Elari NanoPods 2 User manual
USER MANUAL
Wireless Headphones
Model: NPS-2
EN | RU
2
Components and Controls
2
S M L
3
Thank you for choosing ELARI NanoPods 2.
Before operating the device, carefully read this manual and keep it
for future reference.
To take full advantage of the device and to extend its service life, it
is recommended to read the complete User Manual, available for
download: www.elari.net/support, www.help.elari.net.
The exterior and software of your device may dier from the
pictures in this manual as all illustrations are based on prototypes.
The company shall not be made liable for any damage caused as the
result of any misuse of the device.
In order to ensure the continuous improvement of our devices, we
reserve the right to implement any changes to the design, software,
and technical specications of the device, without any prior notice
to the user. Please see all up-to-date information at www.elari.net.
4
Technical Specications
Bluetooth v 5.0 +EDR+BLE+Dual mode
Bluetooth Prole A2DP, HFP, HSP, AVRCP, SPP
Supported Audio Codecs AAC, SBC
Bluetooth range from Device Up to 10 m
Frequency Range 20 Hz~20 kHz
Impedance 16Ω (@ 1 kHz)
Sensitivity (S.P.L) 90±3 dB (@ 1 kHz)
Earphone Driver Size Ø10 mm
Microphone Input Sensitivity -42 dB (±3 dB)
Battery Capacity of the
Earphones
Li-Ion 50 mAh, 3.7 V
Battery Capacity of the Case Li-Ion 250 mAh, 3.7 V
5
Playback/Talk Time Up to 4.5 hrs
Standby time Up to 80 hrs
Charging Time ~2 hrs
Weight of the Earphone 6.3 g
Weight (Earphones + Case) 42.5 g
First time use
Remove the protective lm from the device.
Before the rst use, charge the case and earphones via a USB cable for
at least 30 minutes. During this procedure, it is not recommended to
remove the earphones from the case.
Charging the Case
• Plug the case with the earphones inside to the power source using
the included micro USB cable*. The charging case LED indicator will
blink red while charging. When the case is fully charged, LED indicator
will stop blinking and switch to steady red light if plugged to the
power source.
* Power adapter is not included. We recommend to use the power
adapter with following specications: 5V, 0.5A max (e.g. ELARI
6
PowerPort). Using alternative power source (e.g. PC) instead of the
power adapter can lower the charging speed due to lower amperage.
• A fully charged earphone case can provide 4 cycles of a full charge to
the earphones if the power source is disconnected.
Charging the earphones
Check L/R markings on each earphone and plug them into the case
according to the markings. Charging will begin automatically.
Earphones’ indicators ash red while charging, charging case LED
indicator ashes steady white. If the LED indicators don’t light up
when earphones are placed in the charging case, plug the charging
case using the included micro-USB cable to the power source.
The charging case will start charging itself and the earphones
simultaneously. Charging case’s LED indicator will ash red. When
earphones are fully charged, their LED indicators will switch to white
for 1 minute and then turn o.
Turning on and pairing the earphones
Earphones automatically turn on when removed from the charging
case.
If the charging case is discharged, the earphones will have to be
turned on manually. Press and hold the multifunctional button on
both earphones for 3 seconds until you hear the voice notication
7
“Power On”in both earphones.
When turned on, earphones automatically switch into the
synchronization mode to sync themselves between each other. You
will hear «NanoPods connected» in each earphone after successful
sync, «Right channel» in the right earphone and «Left channel» in
the left earphone. After that, you will hear the «NanoPods pairing»
notication in the right earphone and the earphones will switching
into pairing with external Bluetooth device mode.
After successful syncing and connecting to an external Bluetooth
device, ELARI NanoPods 2 earphones work using TWS (True Wireless
Stereo) technology. The right earphone acts as a master device that
receives the signal from the source and then sends it to the left
earphone.
If the left earphone «ELARI NanoPods 2-L» is turned on separately,
it will enter the synchronization state awaiting the right earphone
connection for 30 seconds. If the right earphone is not found, it will
connect to the paired external Bluetooth device on itself.
WARNING: for the stereo sound to work the earphones should rstly
be synchronized between themselves by removing them from the
case. The successful synchronization will be indicated by «NanoPods
connected» sound notication in both earphones. After that, the
earphones will be ready to be connected to an external Bluetooth
device (smartphone, tablet, laptop, etc.).
8
Connecting the earphones to the external
Bluetooth device
1. Open the Bluetooth settings on your device and search for
Bluetooth devices.
2. Choose «ELARI NanoPods 2» from the list of found Bluetooth
devices.
You will hear «Pairing successful» in the right earphone upon
successful connection.
In order to force the earphones to switch to the Bluetooth pairing
mode, remove the earphones from the case, make sure that the
earphones are o, press and hold multifunctional button on
each earphone for 5 seconds until you hear «NanoPods pairing»
notication and LED indicator starts blinking white and red. Follow
steps 1-2 afterwards.
You can use each earphone as the separate mono sound device. In
order to do so, connect «ELARI NanoPods 2-L» or «ELARI NanoPods
2» to the external Bluetooth device separately (without pairing step
beforehand).
NOTE:
ELARI NanoPods 2 remember the previously connected devices. After
turning on, the earphones automatically establish connection to the
previously connected devices given that they have Bluetooth turned
9
on and the earphones are in range of the Bluetooth signal.
Upon pairing the earphones to the Android/iOS devices the battery
charge level indicator will be displayed in the status bar next to the
Bluetooth connection indicator. If both (left and right) earphones are
connected, the charge level of the right earphone will be displayed.
If the earphones run out of charge during call, the call will be
redirected to the smartphone.
Turning the earphones o
Place the earphones into the charging case* or press and hold the
multifunctional button on any earphone for 3 seconds.The earphones
will turn o and you will hear «Goodbye» in the both earphones.
*If the charging case is out of charge, the earphones should be turned
o manually.
Automatic shutdown
In order to save charge, the earphones will be automatically turned
o:
• If the earphone is not connected to another earphone or smartphone
for more than 3 minutes (for the right earphone) or more than 5
minutes (for the left earphone) and the multifunctional button is not
pressed.
• If the battery charge level is low.
10
Changing and installing ear tips
To ensure comfortable usage and best sound it is necessary to
appropriately choose the ear tip size. Try all the included ear tips and
choose the most suitable size.
To make sure that your choice is correct try to say something loudly
when wearing the earphones. Your voice should sound mued in
both ears.
1. Holding the earphone, gently pull on the edge of the installed ear
tip and remove it from the earphone.
IMPORTANT: when installing, don’t pull the ear tip with excessive
force. It can break.
2. Install the ear tip on the locking groove with is located on the
bottom side of the earphone.
3. Repeat the procedure for the second earphone.
IMPORTANT: in order to avoid damage to your ear canal do not use
the earphones without ear tips.
This manual suits for next models
1
Table of contents
Languages:
Other Elari Wireless Headphones manuals
