elektraLite eyeBall UV User manual
elektraLite LED
eyeBall UV
USER MANUAL
elektraLite (a division of Group One),
70, Sea Lane, Farmingdale, NY117 5, U.S.A.
T. +1 (6 1)- 96-0184. F. +1 (6 1)- 96-0190
WWW.MYELEKTRALITE.COM
1. Unpacking
Thank you for choosing the elektraLite UV fixture. or your own safety, please read this manual before
installing the device. This manual covers important information on installation and applications. Please
keep this manual for future reference.
elektraLite UV wash fixture uses 18 high powered leds, run in a balanced arrangement giving incredible
output. Please unpack the elektraLite UV carefully and check whether it was damaged in shipping.
The following item should be in the box with the fixture:-
2 part yoke
2 knobs for yoke
1 DMX 5 pin cable
1 Turnaround 3 to 5 pin cable
1 Turnaround 5 to 3 pin cable
1 IEC power cable
1 IEC jumper cable (for daisy chaining the power between fixtures)
Please handle the fixture with care at all times. Do not drop. Do not hit the front lens assembly.
2. Safety Instructions.
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this user manual. elektraLite UV is a high voltage fixture. Be careful when dealing with high
voltages.
Please read this manual. If you do not read this manual and damages occur to the elektraLite UV,
then it could void the warranty.
During shipping, the elektraLite UV may have been exposed to high temperature changes or humidity
changes. So, as a precaution, do not switch the elektraLite UV on immediately. Condensation can
damage the elektraLite UV so leave the elektraLite UV switched off until it has reached room
temperature. The elektraLite UV is an INDOOR operational fixture. Do not operate this fixture outdoors
or anywhere there is high humidity.
The electric connection must carry out by a qualified person and it is absolutely essential that the
elektraLite UV be grounded. So under no circumstances break off the ground pin on the Edison plug or
use the fixture where a ground is not present. A ground pin, like the fuse for the elektraLite UV is there
for safety.
Always disconnect the elektraLite UV from the power source, when the fixture is not in use or before
cleaning it. Only unplug elektraLite UV from the power source holding onto the Edison plug. Never pull
out the Edison plug out by just pulling on the power cord itself.
Please keep the elektraLite UV away from children and the general public. Please be intelligent and use
common sense when operating the elektraLite UV.
. General Guidelines.
elektraLite UV is a lighting fixture for professional use on stages, in clubs, theatres, churches etc.
elektraLite UV should only be operated at between 120 to 240 volts and only indoors.
elektraLite UV should not be operated 24/7 (24 hours a day; 7 days a week). elektraLite UV needs
operation breaks to ensure that it will work for a long time without problems. Please do not shake the
elektraLite UV and avoid using brute force when installing or operating it.
Please read this below. It is important to understand and realize the following:-
The lens encapsulates each of the leds. This way the maximum output is attained. However this means
that, if the fixture is dropped or the front lens assembly is struck, then it is possible for leds to be crushed.
So please exercise care and attention. This is not a par64 that can be abused at will!
When choosing the location to install the elektraLite UV, please make sure that it is not exposed to
extreme heat, moisture or dust and never install it outdoors. Make sure that the fixture has a good amount
of free space around it for air flow. Do not install it in a confined space or have insulation around the
fixture. The minimum distance between the elektraLite UV and the illuminated surface must be more
than 3 feet.
Always mount the elektraLite UV with an appropriate safety cable.
Operate the elektraLite UV only when you are familiar with the features on the fixture. Do not permit
operation by persons not qualified.
All modifications to the elektraLite UV will invalidate the warranty. There are absolutely no
exceptions.
If elektraLite UV is operated in any way different to the one described in this manual, elektraLite UV
maybe damaged and the guarantee will be void.
4. Installation
Please ensure that the elektraLite UV is hung using the appropriate "C" clamp or half cheeseboro. A
safety chain or cable should also be used as a secondary point of holding the fixture in case the clamp
comes loose. Never hang the fixture without a safety chain or cable. Make sure the Gel frame (Gel
holder) is clipped into position correctly and cannot come loose.
If you are not qualified or have any doubts about hanging the elektraLite UV then do NOT hang it.
Do not clamp the safety cable to the U bracket or clamp. That is not a secondary safety point.
A secondary safety point is any point that will adequately hold the elektraLite UV if the "C" clamp or half
cheesboro fails. Then the safety cable would be the backup and stop the fixture from falling to the ground.
So do NOT fix the safety cable to the same place that the "C"clamp is attached.
5. DMX-512 Control Connection
Connect an XLR cable to the female 5-pin XLR output of your elektraLite CP16/24 or other DMX
controller. The other end should be connected to the male 5-pin XLR input of the elektraLite UV. Then
daisy-chain out of the first elektraLite UV into the next elektraLite UV or other dmx device. Never “Y”
split the DMX connection.
If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and
output connector. Please refer to the diagram below.
1
2
3
4
5
DMX-512 connection with DMX terminator
or installations where the DMX cable has to run a long distance or is in an electrically “noisy”
environment, it is recommended that a DMX terminator is used. This helps prevent corruption of the
digital control signal. The DMX terminator is simply a 5 pin XLR plug (male) with a 120 Ω resistor
connected between pins 2 and 3. It is then plugged into the output XLR socket of the last elektraLite UV
or other dmx device in the chain. Please see illustration below.
1
2
3
4
5
Ω
120
6. Menus in the fixture.
Root Menu Sub Menu 1 Sub Menu 2
STAT (STATIC LOOK) UV 000-255
STROBE 000-255
AUTO (AUTOMATIC PROGRAMS) E ECT 1 (inbuilt program 1)
E ECT 2 (inbuilt program 2)
E ECT 3 (inbuilt program 3)
RUN DMX 512
SLAVE
ADDRESS ASSIGN DMX CHANNEL 001-512
ASSIGN ID ADDRESS 001-255
PERS (PERSONALITY) STAG(E) 1
STAG(E) 2
CHANNEL 1
SETTINGS DIMMER ( ADE CURVE) 000(O ) TO 004(LONGEST)
RESET PASSWORD REQUIRED
ANS O
AUTO
LOW
NORMAL
HIGH
KEY O
ON
7. Static Look.
The elektraLite UV can be set to a single static look quickly.
Use the Menu button to get to STAT.
Press Enter.
The next screen will read Warm 000. This is addressing the UV leds.
Use the ↑ or ↓ to increase brightness of the cool leds.
Numbers are expressed in DMX values so 0 is no output and 255 is highest output.
Press Enter to save the value.
The screen will automatically advance to the strobe function.
If the strobe function is to be in the static look, then use the ↑ or↓ to crease the value of strobes flash rate.
Press Enter to save the value.
This is the last entry and the static look is complete. Pressing the Enter key just continues around if you
need to make fine adjustments to the static look.
Do not press MENU as this will get you out to the Root directory and out of the static look.
8. Auto Programs.
In Auto Program there are three programs (or shows) in the elektraLite UV are Effect 1, Effect 2 and
Effect 3. Chose the one best suit for the venue.
To run a color or program in Auto mode use the Menu button to get to AUTO.
Press ENTER.
Use the ↑ or ↓ key to get to the program. Press Enter.
The program will start running.
9. Run.
Run allows the fixture to operate in either DMX or Slave operation.
Using the Menu button in the root menu go to RUN.
Press Enter to get to DMX mode. To get to SLAV mode use the ↑ or ↓
And press enter to save this setting.
10. Address (For DMX & ID)
DMX Address
Sets up the address for the dmx.
Using the Menu button in the root menu go to DMX
Press Enter to get into DMX and the display will read the current dmx channel.
The display will read for example DMX:
001
This means the fixture's current address is 1
To change it, use the ↑ or ↓ buttons to get to the correct address. Press Enter to save the address.
Now immediately Enter is pressed, the ID address for the fixture is shown. See below for ID address
information; otherwise press Enter to exit out and back to the Root Menu again.
ID Address
An elektraLite UV can be addressed (controlled) through the dmx or instead it can have its own unique
ID address.
There are a total of 255 different ID addresses from 001 to 255.
To set up the address for a fixture, use the Menu button in the root menu go to ID
Press Enter and then using the ↑ or ↓ buttons,to select the ID address.
Press Enter to save the address.
or the ID address to work you must chose a Personality that uses the ID. or example STAG
This allows you to access the ID address system on channel 4.
Set the DMX address to 001 for the fixture. So if ID address 123 is chosen then go to channel 4 on the
lighting board and set the level at 123. You will then be controlling only fixture(s) with ID address 123.
ID address 001 is the default and in ID address 001 all fixtures will be under control.
11. Personalities.
There are three different choices on how the fixture will operate.
What these "Personalities" do in terms of their channel assignments is detailed in the tables on page 7.
To change a Personality use the Menu button to get to PERS
Press Enter then using the ↑ or ↓ buttons go to the personality required.
Press Enter to save the Personality.
12. Settings. (Set has several Sub Menus which allow the following functions to be used).
1). Dimmer
The Dimmer function allows different Dimmer curves to be chosen. There are 5 choices.
Choice 1:- this is Dim off. The Dimmer curve is 0 which means any change in dimmer level is
instantaneous.
Choice 2:- Dim 1. The dimmer curve has the shortest fade in and fade out time.
Choice 3:- Dim 2. The dimmer curve has the 2nd shortest fade in and fade out time.
Choice 4:- Dim 3. The dimmer curve has the 3rd shortest fade in and fade out time
Choice 5:- Dim 4. The dimmer curve has the longest fade in and the fade out time.
To access the DIM function go through the Root Menu until DIMMER is found. Press Enter and then use
the ↑ or ↓ buttons to get to the DIM choice required.
2). Reset
This resets all values to their default.
Go through the Root Menu until Settings is displayed. Press Enter and then use the ↑ or ↓ buttons to get
to RESET. Press Enter. The display will have the cursor flashing across the bottom. The password needs
to be entered. The password is the following sequence using the ↑ and ↓ buttons.
↑ ↓ ↑ ↓ ↑ ↓ then press Enter once complete. The display will read OK followed by a return to the
RESET sub menu. The Menu button will need pressing to return to the Root Menu. Only once at the Root
Menu will the dmx control function once more. Please note the Reset also takes the dmx address back to
001.
1 . Fans
There are several different control options for the fans.
Auto:- The fans come on when the temperature exceeds its pre-set value.
The fan turns off when the temperature falls below its pre-set value.
High:- The fans are constantly on at a high rotational speed.
Normal:- The fans are constantly on at their normal rotational speed.
Low:- The fans are constantly on at a lower than normal level. If the leds exceed their operational pre-set
temperature level, then the output is reduced as the fans are "locked" at lower rotational speed.
Off:- The fans are sent to be O . . If the leds exceed their operational pre-set temperature level, then the
output is reduced as the fans are "locked" O .
14. Key Lock
The Key function is an access password for the fixture. The KEY can be turned O or ON which then
deactivates or activates the password.
To set the KEY LOCK on, go through the Root Menu until KEY LOCK is found. Press Enter and use the ↑
or ↓ to set the KEY LOCK to either O or ON. If the Key LOCK is turned ON then a password is
required to go into sensitive Menus and to change functions.
The password is ↑ ↓ ↑ ↓ ↑ ↓ (Up + Down + Up + Down + Up + Down) Enter.
15. DMX Channel Assignments for Personalities.
STAG1：
1 0-255 UV output…dimming
2
0-50 Linear dimmer speed（DIM=0）
51-100 Non-linear dimmer speed 1（DIM=1）
101-150 Non-linear dimmer speed 2（DIM=2）
151-200 Non-linear dimmer speed 3（DIM=3）
201-255 Non-linear dimmer speed 4（DIM=4）
STAG2:
CH DMX data unction
1 0-255 UV output…..dimming
2
0-9 STROBE
NO UNCTION
10-49 Synchronous slow flash
50-99 Asynchronous slow flash
100-149 Random slow flash
150-199 Asynchronous fast flash
200-255 Synchronous fast flash
3
0-10 NO UNCTION
11-20 AN O
21-25 AN LOW
26-30 AN HIGH
31-40 AN AUTO
41-100 NO UNCTION
101-150 E ECT 1
151-200 E ECT 2
201-255 E ECT 3
4 0 All ID operating together
1-255 Only the ID number chosen will be controlled
5
0-50 Linear dimmer speed（DIM=O）
51-100 Nonlinear dimmer speed 1（DIM=1）
101-150 Nonlinear dimmer speed 2（DIM=2）
151-200 Nonlinear dimmer speed 3（DIM=3）
201-255 Nonlinear dimmer speed 4（DIM=4）
CHANNEL 1：
1 0-255 UV output…dimming
16. Cleaning and maintenance.
Now ignoring maintenance and cleaning is very good way of creating problems "down the road" and
many companies and installations do just that. However the net result is, no matter what the fixture,
premature failure!
Changing the oil in a car most people do on a regular basis.
So with the fixtures regular maintenance it an excellent practice, if you want the fixtures to last.
So what is the maintenance for the fixture?
Clean the fan! That’s really it!
Turn off the elektraLite UV.
Using a small vacuum cleaner, suck the dust and “fur balls” out.
Do not use a can of co². That will just blast the dust and dirt everywhere!
The fans keep the LEDs cool and keep the electronics cool too.
Without the fans working efficiently and dust free, the fixtures will fail and that will be a lot more costly
than having someone vacuum the fixtures on a regular basis.
How often should the fans be cleaned? It depends on where the fixtures are; in a very dusty atmosphere
once a week. So check the fan on a regular basis, it may not need cleaned every week but a quick “visual
inspection” should be done.
The clear front plastic cover for the lenses should be cleaned so the light output is maintained. With the
elektraLite UV turned off, use only a moist lint-free cloth, and clean the plastic cover. Never use alcohol
or solvents to clean the fixture. Never spray anything onto the fixture at the front or in any place on the
fixture.
17. Technical Specification.
Operating voltage 100 – 250v
requency 50 – 60 Hertz
18 leds
80 VI
an cooled
162.5mm x 162.5mm x 218.5mm
6.5" x 6.5" x 8.6"
2.1 kgs
4.6 pounds
elektraLite is a division of Group One. Group One and its divisions are constantly improving their
product range and we reserve the right to make changes without prior notice.
Table of contents
Other elektraLite Lighting Equipment manuals
elektraLite
elektraLite LXE 700 Wash User manual
elektraLite
elektraLite MY575w User manual
elektraLite
elektraLite eyeBall IP65 User manual
elektraLite
elektraLite RGBA Dazer User manual
elektraLite
elektraLite Theatrical White Dazer User manual
elektraLite
elektraLite eyeBall Quad led User manual
elektraLite
elektraLite MY 575.3 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
