Edimax ER-5390P User manual

8-Port UTP +1-Port BNC

10Mbps Hub

ER-5390P

User’s Manual

FCC Class B Certification

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including

interference that may cause undesired operation.

Warning! This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from the one which the receiver is connected to.

• Consult the dealer or an experienced radio/TV technician for

help.

You are cautioned that changes or modifications not expressly

approved by the party responsible for compliance could void your

authority to operate the equipment.

1.Introduction

Congratulations on purchasing Edimax’s high-performance 9-

Port Desktop Ethernet Hub. Featuring ease of installation, this hub

helps hook your PCs together at a minute, communicating instantly

over the net to share resources of your PCs and Printers.

With eight UTP ports and one BNC port located at the rear

panel, this device allows you to network up to at least nine

workstations in a standalone configuration. An uplink function is

designed for connection to another hub to extend your segment,

rather than a normal port for a workstation. For more details about

Uplink function, refer to the following section.

Running at 10Mbps with great stability, ER-5390P complies

with IEEE802.3 standard. Additionally, it is noted that all end-node

devices must be within 100 meters of the connected hub.

Up to 100m

POWER 10MCOL

100MCOL 100M

LNK/ACT

8-Port

Dual Speed Hub

10/100Mbps

321 45678

POWER 10MCOL

100MCOL 100M

LNK/ACT

8-Port

Dual Speed Hub

10/100Mbps

321 45678

POWER 10M COL

100MCOL 100M

LNK/ACT

8-Port

Dual Speed Hub

10/100Mbps

32145678

Up to 100m

2.Features & Specifications

(1) Features

 IEEE 802.3 compliant (10Mbps, CSMA/CD)

 Provide one slide switch to select Port 1 to uplink mode

or normal mode

 Provide one BNC port for thin Ethernet (10Base2)

 Port auto-partitioning and reconnection to facilitate

faulty segment isolation

 Data collision and jabber handling functions

(2) Specifications

 Standards : IEEE 802.3

 10Mbps Ports : RJ-45 x 8 + BNC x 1

 Uplink Port : Slide Switch x 1

 Hub LED : Power, Collision

 Port LED : Link/Activity

 Dimension : 30 x 187 x 100 mm / 1.18 x 7.36 x 3.94 in.

 Weight : 260g / 0.57lb.

 Power : 7.5VAC, 0.5A External Power Adapter

 Operating Temperature：32-131°F(0-55°C)

 Operating Humidity : 10-95% (Noncondensing)

 Emission : FCC Class B, CE Mark, C-tick

3.Package Contents

 One Ethernet Hub

 One External Power Adapter

 User’s Manual

POWER

COL

LNK/ACT

9-Port Ethernet Hub 321 4 5 6 7 8

10Mbps

4.Physical Description

(1) Panel

(2) LED

LED Status Description

Number of LED

Lit Power is supplied

Power

Off No Power

One for the

whole Hub

Lit

Collision is

detected in this

segment

COL

Off No Collision

One

Lit A valid link is

established

Flash Data packets

received

LNK/ACT

(Link/Activity)

Off No link is

established

One for each port

POWER

321 4 5

Power LED Link/Activity LED

Collision LED

Power Connector

RJ-45 Connectors

BNC Port

9-Port Ethernet Hub

678

10Mbps

8-Port UTP+1-Port BNC

5.Installation

(1) Operating Environment

ER-5390P must be installed and operated within the limits of

specified operating temperature and humidity (see previous section

under Specifications). Do not place objects on top of the unit. Do

not obstruct any vents at the sides of the unit. Do not position the

hub near any heating source such as heater, radiator, or direct

exposure to sun. Prevent entering of water and moisture into the unit.

If necessary, use dehumidifier to reduce humidity.

(2) Connecting network devices

Connect one end of the network cable to any of the RJ-45 or

BNC connectors on the rear panel, and connect the other end of the

network cable to the network device with RJ-45 or BNC connector

and the maximum length between the hub and any network devices

UTP is 100 meters (300ft) and BNC is 200 meters (650ft). Once the

network cable is connected on both ends and the attached network

devices are powered on, the Link Status LED should be lit.

(3) Uplink to Another Hub

The Uplink function is designed to extend your segment by

connecting to another hub. Note that the Ethernet Hub’s port 1 can

be switched to an uplink function by switching the sliding switch.

There are two ways for you to connect to another hub:

1) Switch the sliding switch to the uplink mode to convert port 1 to

an uplink and use a straight-through twisted-pair cable to

connect port 1 to another hub.

2) If you use a crossover cable to connect the two Hubs, then you

can use any port on the Ethernet Hub to connect to any normal

port on the other Hub. Please note: the uplink port must be in

normal mode for the method to work.

(4) Connecting the power

Connect the output end of the power adapter to the power

connector on the rear panel of the hub. Connect the power adapter to

the power outlet. The green Power LED on the front panel of the

hub should be lit.

6. Trouble-shooting

1. Power LED is not lit

 Check if the power adapter is properly connected to the power outlet.

Make sure the DC power jack is firmly plugged into the power socket of the

hub.

2. Link Status LED is not lit

 Check the power switch of the network devices attached to the hub;

make sure they are turned ON. Check the network cables; make

sure they are properly connected to the hub and the network devices.

 Check the network cables; make sure the cables comply with

EIA/TIA 568 specification. Use straight-through Category 3, 4 or 5 cables

for connection.

3. The first port’s Link Status LED is not lit when it is uplinked to

another hub

 Make sure the cable is connected to the uplink port.

 Check the network cable; make sure it is properly connected to

both hubs. One end of the cable should be connected to the uplink port

while the other end of the cable should connect to a regular port. Do not

connect the cable to both uplink ports.

 Check the network cable; make sure the cable complies with

EIA/TIA 568 specification.

4. Collision LED flashes constantly

 Remove all the network cables; connect the cables back one by one

to isolate the source of the collision.

 Check the network cable, inferior cable quality will result in

excessive collision and error packets.

[!] Contact your dealer if problem persist.

Table of contents

Other Edimax Switch manuals

Edimax

Edimax ES-3116RL User manual

Edimax

Edimax ES-516G+ User manual

Edimax

Edimax EK-08RE User manual

Edimax

Edimax GS-1026 User manual

Edimax

Edimax EU-HB4M User manual

Edimax

Edimax ES-5224RM User manual

Edimax

Edimax EK-082C User manual

Edimax

Edimax 16 Port Nway Fast Ethernet PoE Web Smart... User manual

Edimax

Edimax 9-Port Desktop Ethernet Hub ER-5390S User manual

Edimax

Edimax Two-console 16 port PS/2 KVM Switch User manual

Edimax

Edimax EU-4306 User manual

Edimax

Edimax ES-5224RM+ User manual

Edimax

Edimax GS-1008PH User manual

Edimax

Edimax ES-5816PHG User manual

Edimax

Edimax EK-PSK4 User manual

Edimax

Edimax GS-3008P User manual

Edimax

Edimax EK-08RE User manual

Edimax

Edimax ES-5500G User manual

Edimax

Edimax SP-1101W User manual

Edimax

Edimax ES-1016 User manual

Edimax

Edimax ES-5500G User manual

Edimax

Edimax ES-5226RM User manual

Edimax

Edimax ES-1024 User manual

Edimax

Edimax EU-PC2C User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual