EliteProAV Saker Series User manual

Rev.042417-D

www.eliteproav.com

Saker

Series

Electric Wall/Ceiling Projection Screen

User’s Guide - E Type (RC1)

V.1

Visit www.elitescreens.com for latest updated version.

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra

Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite ProAV™.

Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit

are prohibited and will void your warranty.

•

Please retain this user’s guide for future reference.

•

To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

•

Handle the unit carefully during transportation to avoid any damage.

•

To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

•

The power outlet supplying power to the unit should be close to the unit and easily accessible.

•

Do not install the unit on uneven or inclined surfaces.

•

Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

•

Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short

circuit.

•

There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.

No one except authorized technicians can open and make repairs to this unit.

•

Make sure the power source this unit is connected to has a continuous power flow.

•

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid overheating.

•

Do not handle the power plug when your hands are wet, or your feet are in contact with water.

Do not use this unit under the following circumstances.

•

Disconnect the power cord under the conditions of heavy rain, wind, thunder, or lightning.

•

Avoid direct Sunshine, rain shower and moisture.

•

Keep away from fire sources and high temperatures to prevent this device from overheating.

•

Cut off the power supply first before transportation or maintenance.

•

Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

•

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

Rev.09252023-JA

www.eliteproav.com

WARNING

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite ProAV™Customer Service for any questions.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures.

✓Reorient or relocate the receiving antenna of the device which may be causing the

interference.

✓Increase the separation between the screen and the device’s receiver.

✓Connect the equipment to a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. Included mounting screws

are complimentary and may not be appropriate for all mounting surfaces. Use appropriate anchors to safely

secure the screen to the mounting surface or consult with a professional installer.

Hardware Parts List

Please make sure all parts listed below are included before proceeding with the installation.

A. Wall/Ceiling mount

bracket x2 B. M5x60 Screw x4 C. M12 Dry-wall

anchor x4 D. Bracket

connector x2 E. M5x11 Bolt

Screw x4

For 135”below For135”-180”

F. M5x25MM round head

cross screws x2

G. M5x30MM eyebolt

screw & M5 nut x2

H. Hidden wall

bracket x2

I. R18xR6x1

washer x4

J. Snap link x2

Rev.09252023-JA

www.eliteproav.com

Installation Instructions

For installation assistance, please consulta professional Installer. EliteProAV™is not liable for faulty installations.

Rev.09252023-JA

www.eliteproav.com

B. Ceiling Mount

I. Ceiling Mount (fixed position on end caps)

Dry-wall anchors (C) Ceiling

Washer (I)

M5x60 screw (B)

NOTE: The brackets do not slide. They are designed to attach the end caps only.

1. Attach the Wall/Ceiling mount bracket (A) to the Bracket connector (D) located on top of the screen’s

housing (preinstalled).

2. Determine where the screen will be installed. Then, measure and mark the distance between the (WxH)

locations.

3. Drill a hole on all marked areas and insert a dry-wall anchor(C).

4. Secure the screen by inserting the M5x60 screw (B) and a washer (I) thru the wall/ceiling mount

brackets (A). Two or more people are required while one holds the screen in place.

II. Suspended

1. Screw the eyebolt (G) on the bracket connector (D).

2. Attach the snap link (J) through the eyebolt (G) and connect it to an eyebolt screw (not included) rated for

the screen’s weight.

Starling Tab-Tension | Controls and Accessories

A. IR Remote

ZRC1-IR-W1

B. RF Remote

ZRC1-RF-W1

C. Wall box

controller

ZRC-WB-W1

D. RJ50 cable

ZRC1-RJ50

G. AAA

batteries

H. Bubble level

Rev.09252023-JA

www.eliteproav.com

Screen operation

Electric Current: 110v.

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen’s has power, you’ll be able to control it using any of the 6 methods described below.

5 Ways to control your Starling Tab-Tension screen

1. IR Remote control (Item A, Fig 1): The Infrared functions by direct line of

sight contact using an effective beam range of 25 feet within a 30-degree angle.

Aim the IR remote directly at either the IR receiver on the Wall Box Controller

or on the screen to operate the screen.

Note: Assure there is no obstruction between the IR remote and IR receiver.

2. RF Remote Control (Item B): The radio waves eliminate the need for a direct line of

sight and has a longer distance control range.

The RF remote is already pre-synced/paired and ready to use. If synchronization/ pairing

is needed, please follow the steps below.

How to synchronize/pair a new RF remote:

•Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-box LED

flashes). Reference the wall box controller section for programming key location.

•Then press the “Up Key” on the RF remote.

•The Wall box LED will flash 5 times, to indicate the RF remote has been properly synchronized/paired.

How to change the RF code (For use when multiple screens/RF remotes are owned)

Changing the RF code avoids controlling multiple screens at the same time and prevents electrical interference

leading to accidental control of the screen.

1. Remove the batteries

2. Change the RF code switch

3. Insert the batteries

4. Synchronize it with the wall box controller

Battery compartment

Default

“000”

RF Remote

BACK VIEW

Slide Switches

for RF Code

change

LED light

STOP

DOWN

Fig.1

IR/RF remote

IR Lens

(IR remote only)

Rev.09252023-JA

www.eliteproav.com

3. Wall box controller (Item C, Fig 3): The wall box controller switch is a wall mounted control box with an

up/stop/down button. It plugs directly into the screen’s RJ50 port.

4.Wired 5-12 volt trigger: Requires a 3.5mm to 3.5mm mono cable (not included)

Step 1: Connect one end of the RJ50 cable to the screen and the other

end to the Wall box controller.

Step 2: Then connect one end of the 3.5mm mono cable to the wall box

controller and the other to the projector.

Once the two cables have been connected, the wired trigger feature is

ready to synchronize the screen’s up/down operation with the

projector’s power cycle.

•Projector on, screen drops

•Projector off, screen raises

5. Wireless 5-12 volt trigger (Fig 5): Requires a 3.5mm to 3.5mm mono cable (not included).

The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld remote control, or

as a Wireless 5-12 volt trigger. The radio frequency technology sends a wireless signal that synchronizes the

screen’s drop & rise with the projector’s power cycle.

Wall box controller

IR Receiver

RJ50 cable

Wall box controller

SIDE VIEW

RJ50 PORT:

Connects to the

Screen RJ50 PORT

(RJ50 CABLE ONLY)

3.5mm mono Projector

Trigger Port (if Projector

equipped)

Wall box controller

BACK VIEW

Programming

Key

Fig 5

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

STOP

DOWN

Projector

Mono 3.5mm

Projector Trigger

Port

RF remote control

SIDE VIEW

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

Wall box controller

Fig. 4

RJ50 cable

Projector

Rev.09252023-JA

www.eliteproav.com

Here’s how to set up your Wireless 5-12 volt trigger

The 5-12V wireless trigger should already be synced and ready to work.

Step1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm mono end of the cable to your projector

Step 3: Turn on the projector and the screen should automatically deploy.

Step 4: Turn off your projector and the screen should automatically retract.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30seconds

for full off and on cycle each time)

Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box controller per the

instructions in the Radio Frequency remote section.

ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)

❖Wall box controller must be connected to the screen.

1. Preset the Screen’s Drop Position:

Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it at.

Press & hold the “Programming Key”, then press the “Down key”on the Wall Box Controller. The LED will flash 5

times to confirm new programmed drop position.

2. Clear/Reset the Screen’s Drop Position to factory default:

Press & hold the “Programming Key + “Stop key” on the wall box controller.

For more information, technical support or your local Elite Screens contact, please

visit www.eliteproav.com

PROGAMMING NOTE:

The programmed vertical position relies on a time-count which adjusts itself according to the programmed

timed difference. Multiple up/down programming will result in the vertical position being off a few inches. It

is recommended that programming is done the first-time the desired vertical position is determined or RESET

it to factory default and programming the desired vertical position afterwards.

ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the projection surface

on tab-tension screens. The full drop is recommended to allow the screen to rely on the tab-tension system

to maintain the projection surface flat and taut on all sides.

The same applies on non-tensioned screens, although some level of waves may be present due to the

nature of the screen not being tensioned. If wrinkles/waves develop after making the adjustment to the

desired drop position, reset it to the factory’s default position per the instructions below.

FLATNESS AFFECTED BY NEW PROGRAMMED VERTICAL POSITION IS NOT COVERED UNDER A REPLACEMENT

WARRANTY.

Table of contents

Other EliteProAV Projection Screen manuals

EliteProAV

EliteProAV Saker Tab-Tension CineGrey 5D Series User manual

EliteProAV

EliteProAV Planate Tab-Tension Series User manual

EliteProAV

EliteProAV Spectrum2 Series User manual

EliteProAV

EliteProAV CLR Series User manual

EliteProAV

EliteProAV Manual Grande 2 Series User manual

EliteProAV

EliteProAV EDGE FREE Aeon ALR Series User manual

EliteProAV

EliteProAV AV Manual B Series Instruction manual

EliteProAV

EliteProAV Pro Frame Thin Series User manual

EliteProAV

EliteProAV Presenter Pro DarkUST 2 Series User manual

EliteProAV

EliteProAV Kestrel Stage Series Quick reference guide

EliteProAV

EliteProAV WhiteBoardScreen TE Series User manual

EliteProAV

EliteProAV CineGrey 5D User manual

EliteProAV

EliteProAV ITE139XW2-E8 User manual

EliteProAV

EliteProAV Planate Tab-Tension Series User manual

EliteProAV

EliteProAV Presenter Pro CLR 2 User manual

EliteProAV

EliteProAV Tab-Tension Pro Series User manual

EliteProAV

EliteProAV T153UWS1-D User manual

EliteProAV

EliteProAV Pro Frame Acoustic Series User manual

EliteProAV

EliteProAV Yard Master Pro 2 Series User manual

EliteProAV

EliteProAV TensionPro TP200 XHW2 User manual

EliteProAV

EliteProAV Pro Frame Series User manual

EliteProAV

EliteProAV EDGE FREE Pro Frame Thin UST Series User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Da-Lite

Da-Lite ExecutiveElectrol Instruction book

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs