Eiki LC-X986 Installation and operating instructions
SP Controls Application Note
Eiki LC-X986
Revision C
I. Driver Features
1. Command Format
This device is controlled through RS-232.
2. RS-232 Commands
Power On
Power Off
Volume Up
Volume Down
Source 1 VGA
Source 1 DVI
Source 2 RGB (BNC)
Source 2 Comp Vid (BNC)
Source 2 Y,Pb/Cb,Pr/Cr
Source 3 Comp Vid (RCA)
Source 3 S-Video
Source 3 Y,Pb/Cb,Pr/Cr
Menu On
Menu Off
Adj Up
Adj Down
Adj Left
Adj Right
Enter
Auto Image
Keystone Up
Keystone Down
Zoom Up
Zoom Down
Focus Up
Focus Down
Audio Mute On
Audio Mute Off
Video Mute On
Video Mute Off
Freeze On
Freeze Off
3. Ot er Driver Features
Default Power Status Feedback
Pro ector Restart Lockout Timer (Default)
RS-232 Power Polling
95 Seconds
II. RS-232 Control Wiring
Wire RS-232 control to a male DB9 as follows
Connect male DB9 to the Eiki custom serial cable (ships with projector). Connect the adapter cable to the
projector port labeled Control Port.
Serial Adapters (for NRC only) A and B
Alternate Wiring If the serial adapter cable is unavailable, wire RS-232 control directly to a male 8-pin
mini-DIN termination as follows
Connect the control cable to the projector port labeled Control Port.
© 2002-9 SP Controls Inc. SP Controls reserves the right to modify specifications without notice at any time.
RX to 2
GND to 5
TX to 3
SP Controls
Device
Control
Cable
3 4 5
8
76
21
GND to 8
RX to 6
TX to 1
Control
Cable
SP Controls
Device
SP Controls Application Note
Eiki LC-X986
Revision C
III. Projector Configuration Information
To ensure the projector stays in sync with the control system, set the DISPLAY feature to OFF in the
projector's on screen menus. Scroll over to the menu to the SETTING menu whose first item is
LANGUAGE and toggle down to DISPLAY. De-select the DISPLAY option.
You may also wish to set POWER MANAGEMENT to OFF in the SETTING menu. By default, the
projector will shut itself off in 5 minutes in the absence of an input signal.
Note This projector takes approximately 5 seconds to switch inputs. This is not related to Panel control.
© 2002-9 SP Controls Inc. SP Controls reserves the right to modify specifications without notice at any time.
Other manuals for LC-X986
1
Table of contents
Other Eiki Projector manuals
Eiki
Eiki LC-X8 User manual
Eiki
Eiki LC-XNB2U User manual
Eiki
Eiki HDT700 User manual
Eiki
Eiki LC-WB200W User manual
Eiki
Eiki EIP-WX5000 User guide
Eiki
Eiki XGA "Diamond" Series LC-XD25 User manual
Eiki
Eiki EK-700LU User manual
Eiki
Eiki DLP Projector EIP-5000 User manual
Eiki
Eiki LC-X986 Setup guide
Eiki
Eiki Conference LC-WUL100 Installation and operation manual
Eiki
Eiki LC-SE10 Setup guide
Eiki
Eiki EIP-S200 User manual
Eiki
Eiki LC-X50 Setup guide
Eiki
Eiki LC-XGA970UE Setup guide
Eiki
Eiki EIP-WSS3100 User manual
Eiki
Eiki EK-800U User manual
Eiki
Eiki EK-100 series Troubleshooting guide
Eiki
Eiki LC-XNB2U User manual
Eiki
Eiki EK-120UK User manual
Eiki
Eiki EK-350 Series User manual
