Edimax EW-7206APg User manual

EW-7206APg / EW-7206PDg / EW-7209APg

(

)

Version 2.0 / October 2006

English Version.

Before deploying the Access Point, please make sure all the PCs

in your wired network are able to obtain an IP address

automatically from the router like the figure below.

After the Access Point is deployed, you can surf the Internet /

Intranet wirelessly as show in the figure below.

Front Panel

The LED lights located on the Access Point’s front panel provide

information of the Access Point’s current status. EW-7206APg

EW-7206PDg

EW-7209APg

LED Color Status Description

Lit Power is supplied.

PWR

(Power) Green

Off No Power.

Flash Antenna is transmitting or

receiving data.

WLAN

(Wireless LAN)

Green

Orange

(EW-7209APg) Off Antenna is not transmitting

or receiving data.

On A valid link is established.

Flash It is transmitting or receiving

data.

LAN

(Link / Act) Green

Off No link is established.

Back Panel

EW-7206APg / EW-7206PDg

EW-7209APg

zAntenna Connector

This is where you connect the antenna. It is a round connector

(standard Reverse SMA).

z12 VDC

This is where you connect the power adapter.

zReset

The reset button has two functions.

1. If you want to reboot the Access Point, use a pencil tip to

press the reset button no more than 4 seconds.

2. If you press and hold the reset button for more than 4

seconds, the Access Point will reset to the factory defaults

(Warning: Your settings will be deleted and replaced with the

factory default settings).

z10/100M (EW-7206APg / EW-7206PDg )

This LAN port is where you connect the Access Point to your

Ethernet devices (switch or router).

z1. 2. 3. 4. 5. (EW-7209APg)

These LAN ports are where you connect the Access Point to

your Ethernet devices (switches or routers) or to computers.

To configure the other advanced settings of this Access Point with

advanced setting such as data encryption, please follow the

procedures to login the Access Point’s setup page.

To configure the more advanced settings from this Access Point,

such as data-encryption, please follow the procedure to login the

Access Point’s setup page.

The IP address of the Access Point is 192.168.2.1

First, assign an IP Address to the PC

Before assigning an IP address to the PC, please connect a

network cable from the LAN port of the PC to the LAN port of the

Access Point as show below.

1. Click “Start” on the task bar then select the “Control Panel” to

open it.

2. Click “Switch to Classic View” on the top left corner to see

more setting icons…

3. Find the “Network Connection” icon then Double-Click to

open the network connection settings.

4. You will see the “Local Area Connection” icon, click the icon

to highlight it, then Right-Click the mouse to open the sub-menu

and select the “Properties” to setup the IP address.

zClick and highlight the “Internet Protocol (TCP/IP)”, then click

the “Properties”

zSelect “Use the following IP address”. Enter a fixed IP

address, for example “192.168.2.10”, with a subnet mask of

“255.255.255.0” and leave “Default gateway”, “Preferred

DNS server” and “Alternate DNS server” blank then press

“OK” to close.

Second, login to the Access Point with a Web Browser

1. Open up web browser and type in 192.168.2.1 (Access Point

default IP address) to access the Access Point’s setup page.

2. A screen requesting user name and password, shown on next

page, will appear. The default user name and password are:

User Name: admin / Password: 1234

Note: It’s highly recommended to change the login settings and

keep it for future reference.

3. Enter the default user name and password, then press OK

button. You can start configuring the Access Point now.

If this Access Point will be connected to a router, please

first find out the DHCP/IP address setting of the router and

setup a suitable IP address to the Access Point. Check the

manual on the CD for more setting details.

4. After the configuration is done, please change your PC’s IP

address back to original setting either “Obtain an IP address

automatically” / “Obtain DNS server address

automatically” or “Using the following IP address” / “Use

the following DNS server addresses”. Press “OK” to close.

Finally, connect the Access Point to your router or switch.

Now you can use the wireless card in your PC to connect to the

Internet / Intranet wirelessly as shown below:

Other manuals for EW-7206APg

This manual suits for next models

Table of contents

Other Edimax Wireless Access Point manuals

Edimax

Edimax ECS1100 Series Programming manual

Edimax

Edimax EW-7208APC User manual

Edimax

Edimax IC-3210W User manual

Edimax

Edimax EW-7438RPn V2 Owner's manual

Edimax

Edimax EW-7303APn v2 User manual

Edimax

Edimax CV-7438nDM Assembly Instructions

Edimax

Edimax EW-7428HCn User manual

Edimax

Edimax SC1000 User manual

Edimax

Edimax EW-7416APn User manual

Edimax

Edimax Wireless LAN Access Point User manual

Edimax

Edimax CV-7428nS User manual

Edimax

Edimax CAP1200 User manual

Edimax

Edimax IAP1200 User manual

Edimax

Edimax EW-7301APg User manual

Edimax

Edimax BR-6208AC User manual

Edimax

Edimax EW-7206PDg User manual

Edimax

Edimax EW-7228APn User manual

Edimax

Edimax EW-7206APg User manual

Edimax

Edimax HP-8501APg User manual

Edimax

Edimax EW-7288APC User manual

Edimax

Edimax EW-7428HCn User manual

Edimax

Edimax EW-7416APn v2 User manual

Edimax

Edimax CV-7428nS User manual

Edimax

Edimax OAP900 User manual

Popular Wireless Access Point manuals by other brands

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Quick installation guide

Ubiquiti

Ubiquiti NanoStation NSM2 quick start guide

Cisco

Cisco Aironet 1550 Series Getting started guide

Aruba

Aruba IAP-335 user guide

Advantek Networks

Advantek Networks AWN-AP-54MR user manual

IP-COM

IP-COM AP355 user guide

Buffalo

Buffalo AirStation WLA-L11G user manual

EnGenius

EnGenius EnStationACv2 user manual

D-Link

D-Link DAP-3662 Quick installation guide

xG Technology

xG Technology xMax CN1300 installation guide

Widelink

Widelink ezWave WAP-1100 Series user guide

Ubiquiti

Ubiquiti LBE-5AC-Gen2 quick start guide

Aruba

Aruba AP-203R installation guide

LuXout Shades

LuXout Shades LUXSHADE MOTION manual

CreatComm

CreatComm TB5F user manual

SineDigital

SineDigital MW-1500AP(H) installation guide

TP-Link

TP-Link AP9650 V1 Quick installation guide

Draytek

Draytek VIGORAP 902 user guide