Eliminator Lighting STRYKER BEAM User manual

User Manual

STRYKER BEAM

instructions herein are subject to change without notice. Eliminator Lighting logo and identifying prod-

uct names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed

includes all forms and matters of copyrightable materials and information now allowed by statutory or

judicial law or hereinafter granted. Product names used in this document may be trademarks or reg-

istered trademarks of their respective companies and are hereby acknowledged. All non-Eliminator

brands and product names are trademarks or registered trademarks of their respective companies.

Eliminator Lighting and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

Date Document

Version

Software

Version DMX Channels Notes

02/27/2023 1.0 1.0 13/19 ch. Initial Release

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of

this document may be available online.

Please check www.adj.com for the latest revision/update of this manual

before beginning installation and/or programming.

TABLE OF CONTENTS

Introduction 4

Limited Warranty (USA Only) | Warranty Registration 5

Features 6

Safety Precautions 7

Overview 8

Installation 9

Color Wheel | Gobos 13

Control Panel 14

System Menu 15

DMX Set Up 18

DMX Traits 21

Primary-Secondary Set Up 24

Maintenance Guidelines 25

Dimensional Drawings 26

Specifications 27

Unpacking: Thank you for purchasing the Stryker Beam. Every device has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the shipping carton for damage that

may have occurred during shipping. If the carton appears to have been damaged, carefully inspect your

xture for any damage and be sure all accessories necessary to operate the unit have arrived intact.

In the event that damage has been found or parts are missing, please contact our toll free customer

support number for further instructions. Do not return this unit to your dealer without rst contacting

customer support.

Introduction: The Stryker Beam is a DMX-capable, LED-powered moving head xture. It features

multiple selectable DMX channel modes, pan and tilt control, 13 colors, and 11 static gobos, among

other effects.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.americandj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

CAUTION! This device is intended for indoor use only! Do not expose to rain or moisture!

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,

please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

INTRODUCTION

LIMITED WARRANTY (USA ONLY)

1 Year Limited Warranty: The Eliminator Lighting warranty is valid for 1 year from the date of purchase. Our

1 year limited warranty covers manufacturing defects only. The serial number of your device and the place of

purchase with dated valid receipt must be submitted at time of service. The Eliminator Lighting warranty does

not cover items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty

is only valid within the United States.

To register your Eliminator Lighting product online, please click here to the ADJ Warranty Registration Page:

https://www.adj.com/portal/user/register/

WARRANTY REGISTRATION

Please fill out the enclosed warranty card to validate your purchase. All returned service items,

whether under warranty or not, must be freight pre-paid and accompanied by a return authorization

(R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be written down on a piece of paper

included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain an R.A. number by contacting our customer support team. All pack-

ages returned to the service department not displaying an R.A. number on the outside of the package

will be returned to the shipper.

FEATURES

• 1 x 100W LED

• Multiple selectable DMX channel modes

• Pan and tilt adjustment

• 13colors

• 11staticgobos

• Effectwheelwithbi-directionalrotatingprisms

• Single6-colorchip

• Adjustabledimmingandstrobing

• LCDdisplay

INCLUDED ITEMS

• Power Cable (x1)

• Omega Bracket (x1)

SAFETY PRECAUTIONS

• Maximum ambient operating temperature is 113° F (45° C)!

• DO NOT TOUCH the fixture housing during operation. Disconnect the power and allow approximately

15 minutes for the fixture to cool down before servicing.

• DO NOT shake the fixture, and avoid brute force when installing and/or operating the fixture.

• DO NOT operate the fixture if the power cord has become frayed, crimped and/or damaged. If the

power cord is damaged, replace immediately with a new one of the same power rating.

• DO NOT attempt to remove or break off the ground prong from the electrical cord. This prong is used

to reduce the risk of electrical shock and fire in the event of an internal short.

• DO NOT attempt to operate this unit if it has been damaged in any way.

• DO NOT spill water or other liquids into or on to your unit.

• Disconnect from main power before making any type of connection.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.

Allow approx. 20” (50cm) between fixture and other devices or a wall for proper cooling.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 20” (50cm)

between this device and a wall.

• DO NOT remove the cover for any reason.

• When installing fixture in a suspended enviroment, always use mounting hardware that is no less than

M10 x 25mm, and always install fixture with an appropriately rated safety cable.

• Never plug this unit in to a dimmer pack.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to the point where they exit from the unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug have been damaged.

B. Objects have fallen onto, or liquid has been spilled into, the fixture.

C. The fixture does not appear to operate normally or exhibits a marked change in performance.

D. The fixture has fallen and/or has been subjected to extreme handling.

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT

ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE

AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS

MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO

ANY WARRANTY CLAIMS AND/OR REPAIRS.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

INDOOR USE ONLY! DO NOT EXPOSE TO RAIN OR MOISTURE!

OVERVIEW

DMX

LED

Run

LED

Display

Screen

ESC

Button

Down

Button

Set

Button

3pin

DMX In

3pin

DMX Out

5pin

DMX In

5pin

DMX Out

Power

Out

Fuse

INSTALLATION

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical and construc-

tion codes and regulations.

When installing the unit, the trussing or area of installation must be able to hold at least 10 times the

weight of the unit and any attached accessories without any deformation. The unit must be secured

with a secondary safety attachment, e.g. an appropriately-rated safety cable.

Before rigging/mounting a single fixture to any metal truss/structure or placing the fixture(s) on any

surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure

or surface is properly certified to safely hold the combined weight of the fixture(s), clamps, cables, and

accessories.

Maximum ambient operating temperature is 113°F (45°C).

Fixture(s) should be installed away from walking paths, seating areas, or areas where unauthorized

personnel might reach the fixture by hand.

NEVER stand directly below the fixture(s) when rigging, removing, or servicing.

Overhead fixture installation must always be secured with a secondary safety attachment, such as an

appropriately rated safety cable that can hold at least 10 times the weight of the fixture.

Overhead mounting requires extensive experience, including calculating working load limits, knowl-

edge of installation material being used, and perodic safety inspection of all installation material as

well as the unit itself. If you lack these qualifications, do not attempt the installation yourself.

The installation should be checked by a skilled person once a year.

INSTALLATION

CLAMP MOUNTING

This fixture features attachment points for two mounting clamps on the bottom surface of the unit.

Additionally, the unit also features a safety cable loop located just below the display screen (see the

illustration below). When mounting the fixture to a truss or any other suspended or overhead instal-

lation, be sure to secure TWO appropriately rated clamps (not included) to the bracket installation

points, and attach a separate SAFETY CABLE of the appropriate weight rating to the provided safety

cable loop.

SAFETY CABLE:

ALWAYS ATTACH A SAFETY

CABLE WHENEVER IN-

STALLING THIS FIXTURE IN

A SUSPENDED ENVIRON-

MENT TO ENSURE THAT

THE FIXTURE WILL NOT

FALL IF THE CLAMP FAILS.

NOTICE: The maximum ambient operational temperature for this lighting fixture is 113˚ F (45˚ C). Do

not place this lighting fixture in an environment where the temperatures exceed this value. This will

allow the fixture to run at its best and help prolong the fixture life.

MOUNTING

CLAMP

INSTALLATION

POINT

MOUNTING

CLAMP

INSTALLATION

POINT

SAFETY

CABLE

LOOP

Table of contents

Other Eliminator Lighting Lighting Equipment manuals

Eliminator Lighting

Eliminator Lighting HD-MB40 User manual

Eliminator Lighting

Eliminator Lighting e 139 User manual

Eliminator Lighting

Eliminator Lighting MEGA HEX L PAR User manual

Eliminator Lighting

Eliminator Lighting Motion 60 LED User manual

Eliminator Lighting

Eliminator Lighting MEGA FLAT HEX PAK User manual

Eliminator Lighting

Eliminator Lighting MIN130 User manual

Eliminator Lighting

Eliminator Lighting EX-6 User manual

Eliminator Lighting

Eliminator Lighting Trio Par LED RG User manual

Eliminator Lighting

Eliminator Lighting MBDMX-PLUS User manual

Eliminator Lighting

Eliminator Lighting IKON PROFILE PLUS User manual

Eliminator Lighting

Eliminator Lighting INDY HEX PAR User manual

Eliminator Lighting

Eliminator Lighting EX-2 User manual

Eliminator Lighting

Eliminator Lighting Decor XV User manual

Eliminator Lighting

Eliminator Lighting Electro Panel 192 User manual

Eliminator Lighting

Eliminator Lighting INDY HEX PAR User manual

Eliminator Lighting

Eliminator Lighting MEGA GO PAR 64E User manual

Eliminator Lighting

Eliminator Lighting STRYKER WASH User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions