Echo PE-2601 User manual
Power Edger
Operator's Manual
MODEL PE-2601
Serial Number 001001 & Up
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual
and a Safety Manual. Both must be read and understood for proper and safe operation.
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
X750000750
10/99
X7502093500
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find
both easy to use and full of helpful operations tips and SAFETY messages.
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual.
Both must be read and understood for proper and safe operation.
THE OPERATOR'SMANUAL —
contains specifications and information for operation, starting,
stopping, maintenance, storage and assembly specific to this product.
THE SAFETY MANUAL —
explains possible hazards involved with the use of Edgers and the
measures you should take to make their use safer.
TABLE OF CONTENTS
Introduction .............................................................. 2
- The Operator's Manual ...................................... 2
- The Safety Manual............................................. 2
Manual Safety Symbols and Important Information. 3
Safety ........................................................................ 3
- General Description ........................................... 3
- Decals ................................................................ 4
- InternationalSymbols ........................................ 4
- Equipment .......................................................... 5
- Fuel .................................................................... 6
- Personal Condition and Safety Equipment ........ 6
- Safe Operation ................................................... 7
- Extended Operation/Extreme Conditions .......... 8
Description ............................................................. 10
- Emission Control ............................................. 10
- Contents ........................................................... 10
Specifications.......................................................... 13
Assembly ................................................................ 14
- Drive Shaft/Power Head .................................. 14
- Throttle Linkage and Ignition Leads................ 14
- Front Handle ................................................... 15
Pre-Operation ......................................................... 15
- Fuel .................................................................. 15
- Equipment ........................................................ 16
- Determine Operation Area .............................. 16
Operation ................................................................ 17
- Starting Cold Engine........................................ 17
- Starting Warm Engine...................................... 18
- Stopping Engine............................................... 18
- Operating Techniques ...................................... 19
Maintenance............................................................ 20
- Skill Levels ...................................................... 20
- MaintenanceIntervals ...................................... 20
- Air filter ........................................................... 21
- Fuel Filter......................................................... 21
- Spark Plug........................................................ 22
- CoolingSystem ................................................ 22
- ExhaustSystem ................................................ 23
- Carburetor Adjustment..................................... 24
- Lubrication....................................................... 25
Troubleshooting...................................................... 26
Storage .................................................................... 27
ServicingInformation ............................................. 28
- Parts ................................................................. 28
- Service ............................................................. 28
- ECHO Consumer Product Support .................. 28
- Warranty Card.................................................. 28
- Additional or Replacement Manuals................ 28
- Manual Ordering Instructions .......................... 28
Specifications, descriptions and illustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and accesso-
ries, and may not include all standard equipment.
CopyRight© 1999 By Echo, Incorporated
All Rights Reserved.
P
OWER
E
DGER
O
PERATOR
'
S
M
ANUAL
3
SAFETY
GENERAL DESCRIPTION
IMPORTANT
See Description and Specification sections for full description and illustration of model variation in power head, and
handle type.
BLADE
GUARD
SAFETY
DECAL
FRONT
HANDLE
POWER
HEAD
THROTTLE
TRIGGER
DRIVESHAFT
HOUSING
DEPTH
WHEEL
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead to
serious personal injury to operator and bystanders.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
NOTE
This enclosed message provides tips for use,
care and maintenance of the unit.
IMPORTANT
NOTE
STOP
SWITCH
EDGER
BLADE
4
Symbol
description/
application
Symbol form/
shape
Symbol
description/
application
Symbol form/
shape
HOT
SURFACE
Carburetor
adjustment
- Idle speed
Carburetor
adjustment
- High speed
mixture
Symbol
description/
application
Symbol form/
shape
Symbol
description/
application
Symbol form/
shape
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection
Emergency stop
Fuel and oil mixture
Finger Severing
Carburetor
adjustment
- Low speed
mixture
Safety/Alert
Avoid all power
lines. This unit is
not insulated
against electrical
current.
Wear hand
protection. Use
two handed.
DO NOT smoke
near fuel.
DO NOT allow
flames or sparks
near fuel.
Wear slip
resistant foot
wear.
Engine choke
control.
Ignition
ON/OFF
Primer
bulb
DECALS
Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING instructions for specific
information.
These decals are in English only:
Shaft Decal
INTERNATIONALSYMBOLS
Keep bystanders away
15 m (50 ft.)
Keep feet away
from blade
Thrown
objects
Direction of
bladerotation
-WARNING-DANGER-
• Whenused improperlythisedgercouldcauseseriouspersonalinjury.Readandfollowallsafetyprecautions
intheowner'smanual. •Neveroperatewithouteye protection. •Alwaysinspectareaforhiddenorthrowable
objects.Neveruseingravel. •Stayclearofrotatingbladeatalltimes.Keepbystandersatleast50'away. •Stop
enginebefore adjusting cuttingheight or performingay service. • Neveroperate with unitpositioned on left
sideofbody. •UseonlyECHOapprovedreplacementbladesonthisunit. • Donotuseedgerbladeonanybrush
cutter. •Edgerattachmentandbladeareintendedforedgingonly. •Afterreplacingorservicingblade,arbors,
nutandcotterpinsmustbe assembled properly.
P
OWER
E
DGER
O
PERATOR
'
S
M
ANUAL
5
EQUIPMENT
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed. Do not use edger if any part is missing or
damaged.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Inspect shield for damage and is securely in place. Replace if shield
is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe
operating condition.
• Check that front handle is adjusted for safe, comfortable operation.
See Assembly for proper adjustment.
WARNING DANGER
• Use only ECHO approved attachments. Serious injury may result
from the use of a non approved attachment combination. Read
and comply with all safety instructions listed in this manual and
safetymanual.
• ECHO, INC. will not be responsible for the failure of cutting
devices, attachments or accessories which have not been tested
and approved by ECHO.
IMPORTANT
Use of the Power Edger on U.S. Forest land and the states of
California, Oregon and Washington requires installation of optional
MufflerBracketKitP/N10099057730.
ATTACHMENTS
AND
ACCESSORIES
6
FUEL
WARNING DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing
or handling or serious personal injury may result.
•Use an approved fuel container.
•DO NOT smoke near fuel.
•DO NOT allow flames or sparks near fuel.
•Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
•NEVER refuel a unit when the engine is HOT!
•NEVER refuel a unit with the engine running.
•DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.
•Securely tighten fuel cap after refueling.
•Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
After Refueling;
•Wipe any spilled fuel from the unit.
•Move at least 3 M (10 ft.) from refueling location before starting.
After use;
•DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating an edger.
Physical Condition --
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection --
Wear eye protection that meets ANSI Z87.1 or CE requirements
whenever you operate the edger.
3 M (10 FT.)
P
OWER
E
DGER
O
PERATOR
'
S
M
ANUAL
7
Hand Protection --
Wear no-slip, heavy duty work gloves to improve your grip on the
edger handles. Gloves also reduce the transmission of machine
vibration to your hands.
Hearing Protection --
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing --
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Hot Humid Weather --
Heavy protective clothing can increase operator fatigue which may lead
to heat stroke. Schedule heavy work for early morning or late afternoon
hours when temperatures are cooler.
SAFE OPERATION
Determine Operation Area
• Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
• Do not operate this product indoors or in inadequately ventilated
areas.
• Review the area to be edged. Look for hazards that could contribute
to unsafe conditions.
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15M (50 ft.) while the
edger is in use.
Use Proper Clothing & Equipment
• Before starting the unit, equip yourself and any other person working
within the 15M (50 ft.) Safety Zone with the required Protective
Equipment and clothing.
8
KeepAFirmGrip
• Hold the front and rear handles with both hands with thumbs and
fingers encircling the handles
Keep A Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
Avoid Hot Surfaces
• During operation, the exhaust area may become very hot, too hot to
touch. Avoid contact during and immediately after operation.
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the edger or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
P
OWER
E
DGER
O
PERATOR
'
S
M
ANUAL
9
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
10
CONTENTS
__ 1, Drive Shaft / Edger Assembly
__ 1,PowerHead
__ 1,PlasticBag(Co-Pack)
__ 1,Operator's Manual
__ 1,Safety Manual
__ 1,Warranty Registration Card
__ 1,ECHO Emissions and Warranty Statement
__ 1,50:1 1 Gal. ECHO Oil Mix
__ 1, Front Handle
__ 4, 5X35 mm screws
__ 4, 5 mm nuts
__ 1,Scrench(CombinationSparkPlugSocket/Screwdriver
__ 1, split pin
__ 1, 4 mm Hexagon Wrench
__ 1,LockingTool
__ Safety Glasses
DESCRIPTION
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and other assembly may be necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
EMISSION CONTROL
The emission control system for this engine is EM (Engine Modification).
AnEmissionControlLabelislocated ontheengine. (This isanEXAMPLE ONLY,informationon labelvariesby engine
FAMILY).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: VEH025UB24RA
DISPLACEMENT: 25.4cc
THIS ENGINE MEETS U.S. EPA PHI AND 1995 -
1999 CALIFORNIA EMISSION REGULATIONS FOR
ULGE ENGINES. REFER TO OWNER’S MANUAL
FOR MAINTENANCE SPECIFICATIONS AND
ADJUSTMENTS.
Table of contents
Other Echo Edger manuals
Echo
Echo PE-2000 Type 1/1E User manual
Echo
Echo DPE-2100 User manual
Echo
Echo BRD-280 User manual
Echo
Echo PE-201 Instruction Manual
Echo
Echo PE-280 User manual
Echo
Echo PE-225 User manual
Echo
Echo PAS-260 PRO - PARTS CATALOG SERIAL NUMBER... Instruction Manual
Echo
Echo PE-225 User manual
Echo
Echo 99944200475 User manual
Echo
Echo PE-266S User manual
