Ekwb EK-FB EVGA X58 LE Guide

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sample photo of EVGA X58 LE PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 6 screws on the back of

the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Northbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. One thermal pad (90x15x1 mm) and 2 (30x25x0,5) thermal

pads are enclosed with your water block. Please cut thermal pads as shown bellow.

(WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS

PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB EVGA X58 LE water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon7thofAugust,2009.

Southbridge

Northbridge

Mosfets

CPUsocket

18x4x0,5mm

75x7,5x1mm

25x25x0,5mm

18x4x1mm

12x4x0,5mm

12x4x1mm

Applythermalgreasehere.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric.

Thermal paste provides enough adhesive force for standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water block or

vice versa and attach it with enclosed screws as shown. Make sure that mounting

holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the Northbridge, and continue evenly outwards. Do not use too much pressure

screws (be very careful around Southbridge and use small amount of tightening force, since block has no standoffs. EKWB recommends

tightening screws around Southbridge in the end.), because motherboard might

bend and either cause bad contact with water block, or break

a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA X58 LE series are usually sold with

high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always

recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2,5x6 DIN7985

Please use the enclosed insulating

washers on all M2,5x6mm screws.

Fitting/barb

Spacer

Washer

Other ekwb Computer Hardware manuals

ekwb

ekwb EK-FB ASUS M6E Guide

ekwb

ekwb EK-PRO GPU WB RTX 30x0 User manual

ekwb

ekwb EK-FC580 DCII Guide

ekwb

ekwb 3831109891452 User manual

ekwb

ekwb EK-FB KIT GA Z97X-SOC Force Guide

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... User manual

ekwb

ekwb EK-FC Titan X Original CSQ Manual

ekwb

ekwb EK-FC 6970 V2 Manual

ekwb

ekwb EK-FB ASUS P7P55 KIT Guide

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB User manual

ekwb

ekwb EK-FC980 GTX Classy Manual

ekwb

ekwb EK-FB KIT GA X58 (UD7) Manual

ekwb

ekwb EK-FC980 GTX Ti XG User manual

ekwb

ekwb EK-FB ASUS ROG ZE Monoblock User manual

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB User manual

ekwb

ekwb EK-FC970 GTX ACX Series Manual

ekwb

ekwb Velocity - AMD User manual

ekwb

ekwb EK-FB ASUS Z270E Strix Monoblock Series User manual

ekwb

ekwb EK-Classic GPU Water BlockRTX 2080Ti D-RGB User manual

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series User manual

ekwb

ekwb EK-FC 5870 MSI Manual

ekwb

ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... User manual

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB User manual

ekwb

ekwb D-RGB User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual

ekwb EK-FB EVGA X58 LE Guide

Popular Computer Hardware manuals by other brands