Electrolux EQAXF01BXBV User manual
EQAXF01BXBV
________________________________ ____________________________________
EN USER MANUAL 1
VN TÀI LIỆU HƯỚNG DẪN SỬDỤNG 1
Thank you for choosing ELECTROLUX. This manual contains
all the information you need to safely and correctly use your water
dispenser. Please read all the instructions prior to using the appliance,
and keep this manual in a secure place for future reference. Do not
remove the rating plate label which attached adhesive identification label
containing the code, model number, manufacturer and other information.
This label will be used by an ELECTROLUX authorized service
representative in the event that your water dispenser needs servicing.
Environmental Notice
agents.
take the appliance to the nearest WEEE collecting
agents, where available.
Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
Customer Care
12Trouble Shooting
10
d
properties incident.
To avoid danger of suffocation, keep plastic bag away from babies and children.
power
5. Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
1. This unit is designed for drinkable water only. Put bottles as specified inside
43
the cabinet before using.
3. The dispenser can satisfy the need for hot water, cold water, room
temperature water and water as a mixture of the cold water and room
temperature water.
4. With the adoption of distinctive thermal isolation technology, this unit can
minimize thermal exchange between hot, room temperature and cold water.
The heating method of machine can be only used in the lower than 1500m
elevations.
6. Regional restrictions
Do not use an extension cord or
plug adaptor.(Fig.2)
Fig. 1
Fig. 2
1. Plug the water dispenser directly into the
socket. The unit requires proper
grounding and the correct voltage (as
technical information specified on page 13
of this manual).(Fig. 1)
2. An appropriate length of power-supply cord
is provided to reduce the risks of becoming
entangled in, or tripping over a longer cord.
6. Do not place the water dispenser sitting over the
power cord.
3. Recommend to install the anti-tilt bracket at the
back side of this water dispenser to prevent
the dispenser from falling down which could
cause injury.(Fig. )6
5. Choose a place that is near a grounded
electrical socket. Keep the dispenser at least
20cm away from walls and other appliances
and furnitures on all 4 sides.
8. Use the switch when turning the heating/
cooling On/Off. Locate on the left back
side of water dispenser.(page 6)
10. Keep the unit in a dry place and away from
direct sunlight. Do not place the machine on
paper or foam. Do not place anything
flammable beside this machine.(Fig. 4)
12. Unplug the unit when the unit will not be
used for a long preiod for the reason of
saving electricity.
14. Never use organic liquids polishing chemical
to clean the machine.
15. The thermostat to control temperature has
been set up by There is nomanufacturer.
need to adjust it yourself.
Fig. 3
(Fig. 3)
Fig. 4
Fig. 5
(Fig. 5)
until the water can flow out from the hot water
spout when the hot water button be activated.
button of cold water
button of hot w
(FRONT)
ater
button of normal water
panel
spout
front carapace
condenser
power cord
drain hole
cooling switch
drip tray
heating switch
10
11
8
12
9
4
6
5
7
Fig. 6
Installing the floor Bracket kit(Fig.6)
near a grounded socket. Do not plug in power cord yet.
1. Use 13 mm screw to fix the fixing bracket on the
side of base pan.
2. Drill out a screw hole(6 mm) on the floor.
3. Insert a screw anchor (wall plug) into the drilled hole.
4. Move water dispenser, Align fixing bracket hole
with screw hole of the floor.
5. Put the 25mm screw into the screw hole of fixing
bracket.
6. Tighten the screw.
1 1 1 2-3
4-5 6
front carapace.
Fig. 7
1. Open cabinet door.
2. Place fresh bottle outside of cabinet.
3. Remove the entire plastic cap from top
of bottle.
4. Clean outside of new bottle with a cloth.
5. Place probe assembly into bottle.
6. Slide collar with head down until it clicks
in place.
7. Slide bottle into cabinet and close door.
Fig 8
.
switches
socket.
one liter
Fig. 9
approximate 12 minutes to fill the tanks
for the first time. During this period the
pump will run continuously. This is normal.
Fig
10
.
Fig
11
.
Push the red child lock button from
right to left and press hot water button
downward to start hot water flow.
After setup, it will take up to approximate
1 hour get water to maximum cold
button
button
button
button
button
Table of contents
Languages:
Other Electrolux Refrigerator manuals
Electrolux
Electrolux ER 6430 U Quick guide
Electrolux
Electrolux EI23CS55 User manual
Electrolux
Electrolux ERA 3366 X User manual
Electrolux
Electrolux LNB3AF26W0 User manual
Electrolux
Electrolux RF553 Operating manual
Electrolux
Electrolux SMS 12/6 User manual
Electrolux
Electrolux ER 2335 I Quick guide
Electrolux
Electrolux E23BC68JSS2 User manual
Electrolux
Electrolux ERN 29600 User manual
Electrolux
Electrolux ERE 39350 W User manual
Electrolux
Electrolux ERG23610 User manual
Electrolux
Electrolux ERB 3025 Quick guide
Electrolux
Electrolux ERF2000 User manual
Electrolux
Electrolux ER1532I Quick guide
Electrolux
Electrolux TG 080 N10 User manual
Electrolux
Electrolux ER 1148T Quick guide
Electrolux
Electrolux ER 9091B User manual
Electrolux
Electrolux ERN1401FOW User manual
Electrolux
Electrolux EW23SS65HS User manual
Electrolux
Electrolux Dometic RM 6270 User manual
