Eaton Powerware 5125 User manual
Powerware 5125 (9910-E33) UPS
Installation Guide for IBM Applications
®
®
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
IBM, pSeries, AIX, xSeries, AS/400, and RS/6000 are registered trademarks and iSeries, OpenPower, and i5/OS are
trademarks of International Business Machines Corp.
Eaton, Powerware, X-Slot, and LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton
Corporation or its subsidiaries and affiliates.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Linux is a registered trademark of Linus Torvalds.
Burndy is a registered trademark of Framatone Connectors International.
ECopyright 2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1 i
Table of Contents
1 Installation 1.........................................................
Parts List 1..........................................................................
UPS Internal Battery Connection 3..........................................................
Setup and Installation 4.................................................................
Tools Required 4....................................................................
Rack-Mount Setup 5.................................................................
EBM Installation 10.....................................................................
UPS Installation 11.....................................................................
Remote Emergency Power-off Installation 12...................................................
Power Connections and Startup 14..........................................................
Load Segments 20......................................................................
2 Operation 21..........................................................
Turning the UPS On 21...................................................................
Starting the UPS on Battery 21.............................................................
Turning the UPS Off 21...................................................................
Operating Modes 22....................................................................
Normal Mode 22....................................................................
Battery Mode 23....................................................................
Bypass Mode 23.....................................................................
Standby Mode 23....................................................................
Configuration Mode 24...................................................................
3 Communication 27.....................................................
Single-Port Card 27.....................................................................
Communication Options 30................................................................
i5, iSeries, or AS/400 and Serial Server Interface Overview 30....................................
Serial (TTY) Interface Overview 33........................................................
p5 or pSeries with Logical Partitions Interface Overview 34......................................
4 Service and Support 35.................................................
TABLE OF CONTENTS
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1
ii
This page intentionally left blank.
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1 1
Chapter 1 Installation
Parts List
IBM part numbers are subject to change without notice.
Table 1. E33 Base Configuration (42R8065)
Quantity IBM MN IBM FC IBM PN Eaton®PN Description
1E33 —42R8065 05147155-3995 E33 UPS 3000 VA, 2700W (in shipping carton or
factory-installed in rack)*
103006256 Accessory Kit:
S(1) UPS Front Cover (157603827-003)*
S(1) Read Me First Card (164201568)
S(2) Square-Hole Adapter Plates (157606109-001)*
S(1) Left Rail Assembly (103006173)*
S(1) Right Rail Assembly (103006172)*
1 — — 42R8066 05147532-3992 E33 Accessory Kit
* If the UPS is factory-installed in an IBM rack, these items are pre-assembled.
Table 2. E33 Application Matrix
IBM MN IBM FC IBM PN Eaton PN Description
Quantity for
p5/pSeries®
Rack Worldwide
Quantity for
i5/iSeriest
Rack Worldwide
—2934139J4824 116750221-001 -X Web/SNMP
Card2Kit
ConnectUPStMin: 0, Max: 1 —
—2939142R4332 103004741-5591 Relay-Serial Card and Cable
Kit (DB-9, 1.8m/6 ft; DB-25,
9.1m/30 ft)
—Min: 0, Max: 1
—6643 42R8067 05147156-3996 Extended Battery Module
(EBM)
Min: 0, Max: 4
— — 42R8068 05147533-3992 EBM Accessory Kit 1 per FC 6643
Varies Varies Varies Varies UPS Input Power Cord 1 per E33 UPS
1Maximum: One FC 2934 or 2939 per E33 UPS.
2ConnectUPS-X Web/SNMP Card required if implementing Logical Partitions (LPARs) on p5 or pSeries.
INSTALLATION
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1
2
Table 3. E33 Accessory Kit (42R8066)
Quantity Eaton PN Description
1164201383 Powerware 5125 Two-in-One UPS (2400/3000 VA) User’s Guide
1164201695 Powerware 5125 (9910-E33) Installation Guide for IBM Applications
1164201568 Read Me First Card
4152601942-001 IEC 320-C13 to C14, 10A Equipment Power Cords (2m/6.6 ft)
1152601971-001 IEC 320-C19 to C20, 16A Equipment Power Cord (4.5m/14.8 ft)
1154105635-001 Connector Plug, 10A, 2-Pin
1103005159 Burndy®to IEC 320-C20 16A Power Cord (1.8m/6 ft)
1Bag 130500051-001 Cord Retention Clips
1103004870 Software Suite CD
1124102043-001 UPS to Server Communication Cable (DB-9 to DB-9, 1.8m/6 ft)
2130500110-001 Mounting Handles
4180500200-002 Mounting Handle Screws
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
Table 4. E33 6643 EBM Configuration (42R8067)
Quantity IBM MN IBM FC IBM PN Eaton PN Description
1 — 6643 42R8067 05147156-3996 E33 6643 EBM 2U High (in shipping carton or
factory-installed in rack)*
103006302 Accessory Kit:
S(1) EBM Front Cover (157603827-103)*
S(2) Square-Hole Adapter Plates (157606109-001)*
S(1) Left Rail Assembly (103006173)*
S(1) Right Rail Assembly (103006172)*
S(2) Mounting Handles (130500110-001)*
S(4) Mounting Handle Screws (180500200-002)*
1 — — 42R8068 05147533-3992 EBM Accessory Kit
* If the EBM is factory-installed in an IBM rack, these items are pre-assembled.
INSTALLATION
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1 3
Table 5. EBM Accessory Kit (42R8068)
Quantity Eaton PN Description
1164201378 Powerware 5125 Two-in-One EBM (2500/3000 VA) User’s Guide
1152602008 EBM Cable
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
UPS Internal Battery Connection
NOTE Check the battery recharge date on the shipping carton label. If the date has expired
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
To ensure proper battery operation before installing the UPS:
1. Verify that the UPS is off and unplugged.
2. Remove the packing material (see Figure 1).
Figure 1. Removing Packing Material
3. Connect the internal battery connector (see Figure 2).
NOTE A small amount of arcing may occur when connecting the batteries. This is normal
and does not damage the unit or present any safety concern.
INSTALLATION
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1
4
Figure 2. Connecting the Internal Battery Connector
4. Install the UPS front cover (see Figure 3).
Figure 3. Installing the Front Cover
Setup and Installation
The E33 UPS can be purchased separately or factory-installed in an IBM
iSeries or pSeries rack.
NOTE If the UPS is pre-installed in an IBM pSeries (RS/6000®) system, continue to “EBM
Installation” on page 10 or “UPS Installation” on page 11.
Tools Required
To assemble the components, the following tools may be needed:
SMedium flat-bladed screwdriver
S#2 Phillips screwdriver
S8mmwrenchorsocket
INSTALLATION
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1 5
Rack-Mount Setup
The rail kit can be installed in 48-cm (19-inch) racks and needs only 2U of
valuable rack space.
NOTE Mounting rails are required for each individual cabinet and are located in the UPS
and EBM cartons. All hardware is supplied.
NOTE The UPS and any optional cabinets MUST be installed at the bottom of the rack. If
placed in a rack with existing equipment, the rack must be reconfigured to allow the UPS
installation at the bottom of the rack.
Each rail kit requires one (1) of each item in the following list:
SLeft rail assembly (located in the UPS and EBM cartons)
SRight rail assembly (located in the UPS and EBM cartons)
SMounting handles and screws (located in the UPS and EBM cartons)
SRail hardware kit (located in the E33 UPS and EBM accessory kits)
To install the rail kit(s):
1. Loosen the assembly wing nuts on both rail assemblies and adjust
the rail size for the depth of your rack (see Figure 4).
Assembly Wing Nuts
Front
Rear
Rear Hold-Down Bracket
Figure 4. Adjusting the Rail Depth
INSTALLATION
EATON Powerware®5125 (9910-E33) UPS Installation Guide for IBM®Applications S164201695 Rev 1
6
2. Select the proper holes in the rail for positioning the UPS and any
optional cabinets in the rack.
3. Secure the rail to the front of the rack with two pan-head screws
and one adapter plate. Insert the screws through positions 3 and 4
oftherail(seeFigure5).
NOTE Do not tighten the screws until the UPS or EBM is installed.
Assembly Wing Nuts
Front Rail Pan-Head
Screws
Adapter
Plate
Position 4
Position 3
Figure 5. Securing the Front of the Rail
4. Using two clip nuts and two hex-head screws, attach the rail to the
rear of the rack (see Figure 6 and Figure 7).
The bottom rail uses positions 2 and 4 for the rear hex-head
screws. If you are installing additional rails, place the next rail
4 holes above the last installed screw.
Other manuals for Powerware 5125
9
This manual suits for next models
1
Table of contents
Other Eaton UPS manuals
Eaton
Eaton Eaton 5PX Assembly instructions
Eaton
Eaton Power Xpert 9395 User manual
Eaton
Eaton Powerware 9390 User manual
Eaton
Eaton 9PX5KP1 Installation and operating instructions
Eaton
Eaton Power Xpert 9395 User manual
Eaton
Eaton Powerware 9125 User manual
Eaton
Eaton DIN24240DC User manual
Eaton
Eaton Powerware 9130 User manual
Eaton
Eaton Powerware 5110 User manual
Eaton
Eaton UPS 20 User manual
Eaton
Eaton Powerware 9155 User manual
Eaton
Eaton Powerware Series User manual
Eaton
Eaton 9125 Two-in-One UPS 2500 User manual
Eaton
Eaton 93E 30IAC-D User manual
Eaton
Eaton DX 10000LXL User manual
Eaton
Eaton Ellipse ASR 450 User manual
Eaton
Eaton Powerware 9125 User manual
Eaton
Eaton EX RT 7 User manual
Eaton
Eaton Power Xpert 9395 High Performance User manual
Eaton
Eaton Powerware 9355 Parallel User manual
