Eiki EK-620U User manual
Warping and Blending
Manual AP
Applicable models
EK-620U,621W,625U
EK-800U,810U,811W,815U,820U
Oct., 2019
2
Contents
Preparation
1. Connection - - - - - 3
2. Projector - - - - - - - 4
3. PC (Laptop) - - - - - 5,6
Operation
・How to connect - - -7,8
・Save / Open - - -- - -9
・General - - - - - - - - 10
・Warp - - - - - - - - - - 11,12
・Edge Blending - - - -13,14
・Black Level - - - - - - 15,16,17
Preparation
1. Connection
Connect an RJ45 cable to Ethernet port on the projector and
the PC (Laptop).
<Direct connection>
<Multi connections>
3
LAN Port 102
2-1. Projector
OSD menu : SETUP >Communications> LAN
DHCP : OFF (direct connection) / ON (Multi connections)
IP Address :
Subnet Mask :
Default Gateway :
2-2. Select the Apply→YES to confirm the settings, and then
wait until finished.
<NOTE>
When a DHCP server exists in the connected network, it assigns an IP address to
the projector and the computer automatically.
If DHCP server does not exists, set up IP Address, Subnet Mask and Default Gateway
manually.
DHCP : Please check with the network administrator.
4
Do not need to change.
3-1. PC (Laptop)
Start > Control Panel > Network and Internet
3-2. Right-click on Local Area Connection, and select 【Properties 】.
5
3-3. In the Properties window, select the Networking tab, and
select 【Internet Protocol Version 4 (TCP/IPv4 ) 】.
3-4. Select 【Properties 】.
3-5. Select and following the projector IP address.
Change the any numbers
from Projector’s LAN
information.
Same as
Projector’s LAN
information
6
7
Operation
This AP provides three major functions including
【Warp 】 【 Edge Blending 】and 【Black Level 】.
・Old version AP needs to be removed before install the new one.
・This function makes user be able to operate a single projector.
Connecting Setting
1: Select 【File】→【New Multi-Function】.
2：Select Resolution
8
3：Input IP Address and press [Connect].
4：Connection is successful, icon will be changed from to
Delete Connecting projector
1：Select Icon
2：[Edit][Delete]
3：Disappear the selected Icon
9
Save / Open
Open
1: Select [File][Open]
2: Select directory and file.
3: Edit IP address and connect to the projector.
4: Click [Reconfigure]to load the settings.
Save
1: Select [File][Save]
2: Select directory and edit the file name.
<NOTE>
[Configure] button is not available after selected【Warp 】 【 Edge Blending 】or
【Black Level 】tabs, need to start over “Open” again.
10
【General 】
Projector Output Resolution (Default: WUXGA)
・Select the native resolution of the projector.
Connect Setting (Default: 192.168.0.100)
・Connect to the shown IP address.
Function Settings
・Reset All:
Reset all settings to default value.
This function is not available after pressed the 【Warp 】【Edge Blending 】or
【Black Level 】.
・Reconfigure:
It can apply saved settings from AP to projector.
The button will enable after opening a saved file and connecting to the projector
by AP.
Other manuals for EK-620U
1
This manual suits for next models
7
Table of contents
Other Eiki Projector manuals
Eiki
Eiki DLP EIP-4200 User manual
Eiki
Eiki LC-SVGA870U Setup guide
Eiki
Eiki LC-XB23 User manual
Eiki
Eiki EK-510U User manual
Eiki
Eiki EK-100 series Troubleshooting guide
Eiki
Eiki LC-XGA980UE User manual
Eiki
Eiki LC-4300U Setup guide
Eiki
Eiki LC-XG210 User manual
Eiki
Eiki PLC-XU56 User manual
Eiki
Eiki 3970A User manual
