EIP CD35 User manual

Page 1 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

HEAVY DU

CD35

DEHUMIDIFIER

USER MANUAL

Page 2 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

INTRODUCTION

Your Ebac Dehumidifier is packed in a plastic wrapper – please ensure that it is disposed of safely and where it will not

be a danger to children

Your Ebac Heavy Duty Dehumidifier is designed to help dry flooded or damp areas. Ideal where natural drying is just

too slow. Drying with a dehumidifier enables fast drying without problems assosiated with heat drying plaster, etc can

crack.

HOW YOUR DEHUMIDIFIER WORKS

Your dehumidifier draws in the moist air, cooling it to a temperature where excess moisture will condense, thereby

removing the excess moisture. This in turn dries anything in the immediate area which is damp. The moisture is

collected in the water container. The air is rewarmed and passed back approximately 2°C warmer.

OPERATING YOUR DEHUMIDIFIER

The amount of moisture removed by your dehumidifier will vary according to the conditions in which it is operating. For

example, operating in very cold temperatures will reduce water extraction levels.

The time taken to dry an area will depend on the size of area to be dried and level of moisture to begin with. To

achieve maximum benefit form your dehumidifier, you should ensure :-

a) It is permanently connected to the mains and controlled via the Humidistat

b) It is not switched off for long periods of time due to an incorrect setting of the Humidistat or because the container

is full.

c) Door to areas not to be dried are kept closed.

d) External doors and windows are kept closed as much as possible.

CONTROLS

Your dehumidifier is fitted with an adjustable humidistat and container full indicator.

SWITCHING ON YOUR DEHUMIDIFIER

Before connecting it to the mains you should ensure that the humidistat is turned fully anti-clockwise (fig A). Once

connected to the mains power, the humidistat control should be turned clockwise until you hear the unit operate (fig B)

To protect the compressor, you should allow 5 minutes between switching the dehumidifier off and on again.

Page 3 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

OPERATING THE HUMIDISTAT

The humidistat works in a similar way to a central heating thermostat, but instead of measuring temperature, it

measures the amount of moisture in the air. You may select the level of moisture you require (known as Relative

Humidity) and the unit will operate to achieve that level and then switch off.

As a general guide, the higher the setting the lower the Relative Humidity will be before the machine switches off.

Therefore the machine will operate longer to achieve this.

If the dehumidifier switches off and drying is not complete it is possible that the humidistat setting is too low and may

need increasing (fig C.). Conversely, if you no longer have condensation and the unit is still operating, then the

humidistat setting may need reducing (fig D.)

DEFROST OPERATION

At certain temperatures, the water taken freezes onto the pipes inside your dehumidifier and therefore needs to be

defrosted. This model features an automatic defrost which will clear any ice build up.

USER MAINTENANCE

EMPTYING THE WATER CONTAINER

When the water container is full an internal float mechanism will switch the unit off. This is indicated by the illumination

of the “full” light on the front control panel. The water container is at the rear of the unit. To empty the container,

carefully remove the water container. When emptied replace

PERMANENT DRAINAGE

When your dehumidifier is to be used constantly in one area, it can be fitted to drain continuously, eliminating the need

to empty the water container. Ideal when the property is to be left unoccupied.

For this you will need a length of PVC tubing, 18mm external diameter X 12mm internal diameter and a hose clip of

the same size. Disconnect your dehumidifier from the power supply before fitting permanent drainage.

Remove the water container and pass the tube through the hole in the base of the dehumidifier. Place the hose clip on

the tubing and push the tubing over the outlet on the underside of the drain tray and fasten the hose clip. DO NOT

over tighten the clip or it may crack the drain tray. The water container should not be replaced whilst the drainage kit is

in use.

USE OF PERMANENT DRAINAGE

When in use tubing should be run to a suitable drainage point, ensuring that the tube doesn’t rise above the drain tray,

otherwise flooding may occur.

Page 4 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

IF YOUR DEHUMIDIFIER FAILS TO OPERATE

1. Check that the plug is fully pushed into the socket and is switched on.

2. Check with some other electrical device that the wall socket is “live”. If it is not, contact a qualified electrician.

3. Check the fuse in the plug. If you replace the fuse, refit with a 13Amp fuse.

4. Check the humidistat control is turned clockwise.

5. Check that the water container is not full.

Should none of the above remedies work, then disconnect from the mains. Contact the help line on 01388 664400. DO

NOT attempt to repair the unit or unscrew the outer casing.

ELECTRICAL CONNECTION

If the appliance is fitted with a plug for which your socket is unsuitable, then it should be cut off and an appropriate

plug fitted.

This appliance complies with the suppression requirements of the EEC direction 82/199/EEC as embodied in

BS800:1988.

IMPORTANT:- The wires in this mains lead are coloured in accordance with the following code:-

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings

identifying the terminals in your own plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the

letter E or by the Earth Symbol or coloured Green and Yellow. The wire which is coloured Blue must be connected to

the terminal in the plug which is marked with the letter N or coloured Black. The wire which is coloured Brown must be

connected to the terminal which is marked with the letter L or coloured Red.

You must dispose of the non rewireable plug once it has been removed from the flexible cord. It is dangerous to

attempt to insert the plug into any electrical socket elsewhere in the house. If the flexible cord becomes damaged it

must be replaced by an identical cord.

CHANGING THE FUSE

Only 13 Amp fuses that are ASTA approved to BS1362 should be used.

The fuse cover must be refitted after replacement of the fuse. In the event of the fuse cover being lost or damaged, the

plug must not be used until a replacement is obtained. Replacement fuse covers, which must be coloured BLACK, are

obtainable from electrical retailers.

WARNING

–

THIS APPLIANCE MUST BE EARTHED

TECHNICAL SPECIFICATIONS

CD35

230V/50Hz/1 Phase

Height

550 mm

Width

345 mm

Depth

350 mm

Weight

26 kg

Min Operating Temperature

1 °C

Max Operating Temperature

35 °C

Water Extraction (24hrs) 32°C / 90%RH

10 l

Max Power Consumption 32°C / 90%RH

250 W

Max Running Current

2 A

Fuse Rating (UK)

13 A

Page 5 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

WARNINGS

•This appliance can be used by children from 8 years and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction

concerning use of the application in a safe way and understand the hazards involved.

•Children shall not play with the appliance.

•Cleaning and user maintenance shall not be made by children without supervision.

•If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified

person in order to avoid hazard.

•This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. The refrigeration system is

hermetically sealed.

•The Global Warming Potential (GWP) of refrigerants used in products manufactured by Ebac Industrial Products

Ltd is as follows

R134a – 1300

R407c – 1610

•For type and weight of refrigerant contained in this unit, please refer to the product data label

•Due to the high pressures within the refrigeration circuit, under no circumstances must direct heat be applied to

the evaporator coil in an attempt to remove the build-up of ice.

•No attempt should be made to cut open any part of the refrigeration circuit due to high pressures and gas

involved.

•If the unit is switched off at the mains power supply for any reason, the unit must be allowed to stand at rest for at

least three minutes before restarting.

•For correct installation and operation the unit inlet and outlet must have a clearance of 0.5M from all adjacent

surfaces and or structures.

•Do not remove the front or rear panels

•This machine should be serviced by qualified Ebac personnel or other persons having technical competence

servicing refrigeration equipment following the instructions in the Ebac service manual.

•Ebac service manuals and spares lists are available upon request by contacting your local Ebac distributor.

•Never operate the unit in a bathroom or swimming pool area

•Do not poke objects into any of the grilles on the machine.

•Do not cover or obstruct the air inlet or outlet.

•When running, the noise level of this machine is less than 70dba

•This machine complies with the electromagnetic compatibility 1992 regulations.

•This machine has been manufactured in the United Kingdom.

•Ensure this unit is protected by a 15A Circuit

Page 6 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

Page 7 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

Page 8 of 8

Drawing : - TPC204

Issue : - 5

Date : - 30/11/16

UK Head Office

Ebac Industrial Products Ltd

St Helens Trading Estate

Bishop Auckland

County Durham

DL14 9AD

Tel: +44 (0) 1388 664400

Fax: +44 (0) 1388 662590

www.eipl.co.uk

[email protected]

American Sales Office

Ebac Industrial Products Inc

700 Thimble Shoals Blvd.

Suite 109, Newport News

Virginia, 23606-2575

USA

Tel: +01 757 873 6800

Fax: +01 757 873 3632

www.ebacusa.com

[email protected]

German Sales Office

Ebac Industrial Products Ltd.

Gartenfelder Str. 29-37

Gebäude 35

D-13599, Berlin

Germany

Tel: +49 3043 557241

Fax: +49 3043 557240

www.eip-ltd.de

[email protected]

Other manuals for CD35

Other EIP Other manuals

EIP

EIP Neptune User manual

Popular Other manuals by other brands

GO Industries

GO Industries 38017 installation instructions

Cissell

Cissell 30LBCMAN2 manual

RIDGID

RIDGID K-60SP manual

Gage Bilt

Gage Bilt GB751SH-5 Original instructions

OVE

OVE SIERRA 60 installation manual

ReelCraft

ReelCraft 7800 OLB21 operating instructions

Body Armor 4x4

Body Armor 4x4 ECO-SERIES user manual

ROBLIN

ROBLIN DROP Dimensions

EMG

EMG EMG-ACB BARREL Installation information

MiniSolar

MiniSolar MT-150 Assembling Guide

Parkside

Parkside PSZ 250 B2 Operation and safety notes

ABB

ABB REM 610 Technical reference manual

Parkside

Parkside 55992 translation of original operation manual

Skyjacker

Skyjacker F250 installation instructions

IBM

IBM IBM SYSTEM Z overview

Grech Motors

Grech Motors G28 owner's manual

NOVAK

NOVAK BATTERY CARE SHEET Using

Telemotive

Telemotive blue PiraT Mini Startup guide