Ehong EH-MC10-MESH-EVK User manual
Eho Ehong Technology Co.,Ltd
!
EH-MC10-MESH-EVK USER GUIDE
Features
•Bluetooth® Radio
-Fully embedded Bluetooth® v4.0 single
mode
-TX power +7dbm,-92.5dbm RX sensitivity
-128-bit encryption security
-Range up to 70m
-Integrated chip antenna
•Support Profiles
-Mesh network node
-Sensor
-Switch
•User Interface
- Firmware upgrade over the air (OTA)
- USB or two dry batteries supply
- Debug SPI interface
- RGB LED display
-Buzzer
•USB or two dry batteries supply
•Operating temperature range:
-30 °C to 80 °C
General Description
The EH-MC10-Mesh-EVK is mesh development
kit for CSRmesh.
The development board internal integration
RGB LED display, buttons, buzzer, battery hold-
er, digital Temperature Sensor , AIO interface
and debug SPI interface.
Application
Smart Home, Smart Industrial, Smart City
V1.1
Dec 18 2016
VERSION HISTORY
Confidential and Proprietary – Ehong Technology Co.,Ltd
NO PUBLIC DISCLOSURE PERMITTED: Please report postings of this document on public
Restricted Distribution: Not to be distributed to anyone who is not an employee of either
Ehong Technology Co.,Ltd or its affiliated companies without the express approval of Ehong
Configuration Management.
Not to be used, copied, reproduced, or modified in whole or in part, nor its contents revealed in
any manner to others without the express written permission of Ehong Technology Co.,Ltd.
This Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Ehong
Technologies. All other trademarks listed herein are owned by their respective owners.
© 2016 Ehong Technology Co.,Ltd. All rights reserved.
Version
Comment
V1.0
V1.1
Update the Package
Full Production Release
Content
1、Introduction 1
2、Package 1
3、Connecting up the Hardware 2
4、Using the Smartphone APP 3
4.1 Light Control Application Overview 3
4.2 Main Menu 4
4.3 Places 4
4.4 Managing Places 5
4.5 Creating a New Place 6
4.6 Areas 7
4.6.1 Creating New Areas 7
4.6.2 Configuring an Area 8
4.6.3 Controlling an Area 9
5、CSRmesh Devices 10
5.1 Adding New Devices 11
5.1.1 Detected Device List 11
5.1.2 Scanning QR Code 13
5.1.3 Setting Short Code 13
5.2 Configuring Existing Devices 13
5.2.1 Deleting a Device 14
5.2.2 Renaming a Device 14
5.2.3 Assigning Areas to a Device 14
5.2.4 Assign a Device as a Favourite 15
5.3 Controlling a Device 15
5.3.1 Lights 15
5.3.2 Thermostat and Heater Control 16
6、Settings 17
6.1 Gateway Configuration 18
6.2 Edit Gateway 18
6.3 Deleting a gateway 19
7、Consumption 20
8、Contact Information 20
1、Introduction
This is documentation helps you set up and use the CSRmesh
Development Kit for EH-MC10.
2、Package
For the mesh network testing, the following components are suggest-
ed:
3 ×EH-MC10 demo board(For LED, for Sensor, for switch is se-
lected)
1 ×SPI Programmer and SPI interface Cable
6 ×AA alkaline batteries(2 for each Target Board)
Page of 201
3、Connecting up the Hardware
it is now safe to power on the target board and connect it to the APP
of phone.
1. Remove the target board from the packaging at an approved
workstation
2. Install 2x AA batteries into battery holders on the reverse of the
board, observing the correct polarity, or use USB connect to PC for
power supply
3. Set the Power On/Off with on the Target board to the VBAT position
Page of 202
Positive
Positive
Figure 3.1: Target Board (reverse)
Power Switch(ON)
SPI Connector
USB power supply
Figure 3.2: Target Board (front)
4. Connect the Target board to the SPI programmer using the SPI cab
5. Connect the smaller connector of the cable to the SPI programmer
6. Connect the other end of the USB cable to free USB port on the
development PC
7. The device drivers reference SPI user guide
4、Using the Smartphone APP
This section describes how an android smartphone app can connect
to the Light control application running on the target board and
control the LED located in it.
An iOS version of the app also available.
4.1 Light Control Application Overview
The CSRmesh light control application allows the user to control devices
within the CSRmesh Network.
The Android application works by connecting to CSRmesh device. This
device acts as a bridge from the Android application to the rest of the
Page of 203
SPI Connector
USB Connector
Figure 3.3: SPI Programmer
CSRmesh network. The following section describes how to use the
CSRmesh Android application to control light devices that are part of a
CSRmesh network.
4.2 Main Menu
The main menu is available via the hamburger menu icon on the top
right of the application. This displays the menu options shown in
Figure 4.1. From this menu you can manage places, login to the cloud
via Facebook and control manage and set up the CSRmesh network.
4.3 Places
The current selected place is displayed on the main menu as shown in
Figure 2.1. Selecting the down arrow from the main menu displays the
configured and shared places and options to manage and create new
places as shown in Figure 4.2
Page of 204
Figure 4.1: Main Menu
4.4 Managing Places
Selecting Manage places allows you to manage existing places and
create new places to control as shown in Figure 4.3. Selecting the plus
icon allows you to create a new place to control, while selecting the
settings icon next to existing places allows you to configure an existing
place.
Page of 205
Figure 4.2: Places
Figure 4.3: Managing Places
4.5 Creating a New Place
To create a new place, select the plus icon from within Manage places
or select Create a new place from the places menu. A new place can
be defined as shown in Figure 4.4. This allows you to define the place
name, icon and color. Additionally you need to define the Network key
passphrase for this new place.
When creating a new place, you can also select to import a database
file from a previously created place using the IMPORT DATABASE
option. See Section Error! Reference source not found. for details on
sharing places.
Page of 206
Figure 4.4: Creating a New Place
4.6 Areas
Selecting the Areas option allows you to control and configure existing
areas and create new areas within the currently selected place as
shown in Figure 4.5.
4.6.1 Creating New Areas
Selecting the plus icon allows you to create a new area within to the
currently selected place. The new area can be configured as shown in
Figure 6.2.
Note:
Devices cannot be assigned until the areas has been created and
saved.
Page of 207
Figure 4.5: Areas
Table of contents
Popular Microcontroller manuals by other brands
AMS
AMS AS7261 Demo Kit user guide
Novatek
Novatek NT6861 manual
Espressif Systems
Espressif Systems ESP8266 SDK AT Instruction Set
Nuvoton
Nuvoton ISD61S00 ChipCorder Design guide
STMicrolectronics
STMicrolectronics ST7 Assembler Linker user manual
Texas Instruments
Texas Instruments Chipcon CC2420DK user manual
Texas Instruments
Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual
CYPRES
CYPRES CY14NVSRAMKIT-001 user guide
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM user guide
Espressif Systems
Espressif Systems ESP8266EX Programming guide
Abov
Abov AC33M8128L user manual
Laird
Laird BL654PA user guide