Ekwb Velocity User manual

USER GUIDE

2nd Revision, October 18th 2018

Velocity

CPU WATER BLOCK

This product is intended for installation only by expert users. Please

consult with a qualiﬁed technician for installation. Improper installation

may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products,

nor their installation. The following instructions are subject to change

without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure

and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

Please carefully read the manual before beginning with the

installation process!

Please remove your graphics card from the computer to assure

safest mounting process in order to prevent any possible damages

to your GPU and/or graphics card circuit board (PCB).

The EK-HFB and EK-ACF type ﬁttings require only a small amount of

force to screw them ﬁrmly in place since the liquid seal is ensured by

the rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended for

any liquid cooling system.

Do not use pure distilled water! For best results EK recommends the

use of EK-CryoFuel coolants!

Make sure to thoroughly bleed air out of your water block, or you will

not reach optimal performance!

QUICK INSTALLATION GUIDE

- 3 -

REPLACING THE JET PLATE PROCEDURE 5

INSTALLING THE WATER BLOCK 6

LGA20113 / 2066 SOCKET MOTHERBOARDS 6

LGA115X SOCKET MOTHERBOARDS 8

CONNECTING THE RGB LED STRIP (option) 10

CONNECTING THE RGB LED STRIP 10

CONNECTING THE DRGB LED STRIP 11

TABLE OF CONTENT

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY 4

WHAT IS ENCLOSED 4

SUPPORT AND SERVICE 12

SOCIAL MEDIA 12

- 4 -

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY

This CPU liquid cooling unit is pre-assembled for use with modern Intel

desktop socket type motherboards. By default (out of the box) this water

block supports the following CPU sockets:

- Intel® Socket LGA-115x

- Intel® Socket LGA-2011(-3) / 2066

WHAT IS ENCLOSED

The following items are enclosed with each EK-Velocity water block:

- EK-Velocity universal CPU water block.

- PreciseMount universal CPU mounting mechanism:

• M3 threaded thumb screws (4 pcs)

• LGA-2011 M3 threaded mounting studs (4 pcs)

• Springs (4 pcs)

• M3 threaded thumb nuts (4 pcs)

• Washers (4 pcs)

- EK-Velocity Backplate

• Backplate rubber gasket

• Backplate for Intel® LGA-115x socket motherboards

- Allen (hex) key 2.5mm

- Additional Inserts and Jet plates:

• Jet J2 (0.8mm* thick)

- Thermal Grizzly Hydronaut (EKWB 1.0g) thermal grease

- 5 -

REPLACING THE JET PLATE PROCEDURE

STEP 1

Please observe the table below to determine the optimal combina-

tion of insert and jet plate for your type of socket:

Socket Optimal Jet

LGA-115x J1

LGA-2011 J2

LGA-2066 J2

LED light is not included in all versions.

d= 1 mm

d= 0,8 mm STEP 1

Water block top

JET Plate

Gasket

Mounting plate

Copper base

Screws

LED Light

Frame

- 6 -

STEP 2

Unscrew the four M4 screws in counter-clock-wise direction from the

bottom of the water block using enclosed 2,5mm Allen key to release the

assembly, consisting of water block top and jet plate. Upon replacing the

jet plate please reassemble the water block as shown on the in STEP 1 and

STEP 2 pictures. Pay special attention to the insert orientation relative to

the copper base and water block top!

Before reassembly of the water block it is crucial that the

preformed gasket (o-ring) is placed into the gap between

the mounting plate and the water block top.

Screw the four screws back in but don’t exaggerate with the force applied.

JET

Top

STEP 2

INSTALLING THE WATER BLOCK

LGA-2011 M3

Thumb Screw

LGA-2011 M3

Thumb Screw

LGA20113 / 2066 SOCKET MOTHERBOARDS

STEP 1

Prepare the foil bag with mounting mechanism, which is enclosed

with the CPU water block delivery.

Install four (4) speciﬁc LGA-2011 M3 thumb screws into four M3

threaded stubs on the LGA-2011 socket integrated latch mecha-

nism (ILM). The screws are to be installed using no tools (i.e. pliers).

It is recommended to remove the motherboard form the

PC chassis before proceeding with installation of the CPU

water block because of the space constraint limitations of

various computer cases.

STEP 1

- 7 -

STEP 2

Cleaning the CPU: Wipe the CPU’s contact surface (by using non–

abrasive cloth or Q-tip, as shown on sample photo).

Applying thermal compound: On a clean IHS, apply a line of

thermal compound and spread it over the whole CPU heat spreader

(IHS) with a credit card or equivalent - see sample photo on left.

The layer of thermal compound must be thin and even in

thickness through the whole surface of the IHS. Too thick

application could lead to poor performance. This method

applies for Thermal Grizzly Hydronaut thermal compound

(3830046998477).

Non-abrasive

cloth

IHS

STEP 2

STEP 3

Align the water block over the mounting screws on the LGA-2011(-3)

motherboard with pre-installed CPU.

Before proceeding with the installation It is mandatory

to remove the protective foil from the backside of the

water block.

Place an enclosed compression spring and thumb nut over each M3

thumb screw. Start fastening two thumb nuts at a time, preferably in cross

pattern and do not tighten them fully until all of them are partially screwed

in. Then - using your ﬁngers only - screw in all four thumb nuts until you

reach the end of the thread.

STEP 3

Thumb nut

Coiled spring

- 8 -

STEP 4

Tighten the ﬁtting barbs in clockwise direction until the gasket underneath

is compressed.

The installation of the CPU water block is now complete.

Before proceeding with the installation It is mandatory

to remove the protective foil from the backside of the

water block.

With EK-Velocity series water blocks it is mandatory to use the port that

is nearest to the center of the water block as INLET port. Mixing the ports

may result in less than ideal thermal performance of the water block.

STEP 4

Fitting Ring

Fitting Barb

Inlet port

Outlet port

LGA115x SOCKET MOTHERBOARDS

STEP 1

If already installed, please remove the motherboard from your

computer and place it on an even surface with front facing down.

STEP 2

Preparing backplate rubber gasket

The enclosed rubber gasket is essential part of the backplate and

mounting system and must be used every time you install this water

block on your motherboard.

The rubber gasket has a partially cut inner part which

needs to be removed when installed on Intel® LGA-115x

motherboard. The rubber is held on four places and can

be peeled away with hand.

Outer part

Inner core

(removable)

STEP 2

- 9 -

STEP 3

Install backplate rubber gasket and place metal backplate for Intel®

LGA-115x socket to the back of your motherboard RIBBED SIDE

UP! (facing away from the motherboard) Align the holes on the

motherboard with holes on rubber gasket and backplate.

Make sure to orientate the rubber gasket to ﬁt past the

CPU socket ILM backplate. On certain ITX form factor

motherboards the rubber gasket may need to be trimmed

using household scissors.

Carefully rotate motherboard assembly with front side facing up

with one hand while holding the backplate and rubber in place with

the other hand.

Rubber

gasket

Motherboard

Metal

Backplate

STEP 3

STEP 4

Install four (4) M3 thumb screws onto your motherboard. It is

mandatory to put 0.7mm plastic washer underneath each of the

M3 thumb screws. Tighten the screws to the metal backplate until

you reach the end of the thread. Using tools (such as pliers) is not

recommended.

Continue installation by following the instructions on page

8 from STEP 2!

M3 Thumb

Screw

PVC

washer

STEP 4

- 10 -

CONNECTING THE RGB LED STRIP (option)

RGB LED Connector

CONNECTING THE RGB LED STRIP

STEP 1

Plug the 4-pin connector from Water block’s and Fan’s RGB LED light

to the RGB HEADER on the motherboard. The LED will work if the pin

layout on the header is as follows: +12V G R B.

Please ensure that the arrow indicated on the connector

is plugged into the +12V line as indicated on your

motherboard.

Failure to do so, will damage your motherboard or LED strip.

STEP 1

RGB Header

Table of contents

Other ekwb Computer Hardware manuals

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... User manual

ekwb

ekwb EK-FC R9-290X Manual

ekwb

ekwb EK-FC790 Guide

ekwb

ekwb EK-FB ASUS X58 Guide

ekwb

ekwb EK-Vector Radeon VII User manual

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti User manual

ekwb

ekwb EK-Loop Modulus Series User manual

ekwb

ekwb EK-FB MSI X399 GAMING RGB Monoblock User manual

ekwb

ekwb EK-FCQ6000 Manual

ekwb

ekwb EK-FC980 Manual

ekwb

ekwb EK-FC1080 GTX Ti FTW3 User manual

ekwb

ekwb EK X Series User manual

ekwb

ekwb D-RGB User manual

ekwb

ekwb SLIM 120 User manual

ekwb

ekwb EK-FC4890LT Guide

ekwb

ekwb EK-FC4890CF Guide

ekwb

ekwb EK-UNI Holder D5 V3 Manual

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... User manual

ekwb

ekwb EK-Quantum Magnitude sTRX4 User manual

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... User manual

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti User manual

ekwb

ekwb EK-Quantum Vector FE RTX 3080 User manual

ekwb

ekwb EK-FC7870 GTX Manual

ekwb

ekwb EK-FC970 GTX ACX Series Manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual

ekwb Velocity User manual

Popular Computer Hardware manuals by other brands