Ebyte E180-ZGI20B-TB User manual

E180-ZG120B-TB User Manual

Chengdu Ebyte Electronic Technology Co., Ltd. E180-ZG120B-TB User Manual

Content

1. Module introduction......................................................................................................................................... 2

2. Instruction......................................................................................................................................................... 2

3. Drive installation.............................................................................................................................................. 4

About us................................................................................................................................................................4

Chengdu Ebyte Electronic Technology Co., Ltd. E180-ZG120B-TB User Manual

1. Module introduction

E180-ZG120B-TB has been pre-welded for testing Chengdu Ebyte E180-ZG120B,please refer to the module

manual for detailed use.

All IO of E180 series wireless modules have been exported.

With CP2102G serial chip, serial communication can be developed.

With USB interface, can be directly plugged into the computer for use.

Users can access external power supply and serial port by themselves.

Stable work and easy to develop.

2. Instruction

Chengdu Ebyte Electronic Technology Co., Ltd. E180-ZG120B-TB User Manual

Description：

No.

Description

AVDD

Module power port, 3.3V power

supply is recommended

3.3V

Baseboard LDO output 3.3V, can

supply power to the module

TXD

TXD of cp2102

RXD

RXD of cp2102

PA1

RXD of the module

PA0

TXD of the module

No.

Name

Direction

Function

GND

Ground, connected to power supply reference ground

GND

Ground, connected to power supply reference ground

PD13

Input

TOUCHLINK pin, which is continuously pulled lower than 3000ms,

will initiate a ZLL network establishment or join request

PD14

Input

WAKE pin is mainly used to wake up the sleep terminal. It is high level

when powered on. When the pin is pulled low externally, the sleep

terminal device will be woken

PA0(TX)

Output

Serial port transmission port TX

PA1(RX)

Input

Serial port receiving port RX

PA2

Input/Outp

Reserve

PA4

Input/Outp

Reserve

PB11

Input

Operating mode switching pin. When the pull-low time is longer than

500ms, the operating mode is switched.

PB12

Input

UART_BAUD_RESET pin is used to reset the device baud rate. The

power-on default is high level. In any mode, if this pin is pulled lower

for more than 1000ms, the serial port parameters of the module will be

restored to the default 115200.

PB13

Output

ACK pin is used to indicate the last user data transmission status. This

pin is pulled low before the transmission is started, and the pin is pulled

high after the transmission.

PB14(GPIO0)

Input/Outp

GPIO Input/ Output port 0

3.3V

Module power supply positive reference voltage, voltage range

GND

Ground, connected to power supply reference ground

Chengdu Ebyte Electronic Technology Co., Ltd. E180-ZG120B-TB User Manual

PB15(GPIO1)

Input/Outp

GPIO Input/ Output port 1

PA5

Input/Outp

Reserve

PA3

Input/Outp

Reserve

PD15

Output

AUX pin indicates the current working status of the device. When the

pin is low level, it indicates that the device is busy, and high level

indicates that the device is idle.

PC6(GPIO2)

Input/Outp

GPIO Input/ Output port 2

PC7(GPIO3)

Input/Outp

GPIO Input/ Output port 3

PC8(ADC1)

Input

ADC detection port 1

PC9(ADC2)

Input

ADC detection port 2

PC10(ADC3)

Input

ADC detection port 3

PC11(ADC4)

Input

ADC detection port 4

SWCLK

Input/Outp

DBG_SWCLKTCK

SWDIO

Input/Outp

DBG_SWDIOTMS

PF2(PWM0)

Output

PWM output port 0

PF4(PWM2)

Output

PWM output port 2

PF5(PWM3)

Output

PWM output port 3

PF7

Output

The LINK pin indicates the current network status of the module, output

high level meter has been added to the network.

PF6(PWM4)

Output

PWM output port 4

PF3(PWM1)

Output

PWM output port 1

PD12

Input/Outp

Reserve

PD11

Input/Outp

Reserve

PD10

Input/Outp

Reserve

GND

Input/Outp

Ground, connected to power supply reference ground

nRESET

Input

Reset pin

3. Drive installation

The CP2102 chip is used as the serial port. Please download and use the driver software provided by our company.

After installation, the serial port can be identified in the device manager.

About us

Sales hotline: 4000-330-990 Tel: 028-61399028

Support: support@cdebyte.com Website: www.ebyte.com

Address: Innovation Center B333~D347, 4# XI-XIN road, High-tech district (west), Chengdu, Sichuan,

China

Table of contents

Other Ebyte Control Unit manuals

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual