
1
Other Elvaco Computer Hardware manuals
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
