Elisa EAS428SS Datasheet

Installation Instructions Guide

Instructions d’installation Guide

Guía de Instrucciones para Instalación

READ AND SAVE THESE INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION GUIDE

LEA Y GUARDE ESTAS INSTRUCCIONES

Model: EPR628SS

English p. 3

Français p. 14

Español p. 25

Model: EAS428SS

LI31MB

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

■Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

■Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag to the

service panel.

■Installation work and electrical wiring must be done by

 qualiedperson(s)inaccordancewithallapplicablecodes

 andstandards,includingre-ratedconstruction.

■Sufcientairisneededforpropercombustionand

 exhaustingofgasesthroughtheue(chimney)offuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guideline and safety

standards such as those published by the National Fire

 ProtectionAssociation(NFPA),theAmericanSocietyfor

Heating, Refrigeration and Air Conditioning Engineers

 (ASHRAE),andthelocalcodeauthorities.

■When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use to

exhaust hazardous or explosive materials and vapors.

CAUTION: Toreduceriskofreandtoproperlyexhaustair,

besuretoductairoutside-donotventexhaustairinto

spaces within walls or ceilings, attics or into crawl spaces, or

garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

■Always turn hood ON when cooking at high heat or when

 ambeingfood(i.e.CrepesSuzette,CherriesJubilee,

 PeppercornBeefFlambé).

■Clean ventilating fans frequently. Grease should not be

 allowedtoaccumulateonfanorlter.

■Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TOREDUCETHERISKOFINJURYTO

PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING:a

■SMOTHERFLAMESwithaclosettinglid,cookiesheet,or

metal tray, then turn off the burner. BE CAREFUL TO

 PREVENTBURNS.Iftheamesdonotgoout

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

■NEVERPICKUPAFLAMINGPAN-youmaygetburned.

■DONOTUSEWATER,includingwetdishclothsortowels-

a violent steam explosion will result.

■Use an extinguisher ONLY if:

-YouknowyouhaveaclassABCextinguisher,andyou

already know how to operate it.

 –Thereissmallandcontainedintheareawhereit

started.

 –Theredepartmentisbeingcalled.

 –Youcanghttherewithyourbacktoanexit.

aBased on “Kitchen Fire Safety Tips” published by NFPA.

WARNING: Toreducetheriskofreorelectricalshock,

 donotusethisfanwithanysolid-statespeedcontrol

device.

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical

Inspector’s use.

INSTALLER: Please leave these Instructions with this unit for

the owner.

OWNER: Please retain these instructions for future

reference.

Safety Warning:Turn off power circuit at service panel and lock

out panel before wiring this appliance.

Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit

Table of Contents

Important Safety Notice .......................................................... 3

Tools and parts ........................................................................ 4

Location Requirements ...................................................... 4

Product Dimensions ........................................................... 4

Venting Requirements ........................................................5

Venting Methods ................................................................ 6

Calculating Vent System Length ........................................ 6

Electrical Requirements...........................................................6

Installation Instructions .......................................................... 7

Prepare Location.................................................................7

Install range hood.....................................................................9

Connect the Vent System....................................................10

Complete Installation...........................................................10

Range Hood Use....................................................................... 11

Range Hood Care......................................................................11

Available Accessories.............................................................. 12

Warranty.....................................................................................13

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed (all models)

■Level

■Drill

■ ¹⁄8”(3.0mm)drillbit

■Pencil

■Pliers

■Tape measure or ruler

■Caulking gun and weatherproof caulking compound

■ Flat-bladescrewdriver

■Phillips screwdriver

■Saber or keyhole saw

■Metal snips

■Vent clamps

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ 1-30”x12”(76.2x30.5cm)facepanel

■Damper

■ 2-40Wincandescentlamps(onlymodelEAS428SS)

■ 2-50Whalogenlamps(onlymodelEPR628SS)

■ 2-Metalgreaselters

■ 2-Mountingbrackets

■ 2-Metalspacers(forusewhencabinetdepthisgreater

 than12”)

■Hardware package. Includes:

• Installation Instructions and Use and Care Guide

• 8-metalwashers

• 8-plasticwashers

• 8-4.5x13mmwoodscrews

• 2-4.2x15mmmachinescrews

• 4-3.5x9.5mmat-headsheetmetalscrews

• 8-4.2x19mmsheetmetalscrews

• 6-3.5x9.5mmsheetmetalscrews

• T10 TORX®† adapter

Parts needed

■ 6”(15.2cm)roundmetalventsystem

†®TORX is a registered trademark of Saturn Fasteners, Inc.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Haveaqualiedtechnicianinstalltherangehood.Itisthe

installer’s responsibility to comply with installation clearances

speciedonthemodel/serialratingplate.Themodel/serialrating

plateislocatedinsidethelinerbehindthelterontheleftwallof

the range hood.

Range hood location should be away from strong draft areas,

such as windows, doors, and strong heating vents.Cabinet open-

ing dimensions that are shown must be used. Given dimensions

provideminimumclearance.Consultyourcooktop/rangemanu-

facturer installation instructions before making any cutouts.

Grounded electrical outlet is required. See “Electrical Require-

ments” section.

The range hood is factory set for vented installations through the

rooforwall.Fornon-vented(recirculating)installationssee“Non-

Vented(recirculating)InstallationThroughtheSoft/Cabinet”in

the “Prepare Location” section. Recirculation Kit Part is available

from your dealer or an authorized parts distributor. All openings

in ceiling and wall where range hood will be installed must be

sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR,Part328(formerlytheFederalStandardforMobileHome

ConstructionandSafety,title24,HUD,Part280)orwhensuch

standard is not applicable, the standard for Manufactured Home

Installation1982(ManufacturedHomeSites,Communitiesand

Setups)ANSIA225.1/NFPA501A,orlatestedition,orwithlocal

codes.

Product Dimensions

I*-Metallicspacers

Spacers has to be installed

and used when cabinet depth

is greater than 12”.

EAS428SS / EPR628SS range hood models

Dimension

DIM A 281⁄4”(71.8cm)

DIM B 26”(66cm)

DIM C 1⅛”(2.9cm)

DIM D 10¾”(27.3cm)

DIM E 9½”(24.2cm)

DIM F 5⁄16”(.85cm)

DIM G 14 9⁄16”(37cm)

DIM H 6”(14.8cm)

DIM I ½”(1.27cm)

Installation Clearances

A.12”(30.5cm)min.upper

cabinet height

B.30”(76.2cm)

cabinet opening width*

C.24”(61cm)min.36”(91.4cm)

suggested max. bottom of

cabinet to cooking surface

D.12”(30.48cm)cabinet

opening depth*

E.15”(38.1cm)min.clearance

upper cabinet to countertop

F.36”(91.4cm)basecabinet

height

For gas range installation: Mount this hood so that the bottom

edgeisatminimum27”(68,5cm)abovethecookingsurface.

For electric range installation: mount this hood so that the bottom

isnotlessthan24”(61cm).

*NOTE:Thisrangehoodissetto30”(76.2cm)cabinetwidthx

12”(30.5cm)deepcabinets.

VENTING REQUIREMENTS

■Vent system must terminate to the outdoors, except for no

 vented(recirculating)installations.

■Do not terminate the vent system in an attic or other enclosed

area.

■ Donotusea4”(10.2cm)laundry-typewallcap.

■Use metal vent only. A rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■The length of the vent system and number of elbows should

 bekepttoaminimumtoprovideefcientperformance.

Forthemostefcientandquietoperation:

■Use no more than three 90° elbows.

■ Makesurethereisaminimumof24”(61.0cm)ofstraight

vent between the elbows if more than 1 elbow is used.

■Do not install 2 elbows together.

■The vent system must have a damper.

■Use clamps to seal all joints in the vent system.

■Use caulking to seal exterior wall or roof opening around the

cap.

■The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backwardcoldairowandathermalbreakshouldbeinstalledto

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

whenusingventilationsystemswithgreaterthanspeciedCFM

ofairmovement.ThespeciedCFMvariesfromlocaletolocale.

ConsultyourHVACprofessionalforspecicrequirementsinyour

area.

Venting Methods

This range hood is factory set for venting through the roof or

through the wall. You can apply the recirculating venting method

by purchasing the Recirculation Kit.

The vent system needed for installation is not included.

A6”(15.2cm)roundventsystemisrecommended.

Roof Venting

A.6”(15.2cm)vent

through the roof

B. Roof cap

Wall Venting

A.6”(15.2cm)vent

through the wall

B. Wall cap

Recirculating

A.6”(15.2cm)vent

through the cabinet

B. Round recirculating grid

Calculating Vent System Length

Therecommendedventsystemis6”(15.2cm)roundventwitha

maximumlengthof35ft(10.7m).Forthebestperformance,use

no more than three 90° elbows.

To calculate the length of the system, add the equivalent feet

(meters)foreachoftheventpiecesusedinthesystem.

Vent Piece 6” (15.2 cm)

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

Example Vent System

90° elbow Wall cap

2ft(0.6m)

6ft(1.8m)

Maximum Recommended Length = 35 ft (10.7 m)

1-90°elbow =5.0ft(1.5m)

1-wallcap =0.0ft(0.0m)

9ft(2.8m)straight =9.0ft(2.8m)

Length of 6” (15.2 cm) system = 14.0 ft (4.3m)

WARNING

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, re, or electrical shock.

IMPORTANT: The range hood must be electrically grounded in

accordance with local codes and ordinances, or in the absence

oflocalcodes,withtheNationalElectricalCode,ANSI/NFPA70

(latestedition)orCanadianElectricalCode,CSAC22.1

No.0-M91(latestedition).

If codes permit and a separate ground wire is used, it is

recommendedthataqualiedelectricalinstallerdeterminethat

the ground path is adequate.

Electrical Requirements

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy,MA02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland,Ohio44131-5575

■ A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

 circuitisrequired.Atime-delay fuseorcircuitbreakeris also

recommended. It is recommended that a separate circuit

serving only this range hood be provided.

■This range hood is equipped with a power supply cord having

a 3 prong grounding plug.

■To minimize possible shock hazard, the cord must be

 plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility

and obligation of the customer to have the properly grounded

 outletinstalledbyaqualiedelectrician.

Installation Instructions

■The grounded 3 prong outlet is to be located inside the

cabinet above the range hood at a maximum distance of

337⁄16” (85.0 cm) from where the power cord exits the hood.

The grounded 3 prong outlet must be accessible after

installation of the range hood. See illustration.

33 7⁄16(85cm)

GROUNDING INSTRUCTIONS

■ Foragrounded,cord-connectedrangehood:

This range hood must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

This range hood is equipped with a cord having a grounding

wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

WARNING: Improper grounding can result in a risk of electric

shock.

Consultaqualiedelectricianifthegroundinginstructionsare

not completely understood, or if doubt exists as to whether

the range hood is properly grounded.

Do not use an extension cord. If the power supply cord is too

short,haveaqualiedelectricianinstallanoutletnearthe

range hood.

SAVE THESE INSTRUCTIONS

Prepare Location

■It is recommended that the vent system be installed before

the range hood is installed.

■Before making cutouts, make sure there is proper clearance

 withintheceilingorwallforventttings.

■Making the cutout to the bottom of the cabinet may be easier

to do prior to mounting the cabinet to the wall.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or non

vented.

3. Selectaatsurfaceforassemblingtherangehood.Place

covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface

Range Hood Cabinet Cutout

1. Use a saber saw or keyhole saw to cut out the cabinet

bottom inside the cabinet frame.

NOTE:Framelesstypecabinetsrequire¾”(1.9cm)frontlip

inthecabinetbottom.A¾”(1.9cm)thickllerstrip(not

supplied)mayberequiredforsometypesofcabinets.(See

Step3inthe“InstallRangeHood”section).

Cut out dimensions (without spacers)

261⁄8”(66.3cm)

107⁄8”

(27.62cm)

3⁄4”

(1.9cm)

1⁄2”

(1.27cm)

A. Bottom of cabinet cutout

2. Complete cabinet preparation following the instructions for

your type of venting. Determine venting cutout locations and

 cutoutventopeningsinthecabinets,wallsand/orsoft.

Venting Outside Through the Roof

1. Measure and mark the lines as shown. Use a saber saw or

keyhole saw to cut an opening through the top of the cabinet

and the roof for the vent.

B* C

A. Cutout

B.6¼”(15.9cm)*

C. 7¾”(19.7cm)centerlinetocabinetfront

D. Centerline

*NOTE:For12”(30.5cm)highcabinetsa6¼”deepx8”wide

(14.6cmx20.3cm)rectangularopeninginthecabinettopis

required for damper transition clearance.

Venting Outside Through the Wall

1. Installthe6”(15.2cm)venttransitiontothetopoftherange

hood liner using two 3.5 x 9.5 mm screws. Assemble the vent

 ductthatyouwilluseoverthe6”(15.2cm)venttransition.

2. Measure from the bottom of the range hood liner to the

 horizontalcenterlineoftheventopening(A)

A. Measurement A

B. Horizontal centerline of vent opening

C. Range hood liner

3. Remove the vent duct from the range hood liner.

Transfer measurement A to the cabinet back wall. Measure

from the underside of the cabinet.

4. Mark the cutout as shown. Use a saber saw or keyhole saw to

cut a round opening through the back of the cabinet and the

exterior wall for the vent. Go to Step 3.

A. Measurement A

B. Centerline

C.6¼”(15.9cm)round

cutout

Non-Vented (recirculating) Installation Through the

Soft/Cabinet

A. Ceiling

B. Vent cover

C. Soffit

D.6”(15.2cm)vent

E. Range hood

F. Cabinet

G.Wall

H.12”(30.5cm)min.cabinetheight

I.17”(43.2cm)min.ventcoverheight

1. Measureandmarkthecenterlineofthecabinettothesoft

above.

2. Measure from the bottom of the cabinet to the centerline of

 thewheretheventwillcomethroughthesoft.Markthe

location and use a saber saw or keyhole saw to cut a 5¾”

 (14.6cm)holefortheventcover.

A. Vent cover

B. Centerline

*NOTE:For12”(30.5cm)highcabinetsa6¼”deepx8”wide

(14.6cmx20.3cm)rectangularopeninginthecabinettopis

required for damper transition clearance.

Measure and mark the centerline location for the cutout in the

cabinet top. Use a saber saw or keyhole saw to cut an

opening for the vent.

ABC

A. Cutout

B. See chart below

C. 7¾”(19.7cm)center-

line to cabinet front

D. Centerline

Cabinet Height Hole Shape and Size

12”(30.5cm) A6¼”deepx8”wide(15.9cmx20.3cm)

rectangular opening in the cabinet top is

required for damper transition clearance.

Complete Preparation

1. Ifnotyetattached,installthe6”(15.2cm)venttransitionthe

top of the range hood liner using two 3.5 x 9.5 mm screws.

2. Locatesidemountingbracketush1cmtothebottomofthe

cabinet side and against the inside of the front cabinet face.

Orient the bracket depending on the width of your cabinet as

 depictedinthediagramsbelow.Drill⅛”(3mm)pilotholesin

6 places, attach a bracket using three 4.5 x 13 mm screws to

each side of the cabinet, and tighten. Additional washers in

hardware package are supplied as spacers for cabinet walls

 thinnerthan½”(13mm).

BracketOrientationfor30”(76.2cm)Cabinet

A.30”(76.2cm)cabinet

B.Screws-4.5x13mm(8)

C.Washers(optional)

D.Mountingbracket(2)(positionfor30”[76.2cm]cabinet)

Move the bracket 6⁄16”(1cm)fromthebottom

side of the cabinet

3. Install the vent system according to the method needed.

Use caulking to seal the exterior wall or roof opening.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

1. Using 2 or more people, lift the hood liner into its mounted

location. Attach with four 4.2 x 19 mm screws into the slotted

openings. Do not tighten screws.

A.Cabinet

B.Hood liner canopy assembly C.Screws-4.2x19mm(8)

2. Center the canopy in the cabinet. Align the bottom of the

canopy with the bottom of the cabinet. Install four 4.2 x 19 mm

screws into the round mounting plate openings and tighten all

 (8)mountingscrews.

3. Removethemetalgreaseltersfromthefacepanel.Seethe

“Range Hood Care” section.

Attach the face plate to the hood insert.

NOTE: If cabinet depth is greater than 12”, it is recommended

 thatthetwo1/2”metalspacersareinstalled.

Install to front and rear sides of the face plate with 3.5 x 9.5

mm screws as shown in drawing.

A.Face Panel

B.Front and rear spacer C.Screws-3.5x9.5mm(4)

Install Range Hood

A.Screws-3.5x9.5mmflat-head(4)

B.Faceplate(30”x12”[76.2cmx30.5cm]shown)

C.Cabinet(30”x12”[76.2cmx30.5cm]shown)

D.Screws-4.2x15mmtruss-head(2)

For cabinet size - 30” x 12” (76.2 cm x 30.5 cm)

Attach the 281⁄4” x 10 ¾”(71.8cmx27.3cm)facepanel(supplied

withrangehood)tothehoodlinerusingfour3.5x9.5mm

at-headscrewsandtwo4.2x15mmtrussheadscrews.

Tighten to secure.

Connect the lamp electrical connector.

Connect the Vent System

Vented Installations

1. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

Non-Vented (recirculating) Installations

1. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

2. Installcharcoallters.Seethe“Availableaccesories”section.

Complete Installation

1. Replacegreaselters.Seethe“RangeHoodCare”section.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, re, or electrical shock.

2. Plug3-prongpowercordintoagrounded3-prongoutlet

located inside the cabinet above the range hood.

3. Check the operation of the range hood fan and light. See

“Range Hood Use” section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power and check wiring connections.

NOTE:Togetthemostefcientusefromyournewrangehood,

read the “Range Hood Use” section.

This manual suits for next models

Table of contents

Languages:

Other Elisa Ventilation Hood manuals

Elisa

Elisa EPR628S1 Datasheet

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual