Elite 01332 User manual
eLite LED Tube Lighting
InstructIon Manual
Item #s 01330, 01331, 01332, 01333, 01334
1. A. If the appliance shows any sign of abnormal
water leakage, immediately unplug it from the
power source.
B. Carefully examine the appliance after installation.
It should not be plugged in if there is water on
the parts not intended to be wet.
C. Do not operate any appliance if it has a damaged
cord or plug, if it is malfunctioning or if it is
dropped or damaged in any manner.
D. To avoid the possibility of the appliance plug or
receptacle getting wet, position aquarium stand and
and tank to one side of the wall mounted receptacle
to prevent water from dripping onto the receptacle
or plug. A “drip loop,” shown in the figure below,
should be arranged by the user for each cord
connecting an aquarium appliance to the
receptacle. The “drip loop” is the part of the cord
below the level of the receptacle, or the connector
if an extension cord is used, to prevent water
travel along the cord and coming in contact with
the receptacle. If the plug or the receptacles do
get wet, DO NOT unplug the cord. Disconnect the
fuse to the circuit breaker that supplies power to
the appliance. Then unplug and examine for the
presence of water in the receptacle.
2. Close supervision is necessary when any appliance
is used by or near children.
3. To avoid injury, do not contact moving parts or hot
parts such as heaters, reflectors, lamp bulbs, etc.
4. Always unplug an appliance from the outlet when
not in use, before putting on or taking off parts, and
before cleaning. Never yank the cord to pull plug from
the outlet. Grasp the plug and pull to disconnect.
5. Do not use an appliance for other than intended use.
The use of attachments not recommended or sold
by the appliance manufacturer may cause an
unsafe condition.
6. Do not install or store the appliance where it will
be exposed to the weather or to temperatures
below freezing (32oF/0oC).
7. Make sure an appliance mounted on a tank is
securely installed before operating it.
8. Read and observe all the important notices on
the appliance.
9. If an extension cord is necessary, a cord with a
proper rating should be used. A cord rated for less
amperes or watts than the appliance rating may
overheat. Care should be taken to arrange the
cord so that it will not be tripped over or pulled
from outlet.
10. ONLY FOR POLARIZED ATTACHMENT PLUG
APPLIANCES: If this appliance has a polarized plug
(one blade is wider than the other) as a safety feature,
this plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can
be fully inserted. Do not attempt to defeat this
safety feature.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To guard against injury, basic safety precautions should be observed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
DANGER: To avoid possible electric shock, special care should be taken since water is employed in the use of
aquarium equipment. For each of the following situations, do not attempt to repair yourself; return the appliance to
an authorized service facility for service or discard the appliance.
THIS PRODUCT IS INTENDED FOR USE OVER COVERED AQUARIUMS ONLY.
WARNING: This product is NOT SUBMERSIBLE. No part of the eLite LED Tube Light
or transformer is intended to be submerged in water.
NOTE: The transformer is not included with this product. Please purchase the
necessary 1 or 3 tube transformer, which is sold separately.
SAVE THESE INSTRUCTIONS
Drip Loop
Aquarium
appliance
Power
supply
cord
Fig. 1
Parts
Caution: Before installing or operating the lighting, read and understand all safety instructions and warnings.
rEtroFIt InstallatIon
Into an existing fluorescent
light fixture
Turn off and unplug your
existing T5 or T8 fluorescent
light fixture
Allow the lamp to cool for 15 minutes. Remove the
fluorescent lamp from the fixture. The power supply cord
for the existing light fixture will no longer be used and can
be tied up or bound and placed in a location where it will
stay dry and out of the way.
WARNING: LIGHT FIXTURE MUST BE UNPLUGGED–
BIND OR DISCONNECT CORD FROM FIXTURE.
POWER SHOULD NOT BE DELIVERED TO THE FIXTURE
AS THE LED TUBES HAVE THEIR OWN SEPARATE
POWER SUPPLY.
Install the appropriate end
adaptors, either T5 or T8,
that correspond to the
sockets in the light fixture
The adaptor pins will install into the existing lamp sockets
like you would a lamp, by inserting the pins and rotating
them into position.
See Figure 1.
Make sure the adaptor
openings are facing so that the LED tube(s) can be
snapped into the adaptor.
Snap the ends of the LED
light(s) into the adaptors
and rotate the lamp so the
LEDs are facing the direction you
would like the light to shine
You may need to support the adaptor as you snap the LED
light in place. Route the power cord out of the light fixture
and connect the plug for each LED tube light to the 1 or 3
tube transformer (sold separately). Slide the protective
rubber sleeve over the connection(s) to protect it from
moisture. Once all connections are made, the transformer
can be plugged into an acceptable outlet and the eLite LED
Tube Light is ready for use.
A – eLite LED tube light
B – T5 end adaptor (x2)
C – T8 end adaptor (x2)
D – Canopy mounting clip (x2)
A
B
Fig. 2
Caution: Before installing or operating the lighting, read and understand all safety instructions and warnings.
canoPY InstallatIon
Into an aquarium canopy or
existing hood
Install the canopy mounting
clips to the underside
of the canopy using
appropriately sized screws
Hardware used must be capable of supporting the weight of
the installed eLite LED Tube Light. The clips must be installed
in-line with one another and spaced so they will clip
approximately 4 inches in from each end of the LED tube.
See Figure 2.
Snap the ends of the
LED tube light(s) into
the mounting clips and
rotate the lamp so the LEDs are
facing the direction you would
like the light to shine
Connect the plug for each LED tube light to the 1 or 3 tube
transformer (sold separately). Slide the protective rubber
sleeve over the connection(s) to protect it from moisture.
Once all connections are made, the transformer can be
plugged into an acceptable outlet and the eLite LED Tube
Light is ready for use.
C D
Canopy surface (underside)
Installed
in-line
Canopy mounting clips
4" 4"
LED Tube Size/Output
LED Tube LED Lumen
Size Wattage Count Output
18" 3.0 14 280
24" 4.0 20 400
30" 5.5 26 520
36" 7.0 32 640
48" 10.0 45 900
eLite LED Tube
What the Warranty Covers
Elive LLC (Company) warrants this Elive product
(see exclusions below) to the original purchaser against
defective material and workmanship that occurs during
normal in-home use for 12 months from the original
purchase date. The Company will, at the Company’s
option, either repair or replace same without charge (but
no cash refunds will be made). This warranty is limited to
replacement or repair of product only and does not cover
loss of aquarium life, personal injury, property loss, or
damage arising from
the use of the product.
Exclusions:
1. Damage resulting from accident, misuse, abuse, lack
of reasonable care, subjecting the product to any but
the specified electrical service, other than normal or
ordinary use of the product, subjecting the product to
abnormal working conditions or any other failure not
resulting from defects in materials or workmanship.
2. Damage resulting from modification, tampering with,
or attempted repair by anyone other than the Company.
3. Transfer of product to someone other than the
original consumer purchaser.
What you must do to enforce the warranty:
Contact the Company by telephone at
1-855-ELIVE18 / 1-855-354-8318
Or contact the Company by writing to
Elive LLC
2725 South Moorland Road Suite# 102
New Berlin, WI 53151
Attention: Warranty
Or contact the Company by email to
elivesupport@elivepet.com
Via website www.elivepet.com
You must pay any postage, shipping charges, insurance
costs and other expenses to return the product along with
the original cash register receipt to Elive LLC. However,
if the necessary repairs are covered by the warranty, the
Company will pay the return shipping charges to any
destination within the United States or Canada.
Limitation of implied warranties and exclusion
of certain damages:
The Company disclaims liability for incidental and
consequential damages for breach of any express or
implied warranty, including any implied warranty of
merchantability, with respect to this product. This writing
constitutes the entire agreement of the parties with
respect to the subject matter hereof: no waiver or
amendment shall be valid unless in writing signed by
the Company. Some states do not allow the exclusion
or limitation of consequential damages, so the above
limitation or exclusion may not apply to you.
Limited 12-Month Warranty
Elive LLC
2725 South Moorland Road, Suite 102
New Berlin, WI 53151
1.855.ELIVE.18 / 1.855.354.8318
elivepet.com
MADE IN CHINA
This manual suits for next models
4
Other Elite Other manuals
