Edimax GS-5654LX User manual

GS-5654LX, GS-5654PLX V2

Quick Installation Guide

04-2023 / V1.1

Contents

I. Product Information.................................................1

I-1. Package Content ..................................................................1

I-2. Hardware Overview .............................................................2

I-3. LED Status.............................................................................3

II. Installation ..............................................................5

II-1. Physically Setup....................................................................5

II-2. Connection...........................................................................6

III.Web-based Configuration Utility ..............................8

IV. More Information..................................................10

V. Safety Instructions .................................................10

I. Product Information

GS-5654LX: 54-Port Gigabit Web Smart Switch with 6 SFP+ 10G Ports

GS-5654PLX V2: 54-Port Gigabit PoE+ Long Range Web Smart Switch with

6 SFP+ 10G Ports

I-1. Package Content

GS-5408PLG V2

Power Cord

Rack-Mount Kit

GS-5424PLC V3

Quick Installation

Guide

Console Cable

GS-5654LX or GS-5654PLX V2

I-2. Hardware Overview

GS-5654LX:

GS-5654PLX V2:

Console Port

AC Power Jack

DC Fan

SYS ALM: System Alarm LED

SYS: System LED

PWR: Power LED

Gigabit Port (1~48)

Reset Button

10 Gigabit SFP+

Port (49~54)

SYS ALM: System Alarm LED

PoE Max: Over PoE Max Power Alarm LED

Gigabit PoE Port

(1~48)

Reset

Button

Indicators Slide

Switch

SYS: System LED

PWR: Power LED

10 Gigabit SFP+

Port (49~54)

Console Port

AC Power Jack

I-3. LED Status

GS-5654LX

Function

Color

Status

Description

PWR

Green

Power on

Off

Power off

SYS

Green

Power on

Blinking

System is booting up

Off

Power off

SYS ALM

Red

System failure

Off

Device in good condition

Link/Act

(1~48 Port)

Green

Link at 1000Mbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

Amber

Link at 10/100Mbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

10 G

SFP+ Port

(49-54 Port)

Blue

Link at 10Gbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

Green

Link at 1Gbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

GS-5654PLX V2

Function

Color

Status

Description

PWR

Green

Power on

Off

Power off

SYS

Green

Power on

Blinking

System is booting up

Off

Power off

SYS ALM

Red

System failure (Overheat, wrong

voltage)

Off

Device in good condition

PoE Max

Green

Over PoE max. power

Off

Not over PoE max power

10 G

SFP+ Port

(Port 49~54)

Blue

Link at 10Gbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

Green

Link at 1000Mbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

Link/Act or PoE

Indicators

Slide Switch

Link/Act

(Left)

Show Link/Act network

connection status (Port 1 ~48)

PoE

(Right)

Show PoE connection status (Port

1~48)

Link/Act

(Left )

Green

Link at 1000Mbps

Blinking

Sending or receiving data

Off

Port disconnected or link fail

Amber

Link at 10/100Mbps

Blinking

Sending or receiving data

off

Port disconnected or link fail

PoE

(Right)

Green

Feeding power to PoE devices

Off

PoE function is not active

II. Installation

Read the following topics and perform the procedures in the correct order.

Incorrect installation may cause damage to the product.

II-1. Physically Setup

There are two ways to physically set up the switch. No matter how you

installed the switch, please keep it with good ventilation.

1. Desktop Placement: Attach the supplied rubber feet to the recessed areas

on the bottom of the switch. Place the switch on a flat surface and keep it

with good ventilation.

2. Rack-Mount Installation: You can mount the switch in any standard size,

19-inch (about 48 cm) wide rack with 1 Rack Unit (1U) of space, which is

1.75 inches (4.45 cm) high.

First, align the mounting brackets with the mounting holes on the switch’s

side panels and secure the brackets with the screws.

Then secure the switch on the equipment rack and keep it with good

ventilation.

II-2. Connection

1. Power on: Connect the power cord to the switch and the power outlet.

The switch is powered by the 100-240VAC 50/60Hz external high-

performance power supply. (Note: Make sure the PWR LED is green.)

2. Uplink: Plug the SFP/SFP+ cable into the SFP/SFP+ slot (Note: Make sure

that the LED is blue (SFP+), green or amber (SFP)) or plug the standard

Cat5e or above Ethernet cable into the LAN port (Note: Make sure that the

LED is green or amber) and connect it to another switch.

3. Connect devices: Plug the standard Cat5e or above Ethernet cable into the

LAN port and connect to any networking device with an Ethernet port.

(Note: Make sure that the "LAN" Link/Act LED is green or amber.) The

hardware installation is complete!

4. Connect a computer: Connect your computer with the switch and get

ready for web-based configuration with following “Section III Web-based

Configuration Utility”.

1. Power on

3. Connect devices

2. Uplink to another

switch

4. Connect to

a computer

III.Web-based Configuration Utility

This section describes how to navigate the web-based switch configuration

utility through web browser. Be sure to disable any browser pop-up blocker.

Browser Restrictions

If you are using older versions of Internet Explorer, you cannot directly use

an IPv6 address to access the device. You can, however, use the DNS

(Domain Name System) server to create a domain name that contains the

IPv6 address, and then use that domain name in the address bar in place

of the IPv6 address.

If you have multiple IPv6 interfaces on your management station, use the

IPv6 global address instead of the IPv6 link local address to access the

device from your browser.

Launching the Configuration Utility

1. Connect your computer with the switch then open a web browser.

2. Enter the IP address of the switch you are configuring in the address bar

on the browser (factory default IP address is 192.168.2.1) and then press

Enter. Please make sure that your computer's IP address is in the same

subnet as this switch. The default IP address is an IP address in the range

of 192.168.2.X (X=2-254). You can modify the IP address of your computer

if you need.

Default IP

192.168.2.1

Default User Name

admin

Default Password

1234

Other manuals for GS-5654LX

This manual suits for next models

Table of contents

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual