Edimax ES-5500P User manual

Other manuals for ES-5500P

1

This manual suits for next models

1

Table of contents

Other Edimax Switch manuals

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

1

1Physical Description

(1) Panel

Power LED

1000/100/10Mbps LED

Link/Activity LED

RJ45 Connectors

Power Connector

5-Port

Power LED

Link/Activity LED

8-Port

1000/100/10Mbps LED

RJ45 Connectors

Power Connector

Figure 1-1 Panel description

(2) LED

Table 1-1 LED description

Power is supplied

No power

LED Color Status Description

PWR

(Power) Green Lit

Off

A valid link is established

No link is established

Data packets received

Green

LNK/ACT

(Link/Activity) Green

Lit

Off

Off

This port runs at 10Mbps

This port runs at 100Mbps

Flash

5/8 Port Gigabit Switch

SPEED

(10/100/1000M) Yellow This port runs at 1000Mbps

2

2Installation

1. Operating Environment

This switching hub must be installed and operated within the limits of

specified operating temperature (32-1310F) and humidity (10-95%

Noncondensing). Do not place objects on top of the unit. Do not obstruct any

vents at the sides of the unit. Do not position the unit near any heating source

such as heater, radiator, or direct exposure to sun. Prevent entering of water

and moisture into the unit. If necessary, use dehumidifier to reduce humidity.

2. Connecting to network devices

The RJ-45 ports on the switch support Auto-MDI/MDI-X function which

allows using straight-through or cross-over type cables to connect this switch

to workstation or hub.

Connect one end of the network cable to the RJ-45 port on the rear panel, and

connect the other end of the network cable to the RJ-45 port on the network

device. Follow the same procedure to connect all the RJ-45 ports of the

switch. The UTP network cables must comply with EIA/TIA 568

specifications and Category 5 standard for 1000Mbps data transmission.

Maximum length, using UTP cable, between the switch and connected device

is 100 meters (300ft). Once the network cable is connected to both ends and

the attached network device is powered on, the green LNK/ACT LED should

be lit.

3. Connecting the power

Connect the output end of the power

adapter to the power connector on the

rear panel of the unit. Connect the

power adapter to the power outlet.

The green Power LED on the front

panel should be lit. Figure 2-1 Connect the power adapter

External Power Adapter

3

3Trouble-shooting

1. Power LED is not lit

zCheck if the power cord is properly connected to the external power

adapter and the power outlet. Make sure the power jack is firmly

plugged into the power socket of the switch.

2. Link/Activity is not lit when connect to 1000/100Mbps device

zCheck the power switch of the network device attached to the switch;

make sure it is turned ON.

zCheck the network cable; make sure it is properly connected to the

switch and the network device.

zCheck the network cable; make sure the UTP cables comply with

EIA/TIA 568 and Category 5 specification.

[!] Contact your dealer if problem persist.