Electrolux EI27MO45GS User manual

MICROWAVE OVEN INSTALLATION INS UCTIONS

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

The electrical requirements for this oven are 115-120 volts AC, 15 amps or larger.

Printed in United States

IMPORTANT - PLEASE READ AND FOLLOW

Before beginning, please read these instructions completely and carefully.•

Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.•

Remove the turntable from the oven cavity.

Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.•

Do not remove permanently axed labels, warnings, or plates from the product. This may void the warranty.•

Please observe all local and national codes and ordinances.•

The installer should leave these instructions with the consumer who should retain for local inspector’s use and for•

future reference.

PARTS INCLUDED IN THE KITS

1 FRONT FRAME ASSEMBLY

QTY 1

2 BOTTOM DUCT ASSEMBLY

QTY 1

3 SCREW A 1 ⁄" LENGTH

QTY 2

4 SCREW B 1 ¾" LENGTH

QTY 4

MICROWAVE OVEN INSTALLATION INSTRUCTIONS

Refer to Illustration 1. All dimensions are in inches (cm).

Illustration 1

1. Provide an opening in the wall or cabinet as indicated

in Illustration 1. The depth should be a minimum of 20"

(50.8 cm). The oor of the opening should be constructed

of plywood strong enough to support the weight of the

microwave oven (about 100 lbs.) and should be level for

proper operation of the oven.

NOTE: While the proper functioning of the microwave

oven does not require that the opening be enclosed (with

sides, ceiling and rear partition), this may be required

by local code, and it is suggested that the local code be

checked for any such requirement.

2. Outlet should NOT be in the shaded area as indicated

on Illustration 1. At the rear of the opening, provide a

3-pronged, polarized, electrical outlet, 115-120 volt AC, 15

amp or larger.

3. Minimum required distance between the microwave oven

and the wall oven should be 2-inches.

PRODUCT DIMENSIONS

EI30M045T TRIM KIT

A B C D E F G

30" (76.2 cm) 18 ⁄" (45.9 cm) 2 ⁄" (5.9 cm) 24" (60.96 cm) 13 ⁄" (33.9 cm) 17 ¾" (45.1 cm) min. 30" (76.2 cm)

EI27M045T TRIM KIT

A B C D E F G

27" (68.6 cm) 18 ⁄" (45.9 cm) 2 ⁄" (5.9 cm) 24" (60.96 cm) 13 ⁄" (33.9 cm) 17 ¾" (45.1 cm) min. 27" (68.6 cm)

CUTOUT DIMENSIONS

min. Hmax. min. Imax. J

25 ¼" (64.14 cm) 25 ⁄" (64.5 cm) 16 ¼" (41.3 cm) 16 ⁄" (41.6 cm) min. 20" (50.8 cm)

BASIC SPECIFICATIONS

OVEN INTERIOR ELECTRICAL

REQUIREMENTS

APPROXIMATE

SHIPPING WT. MAX AMP. USAGE

WIDTH HEIGHT DEPTH OVERALL 120VAC/60 Hz (UL)

120VAC/60 Hz (CSA) 46 lbs. (20.9 kg) 1.5 KW 13.0 amps (UL)

1.50 KW 13 (CSA)

17 ⁄" (44.1 cm) 10 ½" (26.6 cm) 18 ⁄" (47.3 cm) 2.0 cu. ft.

6" (15.2 cm)

4" (10.2 cm)

installation over an electric wall

oven 2" (5.1 cm) minimum gap

Product overlap

7/8" (2.2 cm)

MICROWAVE OVEN INSTALLATION INSTRUCTIONS

BOTTOM DUCT ASSEMBLY

1. Place the bottom duct in the opening and center. When

the Bottom Duct Assembly is in the opening correctly, the

ange will be tight against the lower edge of the opening.

See Illustration 2.

Illustration 2 Illustration 3

Illustration 4 Illustration 5

SCREW A

2. Secure the Bottom Duct Assembly with the two (1 ⁄")

screws A. IMPORTANT: Secure screws to the inside

cabinet. See Illustration 3.

UNIT INSTALLATION

1. Place the oven adjacent to the wall or cabinet opening.

Plug the power cord into the electrical outlet. Carefully

guide the oven into the prepared opening. Slide the oven

on the Bottom Duct Assembly. Avoid pinching the cord

between the oven and the wall. Adjust the position of the

oven so that it will rest on the Bottom Duct Assembly, but

not fully pushed in. See Illustration 4.

2. Locate tabs on the built in trim kit to the slots on control

panel. Snap the built in trim kit into the control panel to

lock in place. See Illustration 5.

SHAPE ON

BOTTOM

MICROWAVE OVEN INSTALLATION INSTRUCTIONS

3. Push the position of the oven into the cabinet so that the

feet of the oven are tted into the recesses of the Bottom

Duct Assembly. Make sure that the kit now rests ush with

the cabinet. See Illustration 6.

Illustration 6

Illustration 7

SCREW B

4. Adjust the frame so that the gap around the top of the

door and frame is even. Pre-drill 4 holes using an ¹⁄₈" bit,

using the kit to guide the holes. Attach the built-in trim kit

frame with four screws B to the cabinet. See Illustration 7.

IMPORTANT: Install top left mounting screw rst in order

to secure proper alignment of frame to oven face.

TINS-B003MRR0

DIRECTIVES D’INSTALLATION DU FOUR À MICRO-ONDES

UN INSTALLATEUR QUALIFIÉ DOIT PROCÉDER À L’INSTALLATION ET AUX RÉPARATIONS.

IMPORTANT : CONSERVER À L’USAGE D’UN INSPECTEUR EN ÉLECTRICITÉ LOCAL.

LIRE ET CONSERVER CES DIRECTIVES POUR RÉFÉRENCE FUTURE.

AVERTISSEMENT

L’alimentation électrique pour ce four est de 115-120 volts CA, 15 ampères et plus.

Imprimé aux États-Unis

IMPORTANT - PRIÈRE DE LIRE ET DE SUIVRE

• Prièredelireattentivementtoutescesdirectivesavantdecommencer.

• VeilleràDÉBRANCHERLAFICHEdufouràmicro-ondesdelapriseélectriqueavantd’installerlagarnitureàencastrer.Retirerla

table tournante de la cavité du four.

• Lekitcomprenddespartiesmétalliques,ilfautfaireattentionlorsdelamanipulationetdel’installationpouréviteréventuelles

blessures.

• Nepasretirerdefaçonpermanentelesétiquettes,lesmisesengardeoulesplaquesxéesauproduit.Celapourraitannulerla

garantie.

• Veuillezobservertouslescodesetrèglementslocauxetnational.

•  L’installateur devra laisser ces directives au client qui devra les conserver pour l’usage d’un inspecteur local et pour

référence ultérieure.

PIÈCES FOURNIES AVEC LES KITS

1 ENSEMBLE DU CHÂSSIS AVANT

QTÉ 1

2 ENSEMBLE DU CONDUIT INFÉRIEUR

QTÉ 1

3 VIS A LONGUEUR 1 ³₁₆ po

QTÉ 2

4 VIS B LONGUEUR 1 ³₄ po

QTÉ 4

DIRECTIVES D’INSTALLATION DU FOUR À MICRO-ONDES

Voirillustration1.Touteslesdimensionssontencentimètres(po).

Illustration 1

1. Faireuneouverturedanslemuroul’armoirecomme

indiquéàl’illustration1.Laprofondeurdoitêtreau

minimumde50,8cm(20po).Leplancherdel’ouverture

doitêtreencontreplaquéassezfortpoursupporterle

poids du four et sa propre charge (environ 45,5 kg [100

lb])etdoitêtreàunniveauconvenablepourl’utilisation

du four.

NOTE: Bien que le bon fonctionnement du four ne

demandepasquel’ouverturesoitclose(aveccloisons

latérales,arrièreetplafond);lecodelocalpourraitl’exiger;

il est donc suggéré de vérier ce point.

2. LapriseNEdoitPASsetrouverdansl’aireombréecomme

indiquéàl’Illustration1.Àl’arrièredel’ouverture,installer

unepriseélectriquepolariséepourcheàtroisbroches,

115-120 volt CA, 15 A ou plus.

3. Ladistanceminimaleexigéeentrelefouràmicro-ondes

etlefourmuraldoitêtrede5,1cm(2po).

DIMENSIONS DU PRODUIT

KIT DE gARNITURE EI30M045T

A B C D E F G

76,2 cm (30 po) 45,9 cm (18 ¹₁₆ po) 5,9 cm (2 ⁵₁₆ po) 60,96 cm (24 po) 33,9 cm (13 ³₈ po) 45,1 cm (17 ¾ po) min. 76,2 cm (30 po)

KIT DE gARNITURE EI27M045T

A B C D E F G

68,6 cm (27 po) 45,9 cm (18 ¹₁₆ po) 5,9 cm (2 ⁵₁₆ po) 60,96 cm (24 po) 33,9 cm (13 ³₈ po) 45,1 cm (19 ¾ po) min. 68,6 cm (27 po)

DIMENSIONS DE LA DÉCOUPE

min. Hmax. min. Imax. J

64,14 cm (25 ¹₄ po) 64,5 cm (25 ³₈ po) 41,3 cm (16 ¹₄ po) 41,6 cm (16 ³₈ po) min. 50,8 cm (20 po)

SPÉCIFICATIONS DE BASE

INTÉRIEUR DU FOUR ALIMENTATION

ÉLECTRIQUE

POIDSAPPROX.À

L’EXPÉDITION

AMPÉRAGE MAX.

USAGE

LARGEUR HAUTEUR PROFONDEUR HORS TOUT 120V CA/60 Hz (UL)

120V CA/60 Hz (CSA) 46 lb (20,9 kg) 1,5 KW 13,0 amps (UL)

1,50 KW 13 (CSA)

44,1 cm (17 ⁄ po) 26,6 cm (10 ½ po) 47,3 cm (18 ⁄ po) 0,04 m3(2 pi3)

15,2 cm (6 po)

10,2 cm (4 po)

Installation au dessus d'un four électrique,

espacement minimal 5,1 cm (2 po).

Chevauchement

du produit

2,2 cm (7/8 po)

DIRECTIVES D’INSTALLATION DU FOUR À MICRO-ONDES

Placerleconduitinférieurdansl’ouvertureetcentrer.

Quand il est placé correctement, les brides seront

serréescontrelabordureinférieuredel’ouverture.Voir

Illustration 2

Illustration 2 Illustration 3

Illustration 4 Illustration 5

VIS A

2. Fixerl’ensembleduconduitinférieuravecdeuxvisA

³₁₆ po). IMPORTANT:Bienfixerlesvisàl’intérieurde

l’armoire.VoirIllustration3.

INSTALLATION DE L’APPAREIL

1. Placerlefourprèsdel’ouverturedumuroudel’armoire.

Brancherlecordond’alimentationdanslapriseélectrique.

Guideravecprécautionlefourassemblédansl’ouverture

préparée.Faireglisserlefoursurl’ensembleduconduit

inférieur. Éviter de pincer le cordon entre le four et le mur.

Ajusterlapositiondufouranqu’ilreposesurl’ensemble

duconduitinférieurd’évacuation,maispascomplètement

poussédansl’armoire.VoirIllustration4.

2. Mettreleslanguettesdukitdegarnitureàencastreren

face des fentes du panneau de commande. Enclencher le

kitdegarnitureàencastrerdanslepanneaudecommande

pour le verrouiller en place. Voir Illustration 5.

FORMEÀLA

BASE

ENSEMBLE DU CONDUIT INFÉRIEUR D’ÉVACUATION

DIRECTIVES D’INSTALLATION DU FOUR À MICRO-ONDES

3. Pousserlefourdansl’armoireanquesespattesentrent

danslesévidementsdel’ensembleduconduitinférieur

d’évacuation.Vérifieralorsquelekitsoitaffleurantà

l’armoire.VoirIllustration6.

Illustration 6

Illustration 7

VIS B

4. Ajusterlechâssisanquel’espacementausommetdela

porteetlechâssissoitàégalité.Percer4avant-trousavec

un foret de ¹⁄₈,àl’aidedukitpourguiderlestrous.Fixer

lechâssisdukitdegarnitureàencastreravec4visB.Voir

Illustration 7.

IMPORTANT :

Installer la vis de xation supérieure gauche

and’alignercorrectementlechâssissurlafaçadedufour.

TINS-B003MRR0

INSTRUCCIONES DE INSTALAC ÓN EL HORNO MICRO NDAS

LA INSTALACIÓN Y EL SERVICIO DEBEN SER REALIZADOS POR UN INSTALADOR CALIFICADO.

IMPORTANTE: GUARDE PARA USO DEL INSPECTOR ELÉCTRICO LOCAL.

LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.

ADVERTENCIA

Los requisitos eléctricos de este horno son de 115-120 voltios de CA, 15 amperios o más.

Impreso en los Estados Unidos

IMPORTANTE - LEA Y SIGA LAS INSTRUCCIONES

Antes de comenzar, lea estas instrucciones completa y detalladamente.•

Asegúrese de DESCONECTAR el horno microondas del tomacorriente eléctrico antes de instalar el juego de moldura para•

empotrado. Retire el plato giratorio de la cavidad del horno.

El juego incluye partes de metal por lo que debe manipularlo e instalarlo con precaución para evitar el riesgo de lesiones.•

No retire las etiquetas, advertencias o placas permanentes del producto. Esto puede anular la garantía.•

Cumpla todos los códigos y normas locales y nacionales.•

El instalador debe devolver estas instrucciones al cliente quien debe conservarlas para uso del inspector local y para•

referencias futuras.

PARTES INCLUÍDAS EN LOS JUEGOS

1 CONJUNTO DEL MARCO FRONTAL

CANT. 1

2 CONJUNTO DE DUCTO INFERIOR

CANT. 1

3 TORNILLO A 1 ³₁₆" DE LARGO

CANT. 2

4 TORNILLO B 1 ³₄ " LONGITUD

CANT. 4

INSTRUCCIONES DE INSTALACIÓN DEL HORNO MICROONDAS

Consulte la ilustración 1. Todas las dimensiones están en pulgadas (cm).

Ilustración 1

1. Haga una abertura en la pared o en el gabinete como se

indica en la ilustración 1. La profundidad debe ser de un

mínimo de 20" (50.8 cm). La supercie de la abertura debe

ser construida de madera laminada lo suficientemente

resistente para soportar el peso del horno microondas

(aproximadamente 100 libras) y debe estar nivelada para

obtener un funcionamiento adecuado del horno.

NOTA: Aunque el correcto funcionamiento del horno

no requiere que la abertura esté cerrada (con tabiques

laterales, superiores y posteriores), el código local puede

exigirlo y se sugiere revisar en el código local alguna

indicación de ese tipo.

2. El tomacorriente NO debe estar en el área sombreada

como se indica en la ilustración 1. En la parte posterior

de la abertura, debe haber un tomacorriente eléctrico de

tres clavijas polarizado de 115-120 volt CA, 15 amperios o

mayor.

3. La distancia mínima necesaria entre el horno microondas

y el horno de pared debe ser de 2 pulgadas.

DIMENSIONES DEL PRODUCTO

JUEgO DE MOLDURAS EI30M045T

A B C D E F G

30" (76.2 cm) 18 ¹₁₆" (45.9 cm) 2 ⁵₁₆" (5.9 cm) 24" (60.96 cm) 13 ³₈" (33.9 cm) 17 ¾" (45.1 cm) min. 30" (76.2 cm)

JUEgO DE MOLDURAS EI27M045T

A B C D E F G

27" (68.6 cm) 18 ¹₁₆" (45.9 cm) 2 ⁵₁₆" (5.9 cm) 24" (60.96 cm) 13 ³₈" (33.9 cm) 17 ¾" (45.1 cm) min. 27" (68.6 cm)

DIMENSIONES DE RECORTE

min. Hmax. min. Imax. J

25 ¹₄" (64.14 cm) 25 ³₈" (64.5 cm) 16 ¹₄" (41.3 cm) 16 ³₈" (41.6 cm) min. 20" (50.8 cm)

ESPECIFICACIONES BÁSICAS

PARTE INTERNA DEL HORNO REQUISITOS

ELÉCTRICOS

PESO APROXIMADO

DE EMBARQUE

CAP. MÁX. EN

AMPERIOS

ANCHO ALTURA PROFUNDIDAD TOTAL 120VAC/60 Hz (UL)

120VAC/60 Hz (CSA) 46 lbs. (20.9 kg) 1.5 KW 13.0 amps (UL)

1.50 KW 13 (CSA)

17 ³₈" (44.1 cm) 10 ¹⁄₂" (26.6 cm) 18 ⁵₈" (47.3 cm) 2.0 cu. ft.

6" (15.2 cm)

4" (10.2 cm)

Instalación sobre un horno eléctrico de

pared separación mínima de 2" (5.1 cm)

Colocación

del producto

7/8" (2.2 cm)

Other manuals for EI27MO45GS

This manual suits for next models

Table of contents

Languages:

Other Electrolux Microwave Oven manuals

Electrolux

Electrolux EI30BM60MS User manual

Electrolux

Electrolux EMG20D22B Instruction Manual

Electrolux

Electrolux EMT25207OB User manual

Electrolux

Electrolux EMS2140 User manual

Electrolux

Electrolux EMS28 20 User manual

Electrolux

Electrolux E30MO65GSS - 1.5 cu. Ft. Microwave Oven User manual

Electrolux

Electrolux EI30BM55HSB User manual

Electrolux

Electrolux EI24MO45IB User manual

Electrolux

Electrolux MQ818GXE User manual

Electrolux

Electrolux EMS2203MM User manual

Electrolux

Electrolux EI24MO45I B User guide

Electrolux

Electrolux EI30MH55GZ - 2.1 cu. ft. Microwave Oven User manual

Electrolux

Electrolux JMW1051 User manual

Electrolux

Electrolux EMS3085X User manual

Electrolux

Electrolux MCD3880EM User manual

Electrolux

Electrolux EMS 1745 User manual

Electrolux

Electrolux EVY6800AAX User manual

Electrolux

Electrolux EME 2661 Quick guide

Electrolux

Electrolux 316495083 User manual

Electrolux

Electrolux EMZ725MMK User manual

Electrolux

Electrolux EMC2895 User manual

Electrolux

Electrolux EMS2040 User manual

Electrolux

Electrolux EMG25D59EB Instruction Manual

Electrolux

Electrolux EMS 2688 User manual

Popular Microwave Oven manuals by other brands

Daewoo

Daewoo KOG-574R0S Service manual

LG MH7040SS instruction manual

Sharp

Sharp R-895(AL)M Service manual

Dometic

Dometic DOTRM13W installation instructions

Sanyo

Sanyo EM-X680 instruction manual

Sharp

Sharp R-393M quick start guide

KitchenAid

KitchenAid KMCX4510 Use and care

Smeg

Smeg S45MCX1 Instructions for use

Russell Hobbs

Russell Hobbs RHM2044 user guide

Sunbeam

Sunbeam SMW759 owner's manual

Gallet

Gallet FMOE230S instruction manual

Bosch

Bosch CEG732X.1B User manual and installation instructions

Dometic

Dometic Roadmate 230 operating manual

Samsung

Samsung SJ0396W Owner's instructions

Sanyo

Sanyo EM-P494WS Supplement of service manual

Sharp

Sharp R-240 Operation manual

Daewoo

Daewoo KOC-984T2S13 Service manual

Impecca

Impecca CM07M2 user manual