elink LNK-IMC208P-SFP User manual
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
1 V1.0
This quick start guide describes how to install and use the Industrial Unmanaged Optical Ethernet Switch. This is the
Switch of choice for harsh environments.
Overview
LNK-IMC208P-SFP is a unmanaged 8 ports 100Base-FX SFP + 2 ports 10 100 1000Base-T SFP Combo
Optical Ethernet Switch. The Switch provides SFP slot to support the use of SFP (Small Form-factor
Pluggable) transceiver module. User can chose different types of SFPs (1000M only). The Switch
supports 1 or 2 core Single-mode or Multi-mode fiber. The product operates at temperatures ranging from
-40
o
C to 75
o
C and
DIN-Rail installation
.
General
To ensure trouble free transportation and storage, all E-link products must be thoroughly inspected, tested
and properly packed before delivery. Check the product upon receipt for any visible damage which may
have been caused during shipment.
Package Content
Hardened 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Unmanaged Optical Ethernet
Switch x 1
Quick Start Guide x 1
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
2 V1.0
Physical Description
Front Panel Rear Panel
Installation
SFP Optical Module
You can select different SFP modules as required (Please refer to our SFP Ordering Options for the
appropriate module).
To insert remove the SFP, the procedures are as follows :
1. On the front panel, insert the SFP module into
the SFP port until it is securely locked.
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
3 V1.0
2. Connect the optical fiber (1 2 core) to the LC connector(s) of the SFP.
3. To remove the SFP module, press down the lock of the LC connector of the
optical fiber to pull out the fiber cable.
4. Pull down the SFP lever and hold its position. Pull out the SFP module
from the SFP port.
Din-rail Mounting
LNK-IMC208P-SFP can be installed on a DIN rail. Installation steps are as follows:
1. First, insert the top of DIN-Rail into the track.
2. Then, lightly push the DIN-Rail into the track.
3. Check if the DIN-Rail is tightened on the track or not.
4. To remove the industrial switch from the track, reverse steps above.
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
4 V1.0
Setup
1. Connect one end of the Ethernet cables to their corresponding ports on the product. Connect the
other end to the network equipment such as IP cameras, Switches or PCs. Insert the SFP and
connect the optical fiber cables to its connectors.
2. Connect the product with the power adapter and switch on the product, the PWR indicator should
then be ON. If it is not, please check whether the power cable is connected properly and the power
supply functions normally..
3. After all cables are correctly connected, the indicators will be lit as per port status LEDs (page 5).
Inter ace
RJ-45 Pin Assignment
1000Base-T Pins
Pin MDI MDIX
1 TP0+ TP1+
2 TP0- TP1-
3 TP1+ TP0+
4 TP2+ TP3+
5 TP2- TP3-
6 TP1- TP0-
7 TP3+ TP2+
8 TP3- TP2-
Power Connection：
：：
：
Pin
Description
V1 - V1 + V2 - V2 +
Power Input GND
+12~48V
(DC)
GND
+12~48V
(DC)
Cable Connections
Signal Type Cable Type Connector
Ethernet Cat. 5 or above RJ45
Optical SM MM Optical fiber cable (depends on SFP) LC
Power supply 1 Power cable 6-pin Terminal Block
（
Pin 1 2
）
Power supply 2 Power cable 6-pin Terminal Block
（
Pin 5 6
）
ALM UTP 6-pin Terminal Block
（
Pin 3 4
）
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
5 V1.0
LED Indicators
Indicator Color Status Description
PW1 Green ON Powered on
PW2 Green ON Powered on
ALM Green ON Power Failure or Port Down fail
G1,G2
SPD Amber
ON Operating at speed 1000M
OFF No network device is connected or not operating at speed of 1000M
LINK/ACT Green
ON A network device is connected
Blinking The connected device is transmitting or receiving data.
OFF No network device is connected
SFP Port
(P1-P8)
LINK/ACT Green
ON A network device is connected
Blinking The connected device is transmitting or receiving data.
OFF No network device is connected
Dip Switch
PW1, PW2 Power 1 and Power2 failure alarm function on off.
P1~P8 Each SFP port Link failure alarm function on off.
G1,G2 Each Giga port Link failure alarm function on off.
Dimension drawing o the unit
LNK-IMC208P-SFP
Hardened Unmanaged 8-port 100Base-FX SFP + 2-port 10 100 1000Base-T SFP Combo Optical Ethernet
Switch
6 V1.0
Functional Description
•
8 100Base-FX SFP + 2 10 100 1000Base-T SFP Combo with.
• Combo port RJ45 support 10 100 1000Mbps Full half-duplex, Auto-negotiation, Auto MDI MDIX.
• Supports external SFP.
• Supports 802.3x Flow Control.
• Support 8K MAC address.
• 1M bits frame buffer memory.
•
Supports Relay output for Power and Port failure
.
•
DIN-Rail installation.
•
Redundant Power Inputs.
• -40
o
C to 85
o
C (-40
o
F
℉
to 177
o
F) operating temperature range.
Table of contents
