Edimax EU-HB4S User manual
USB 2.0 Slim HUB
Version 1.1
Contents
1.0 Introduction ………..…………………………….P.2
2.0 Features ……………….………………………….P.2
3.0 Specification ………………………………………..P.3
4.0 Installation …………...…………….………….…….P.3
- 1 -
USB 2.0 Slim HUB User's Manual
1.0 Introduction
This is designed in accordance to USB specification Rev 1.1/2.0 which act as a bridge
between the main computer host and the down stream USB devices. It is able to complement
PC serial interface by connecting a full range of peripherals, which is very simple and flexible
for the users.
There is one upstream port that connects to the PC host and there are four down steam ports
connecting up to 127 USB devices in a tiered-star configuration. It supports both full speed
(480M bps) and low speed (1.5M bps) devices which include keyboards, mice, scanner.
It is also protected by automatic per-port over-current detection and recovery and the LED
indicating the connection status and power source.
2.0 Features
zFull compliance with USB specification Rev. 1.1.
zWith one up-stream port and four down-stream ports.
zConnects up to 127 devices in a tiered star configuration.
zSupports both full-speed (12M bps) and low-speed (1.5M bps) devices.
zSelect between self-powered mode and bus-powered mode automatically.
zPer port over current detection/protection and power switch control.
zLED for bus-power, self-power and four down-stream connection status.
LED light
DC Jack
USB port
- 2 -
3.0 Specifications
-Upstream port 1
-Downstream port 4
-LED: 4 for BUS Power status when device connect.
The “GREEN” light is power .
The “RED” light is for USB 2.0 high speed.
-Enclosure: Plastic
-Per port Output current: 500mA
-Operating temperature: 0 degrees to 40 degrees
-Storage temperature: -20 degrees to 60 degrees
-Humidity: 0% ~ 80% RH
-Power Adapter 1.5 A , 6 V , 2.0 mm , out “ – “ , inside “ + “
4.0 Installation
1. Plug the DC plug into the DC jack and plug the AC adaptor into an electrical outlet.
Please check the electrical out let has the same voltage as the hub adaptor.
2. Plug Connector A into the USB port of host computer.
3. Plug Connector B into the upstream port of the hub.
4. Plug all the devices into downstream port of the hub.
5. When the hub is connected to the computer, the LED lights will sparkle.
- 3 -
Table of contents
Other Edimax Switch manuals
Edimax
Edimax ES-3124RE+ User manual
Edimax
Edimax ES-5808P User manual
Edimax
Edimax EK-PA2C User manual
Edimax
Edimax ES-5804PH User manual
Edimax
Edimax ES-3316P User manual
Edimax
Edimax EU-HB4M User manual
Edimax
Edimax SP-1101W User manual
Edimax
Edimax ES-5424P User manual
Edimax
Edimax ES-3116RE+ User manual
Edimax
Edimax EK-PAK2 User manual
Edimax
Edimax EK-2U2CA User manual
Edimax
Edimax EK-PS2P User manual
Edimax
Edimax ES-3305P User manual
Edimax
Edimax EK-16RE User manual
Edimax
Edimax EK-PAK4 User manual
Edimax
Edimax ES-3305P V3 User manual
Edimax
Edimax ES-5224RM User manual
Edimax
Edimax ES-5800D+ User manual
Edimax
Edimax ES-5500G V2 User manual
Edimax
Edimax ER-5397P User manual
