Edimax EN-9235TX-32 User manual

Other manuals for EN-9235TX-32

3

Table of contents

Other Edimax PCI Card manuals

Popular PCI Card manuals by other brands

ERMA

ERMA SSI 1417 instruction manual

SIIG

SIIG CyberSerial Dual PCI Software installation

Moxa Technologies

Moxa Technologies CP-102E Quick installation guide

I-Bus

I-Bus IBC2602 user guide

Exsys

Exsys EX-60102 manual

Chelsio Communications

Chelsio Communications T5 Series Installation and user guide

Conrad Electronic

Conrad Electronic 97 46 71 operating instructions

Micro Innovations

Micro Innovations USB650A Quick installation guide

KTI Networks

KTI Networks KF-310 user guide

Asus

Asus SpaceLink WL230 user manual

SIIG

SIIG SC2475 Quick installation guide

TRENDnet

TRENDnet TEW-703PI Quick installation guide

Belkin

Belkin F5D7000F user manual

Pericom

Pericom PI7C7100 manual

ADLINK Technology

ADLINK Technology cPCI-3548 user manual

Digium

Digium TE200 Series user manual

Allo.com

Allo.com 2nd Gen E1/T1/J1 Quick installation guide

Western Digital

Western Digital FireWire PCI Adapter installation guide

FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference

at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received;

including interference that may cause undesired operation.

CE Mark Warning

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class B for ITE, the essential protection requirement

of Council Directive 89/336/EEC on the approximation of the laws of the

Member States relating to electromagnetic compatibility.

Edimax has an on-going policy of upgrading its products and it may be

possible that information in this document is not up-to-date. Please check for

the latest information at www.edimax.com. No part of this document can be

copied or reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective

companies.

Copyright © 2009. All Rights Reserved.

1. Introduction

Thanks for purchasing the Edimax EN-9235TX-32 Gigabit Ethernet PCI adapter. This manual

describes the steps to follow when installing the hardware and software that came with the

product. The EN-9235TX-32adapter supports 10BASE-T, 100BASE-TX and 1000BASE-T

Ethernet copper interface. Moreover, the PCI interface on the EN-9235TX-32 complies with

PCI Local Bus, and is compatible with 32-bit PCI bus. As a bus master, the EN-9235TX-32

requests access to the PCI bus, instead of waiting to be polled.

1.1 Features

The EN-9235TX-32 Gigabit Ethernet PCI adapter is a cost effective, high-performance

network interface card. It operates in 10BASE-T, 100BASE-TX and 1000BASE-T modes and

integrates easily with Fast Ethernet hub and Gigabit hub and switches.

yComplies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, and IEEE 802.3ab

1000BASE-T standards

yComplies with PCI specifications

ySupports 32-bit bus master for high throughput and low CPU utilization

ySupports both Half and Full Duplex operations

ySupports 10/100/1000Mbps auto-sensing capability

ySupports Wake On LAN (depending on the model and the user’s motherboard function)

yRich diagnostic LED mounted on bracket for easy viewing and troubleshooting (Link/Act

Green/Blinking Green)

yPlug-and-Play Installation

yNetwork drivers on CD for Windows 98SE, 2000, XP, Vista, MAC 10.4x up and Linux driver

yFCC, CE class B certified

1.2 System Requirements

Before using the adapter, you need the following components:

yOne 32 or 64 bit PCI master mode expansion slot that is compliant with PCI bus

specifications

yOne CD-ROM drive

yThe following cables:

Port Type Media Max. Distance

10BASE-T Cat. 3, 4, or 5 UTP 100 meter

100BASE-TX Cat. 5 or 5e UTP 100 meter

1000BASE-T Cat. 5 or 5e UTP 100 meter

NOTE: 1000BASE-T signaling requires four twisted pairs of Category 5 balanced cabling, as

specified in ISO/IEC 11801:1995 and ANSI/EIA/TIA-568-A (1995) and tested for

additional performance using testing procedures defined in TIA/EIA TSB95.

2. Unpacking and Inspection

Caution:

Under ordinary circumstances, this adapter card will not be affected by static charge as may

be received through your body during handling of the unit. In special circumstances where

you may carry an extraordinarily high static charge, it is highly recommended for you to

reduce the charge by touching a ground before handling the adapter card.

Open the shipping gift box and carefully remove all items. Please check the following items:

yOne EN-9235TX-32 Gigabit Ethernet PCIAdapter

yOne driver/manual CD

3. Installing the Adapter

1. Turn off the computer.

2. Remove the computer’s cover in accordance to its manual.

3. Insert the contact edge of the adapter card into the connector of any available PCI Bus

master expansion slot. Press the card firmly into the connector to PCI slot. Please make

sure that the card’s contacts are fully seated in the PCI slot.

4. Install the bracket screw that secures the card to the computer chassis.

5. Replace the computer’s cover.

6. Connect the CAT3 or CAT5 UTP cable to the RJ-45 network connector.

7. Remove driver CD from the PC’s CD-ROM drive.

8. Turn on the computer.

9. If the BIOS section of your computer’s boot program is Plug-and-Play compliant, then at

power up the BIOS will automatically configure any newly installed adapter.

Note:

Due to some Plug-n-Play BIOS programs' problem, a newly installed adapter, may

occasionally be assigned an interrupt number that is already used by another device adapter.

In such case, the conflict of interrupt number will cause faults in the behavior of both devices.

Therefore it is necessary to run the CMOS Setup utility, and manually assign a non-conflict

Interrupt Number.

4. Driver CD

The diver CD contains all the popular operating system drivers such as:

yWindows 98SE/ME/NT4.0/2000/XP/Vista

yMAC OS 10.4x and up

yLinux

yNovell Netware 4.X/5.X/6.X

Note:

If any of the listed items are missing, please contact your distributor or reseller.

5. Software Installation

After mounting this adapter to your computer, you have to install a driver to

activate this adapter. The following instruction uses Windows XP as the

presumed operation system. The screens upon installation differ slightly from

each operation system but the procedures are familiar. Please refer to the

following for instructions.

1. Turn your computer on after plugging the EN-9235TX-32 to a PCI-E slot.

When the “Found New Hardware Wizard” pops up, click the “Cancel”

button to close the window.

2. Insert the Driver CD into your CD ROM drive. The Setup Wizard will run

automatically and display the following screen. Select EN-9235TX-32 by

clicking on its product icon.

3. On the following screens, choose Setup Driver and select your operating

system.

4. When the Welcome window pops up. Click the “Next” button to start

driver installation.

5. On the following screen, click Install.

6. Please wait while driver is being installed.

7. Click the “Finish” button to complete driver installation.

Note:

Driver installation details for MAC OS and Linux are in their respective

folders. Please use your File Manager to locate and browse the CD contents

for instructions.