ELRO LT350512P User manual

ELRO LT350512P – LT351012P

TWIN HEAD SPOTLIGHT

LED Light Lamp Cap

Wall Box Main Body

PIR (Motion Sensor)

INTRODUCTION

The ELRO Twin Head LED Spotlight offers you an

economical lighting solution with extremely low energy

consumption.

During darkness, the built-in passive infrared (PIR) sensor

turns on the Spotlight when the PIR sensor detects a

moving heat source in its coverage area.

Two beam adjustable spotlights allow you to provide the

optimum lighting coverage.

Note: Read this entire manual before you start to

install the system.

SAFETY PRECAUTIONS

DO NOT install when it is raining.

Isolate the power supply before installation.

HO5RNF round flexible cable and drip loops must

be used to avoid water ingress damage to the unit.

Ensure that the power supply is protected by a 6A

circuit breaker or suitable fuse.

Ensure minimum distance of 0.5m away from

lighted objects.

CHOOSING A MOUNTING LOCATION

For the best results, mount the Spotlight onto normal

brickwork 2.0m above the ground.

Avoid aiming the PIR sensor at pools, heating vents,

air conditioners or objects that may change

temperature.

Avoid pointing the PIR sensor at trees or shrubs or

where the movement of pets or animals may be

detected.

WIRING INSTRUCTION

(1) WARNING isolate the power supply. An internal

single pole wall switch is recommended to allow

easy control of the Spotlight.

(2) Remove the wall box screw at the base of the unit

(3) Use a pin to punch a small hole in the cable

grommet, enabling the supply cable to enter the wall

box.

(4) Route the supply cable through the cable grommet.

A drip loop is required between the wall box and the

wall to avoid water ingress.

(5) Strip approximately 6-8mm of inner core insulation

from the supply cable.

(6) Refit the Spotlight onto the wall box and secure with

the two clips. Refit the wall box screw at the base of

the unit (if fitted).

Note: If you need to detach the Spotlight from the wall box.

WARNING isolate the power supply. side and one on the

right side of the wall box. (FIGURE 7). Support the fitting

during the process to prevent it from falling.

AC POWER

LIVE

NEUTRAL

Cable Fastener

ADJUSTMENTS

The LED spotlight heads and the PIR cab be adjusted

vertically and horizontal

The beam angle of

the LED spotlight

heads can be

adjusted by turning

the Lamp Cap Rings

around the LED

spotlight heads.

(1) TEST MODE

Turn the LUX control and the TIME control counter

clockwise to the edge – the TEST position.

Turn on the wall switch. The light starts warm-up for

1 minute. During 1 minute warm-up period, the light

will stay on.

Walk through the detection area. The light turns on

when you move and turns off when you stop.

For a smaller coverage area, point the sensor down;

for a larger coverage area, point the sensor up.

(2) TIME ADJUSTMENT

The TIME adjustment controls how long the light will stay

on after the motion has been detected.

About 5 seconds About 12 minutes

(3) LUX ADJUSTMENT

The LUX adjustment determines at what

light level the lighting system will start

operating when you set the sensor to

automatic operation.

(4) AUTOMATIC OPERATION

Turn on the wall switch. When the sensor detects motion,

the light automatically turns on. The built-in photocell

turns the sensor off and on according to the light level

selected by the LUX adjustment.

(5) MANUAL OVERRIDE CLICK TWICE

To keep the light on regardless of the motion, you can

override the Automatic Operation. Turn the wall switch off

and on twice within 4 seconds. The interval between the

first and second operation must be within 0.5 - 2 seconds.

In Manual Override mode, the light will remain on for

around 4 ~ 6 hours despite no motion; then the light will

turn off and the motion sensor will be back to Auto

Operation mode automatically.

Users can also set the motion sensor back to Auto

Operation by turning off the wall switch for at least 10

seconds and then turn it back on

SPECIFICATIONS

Power Requirement

AC 220 - 240V / 50 Hz

LP350512P

LP351012P

2 x 5 Watt = 10 Watt

2 x10Watt = 20 Watt

Standby

0.5 Watt

LED

Cree

Color Temperature (K)

5000K

CRI

>70

Lumen LP350512P @80°

Lumen LP351012P @80°

850 lumen

1550 lumen

Beam Adjustment

Beam angle MAX 80°

L70 Life Span (hours)

Up to 30000 hr

Detection Angle

Up to 180° at 2m Height

Detection Range

Up to 12m (39.4ft) at 2m

Height

Sensor Swiveling Angle

Up to 45° Leftward

Up to 45° Rightward

Up to 35° Downward

Light Adjustable Angle

Up to 45o Leftward

Up to 45° Rightward

Up to 37.5° Downward

Mounting Height

Recommended 2m

(6.56ft) Wall Mount

Time Adjustment

5 seconds - 12 minutes

Lux Adjustment

30 - 200 Lux

Operation Mode

Off/Auto/Manual override

Warm Up Time

About 60 seconds

Working Temperature

-10°C ~ +40°C;

95%RH max

Protection Class

Class II

Protection Degree

IP44

This manual suits for next models

Other ELRO Spotlight manuals

ELRO

ELRO LP351012P User manual

Popular Spotlight manuals by other brands

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 user manual

LIVARNO home

LIVARNO home 375304 2101 Installation, operating and safety information

Cameo

Cameo CLQS40WW user manual

Leviton

Leviton Ellipsoid 5/50 user guide

Monacor

Monacor img Stage Line PARL-56PDX/CR instruction manual

Vector

Vector SL3AKV instruction manual

Quantum

Quantum Q262 Product data sheet

Philips

Philips Vari-lite VL3015LT user manual

EUROSPOT

EUROSPOT C51 instruction manual

DTS

DTS MINI BRICK ARC user manual

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Installation, operation and maintenance instructions

ACME

ACME LED-MS350B user manual

EuroLite

EuroLite Akku flat light 1 user manual

Commercial Electric

Commercial Electric SPTM-1401 Use and care guide

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Instructions for use

Teknik

Teknik FLEXI user manual

Craftsman

Craftsman CMXLSB10 instruction manual

EuroLite

EuroLite LED SLS-144 UV Floor Spot user manual