Edelbrock Qwikdata 91195 User manual

Rev. 6/03

Edelbrock Corporation, 2700 California Street, Torrance, CA 90503

Tech Line: 800-416-8628; Office: 310-781-2222

Edelbrock Qwikdata Shaft Speed Sensor Kit

Catalog # 91195 & 91196

INSTALLATION INSTRUCTIONS

•PLEASE study these instructions carefully before installing your new Edelbrock Qwikdata Shaft Speed Sensor Kit. If you have any

questions or problems, do not hesitate to contact our Technical Hotline at: 1-800-416-8628, from 7am-5pm, Monday through

Friday, Pacific Standard Time, or via e-mail at: [email protected].

•DESCRIPTION

The Edelbrock Qwikdata Shaft Speed Sensor Kit allows users

of the Qwikdata data aquisition system or other data

aquisition systems to mount up to 4 magnets in an aluminum

ring to the rear end pinion yoke on a Ford 9” housing.

Part #91195 will mount to most standard Ford 9” rear

housings with a 1.875” diameter pinion yoke. Part #91196

will fit 2.187” diameter, 35 spline yokes. Installation Procedure

•Note: Refer to Figure 1 below for reference on all steps.

1. Install the number of magnets you require for your data

aquisition system into the ring assembly.

2. The magnets are to be seated against the shoulder (towards

the outside diameter of the ring), then glued with an adhesive

such as epoxy, RTV silicone, hot glue, etc. (Note: Some

computers are sensitive to the magnet’s north and south

poles. Install magnets per requirements for your data

aquisition system.)

3. Install the ring halves around the pinion coupler and tighten

the 10-32 x 3/4” cap screws tightly. The beveled edge of the

•Kit Contents:

1 - Two-Piece Aluminum Mounting Ring

2 - 10-32 x 3/4” Cap Screws

4 - Magnets

1 - Sensor Switch Bracket

1 - Sensor Switch

Tighten so that the

gaps are even

Use a washer .060”-.080” thick to prevent

interference with the pinion support radius

Grip Diameter

Be sure the magnets are

seated against the outside

shoulder of the ring

Beveled edge should

face Pinion U-Joint

Set gap at .060”-.100” for

Qwikdata use

Set gap per data aquisition system

per manufacturer’s instructions

Note: Some multi-magnet sensors are pole-sensitive

and must be installed in correct +/- sequence.

FIGURE 1

Fill cavities with

epoxy or silicone

to secure magnets

inside of the ring should face the pinion U-joint. The gap on

each side of the ring should be even to ensure correct timing

on multiple magnet use.

4. Attach the Sensor Switch Bracket to a bolt or stud on the rear

end housing as shown in Figure 1. Attach Sensor Switch and

adjust gap to .060”-.100” for Qwikdata use, or to your data

aquisition system specification.

•Note: Periodically,makesurethemagnetsandmountingring

are secure.

•Caution: Excessive heat can cause the magnets to lose

power.

This manual suits for next models

Table of contents

Other Edelbrock Automobile Part manuals

Edelbrock

Edelbrock 3865 User manual

Edelbrock

Edelbrock 6560 User manual

Edelbrock

Edelbrock Harley Nitrous Systems 63-0052 User manual

Edelbrock

Edelbrock 72279 User manual

Edelbrock

Edelbrock Ford Mustang 17931 User manual

Edelbrock

Edelbrock 5292 User manual

Edelbrock

Edelbrock Axle-Back Exhaust Systems 5773 User manual

Edelbrock

Edelbrock 1478 User manual

Edelbrock

Edelbrock 6009 User manual

Edelbrock

Edelbrock 6606 User manual

Edelbrock

Edelbrock 5291 User manual

Edelbrock

Edelbrock 33505 User manual

Edelbrock

Edelbrock 25-4066 User manual

Edelbrock

Edelbrock 71001 User manual

Edelbrock

Edelbrock Performer-Plus 2132 Instruction manual

Edelbrock

Edelbrock Turbocharger 15012 User manual

Edelbrock

Edelbrock 1727 User manual

Edelbrock

Edelbrock Super Victor Race Manifold 2928 User manual

Edelbrock

Edelbrock Russell 694300 User manual

Edelbrock

Edelbrock 68512 User manual

Edelbrock

Edelbrock 5061 User manual

Edelbrock

Edelbrock 68003 User manual

Edelbrock

Edelbrock 72285 User manual

Edelbrock

Edelbrock 15018 User manual

Popular Automobile Part manuals by other brands

Dakota Digital

Dakota Digital 650277 Installation

bosal

bosal 037031 Fitting instructions

Vintage Air

Vintage Air 571063 manual

GFB

GFB EX38 instruction manual

bosal

bosal 028091 Fitting instructions

Dodge

Dodge 8W-43 Wiring diagram

ICI

ICI Magnum FBM10DGN Installation

Volant Perfomance

Volant Perfomance 19435 installation instructions

BENDIX

BENDIX GEN 4 GEN 5 ABS manual

Vintage Air

Vintage Air 571065 manual

Rugged Ridge

Rugged Ridge 11503.13 installation instructions

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER instructions

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... maintenance

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G operating manual

Toshiba

Toshiba 48-1250 A instruction manual

aldes

aldes EHT2 installation instructions

Go Rhino

Go Rhino 24371T installation instructions

BBK

BBK 18950 installation instructions