Earth Way 2130 User manual

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

THIS SPREADER COMES PARTIALLY ASSEMBLED, REQUIRING YOU TO INSTALL THE WHEELS, HANDLE ASSEMBLY AND

CONTROL ROD. IT SHOULD TAKE APPROXIMATELY 10 MINUTES WITH THE USE OF TWO 7/16” WRENCHES AND 1 PAIR

OF PLIERS.

;Clean the impeller plate after each use. Material stuck on the impeller blades will cause uneven spreading.

;Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spread patterns. Wet material will also change the spread pattern and ow rate.

;Clean your spreader thoroughly after each use. Wash between the shut off plate and bottom of the hopper.

;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

;When using Rock Salt remove salt from the hopper daily. Rock Salt will reconstitute back into a solid block over night

with humidity. As a preventative measure, spray all metal parts thoroughly (inside the tubing too) with WD-40 to prevent

corrosion.

1. Open carton and remove the handle assembly, wheels, and

spreader from carton.

2. Turn spreader upside-down on to the hopper.

Pt# 53107 PAGE 1

2130 HIGH-OUTPUT Broadcast spreader

ASSEMBLY and OPERATING INSTRUCTIONS Rev. 3-10

EarthWay



Gearbox

Axle Assembly

Lower

Handle

Frame

Brace

Cross Brace

Axle Bushing

3. Ensure that the axle bearings are pushed into the axle bushing

on both sides as shown. Install drive wheel (both wheels are

interchangeable) to axle using pin hole nearest to lower handles as

shown. Insert 2” cotter pin through wheel and through axle. Bend

with pliers to prevent pin from falling out.

4. Install coast wheel to axle, then using outside pin hole as shown, insert 1” cotter pin

through axle (not thru the wheel). Bend with pliers to prevent pin from falling out.

2” Cotter Pin

1” Cotter Pin

Coast Wheel

Drive Wheel

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS

REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com SKYPE: EARTHWAY.TECH

1/4 - 20 Lock-nut

1/4 - 20 x 2” Bolt

Pivot Bracket

5. Install handle shaft to lower handles and pivot & bracket assembly as

shown. Using 2” bolts and locknuts.

TIGHTEN BOLTS AND NUTS NOW.

PAGE 2

1/4-20 x 2”

Hex Head

Bolt

Gauge &

Lever Assembly

Handle

Spacer

Upper Handles

1/4-20

Locknuts

POSITIONS

LOWER

MIDDLE

UPPER

Handle Shaft

Long end

6. (This step is only required if you want to change the position of the

handles) NOTE: BEFORE INSTALLING GAUGE AND UPPER

HANDLES TO HANDLE SHAFT, UPPER HANDLES FEATURE

THREE POSITIONS FOR OPERATOR’S COMFORT.

If operator chooses middle or upper positions, use handle spacer in hole

nearest to handle grips.

Insert 2” bolt through upper handle, then through handle spacer through

other upper handle and secure with locknut.

DO NOT TIGHTEN LOCKNUT YET. TIGHTEN THIS NUT LAST.

Now slide the upper handle assembly over the handle shaft (on the

end with the bolt holes closer to the end).

Install gauge & lever using (2) 2” bolts. Be sure gauge is on left hand

side. Tighten locknuts to gauge rst.

TIGHTEN ALL HARDWARE NOW.

Gauge & Lever

Control Rod

Tabbed Hole

Control Rod

Lever Tension Nut

1/4-20

Hex Nuts

Pivot

Bracket Control

Rod

7. Install Control Rod by installing attened end of Control Rod into Lever on Gauge

as shown. Turn to lock in place. {Make sure that there is a plain 1/4-20 Hex Nut

threaded about halfway up the threads}

Push lever forward to full OPEN setting. Align and push the Control Rod through

the angle attached to the Pivot Bracket. Now install 1/4-20 regular nut on to

control rod. {One nut on either side of the angled plate}

Next pull pivot & bracket back so that the shut off plate in the hopper is in the full

open position and adjust the Hex Nuts on the Pivot Bracket angle to secure the

angled bracket. Now tighten the nuts against the pivot angled bracket to prevent

change in calibration.

5-YEAR LIMITED WARRANTY

EarthWay

Products, Inc. warrants this product free of defects in original workmanship and materials for

a period of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance

is found,

EarthWay

Products, Inc. at its discretion will repair or replace the part(s) or product at no charge

provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear

and tear as determined by

EarthWay

at its discretion may require that the part(s) or product

be returned along with the original purchase receipt at owners’ expense for examination and compliance with

the terms of this warranty. (Do not return any product without rst receiving authorization from

EarthWay

Products, Inc.). To seek remedy under this warranty, contact

EarthWay

Products, Inc. at 574-848-7491,

techsupport@earthway.com or write to (

EarthWay

Products, Inc. P.O. Box 547 Bristol, Indiana 46507) and

describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the

part(s) or product; any labor charges associated with repair or replacement of non-conformances are specically

excluded. Due to the corrosive nature of most fertilizers and ice melt products,

EarthWay

Products, Inc. makes

no warranty against and specically excludes part(s) or product degradation or failure due to corrosion or its

effects. Clean and dry your spreader thoroughly after each use, as a preventative measure, coat all metal parts

with a light oil or silicon spray.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct from the

manufacturer. Be sure to give the following information when

ordering.

 Model Number

 Part Number

 Part Description

Call (574) 848-7491 or 800-294-0671 to place an order with a

credit card.

OPERATING INSTRUCTIONS

Before lling hopper, become familiar with the operation of

this spreader.

;Move stop bolt on gauge assembly to the proper position

for the material being applied.

;While pushing spreader forward, push control lever

forward to stop bolt.

;To stop, pull lever backward to close ow hole before you

stop moving.

;When nished, empty any remaining material from

hopper.

;Thoroughly wash and dry your spreader before storing.

PAGE 3

DO NOT RETURN TO DEALER FOR REPAIR

EARTHWAY PRODUCTS, INC.

1009 Maple Street

P.O. Box 547

Bristol, IN 46507

FOR YOUR RECORDS

Date Purchased

Store Name

2130 HIGH-OUTPUT Broadcast Spreader ~ Parts List

KEY # PART # DESCRIPTION KEY # PART # DESCRIPTION

1 60250 HOPPER ASSEMBLY 18 12354 ICE MELT SHUT-OFF

2 33117 AGITATOR 19 25222 LOWER HANDLE

3 31141 #14 X 3/4" TYPE "AB" HWHS ZINC 20 25722 FRAME

4 12259 HOPPER BUSHING 21 44292 FRAME BRACE

5 31122 #8 X 5/8" PHPS TYPE A BLACK 22 25228 CROSS BRACE

6 32100 1/4-20 HEX NUT ZINC 23 12109 IMPELLER (9" DIA)

7 19132 7/8" TUBE PLUG 24 36105 1/8" X 1 1/4" COTTER PIN SS

8 60300 PIVOT & BRACKET ASSEMBLY 25 12274 GRIP 7.5" LONG

9 32103 1/4-20 NYLON INS LOCKNUT ZINC 26 60334 GEAR BOX & AXLE ASSEMBLY

10 42259 LOWER CONTROL ROD 27 12148 AXLE BEARING

11 60499 GAUGE & LEVER 28 12152 AXLE BUSHING

12 60175 UPPER HANDLE SQ W/GRIP 29 33109 3/16" X 2" COTTER PIN ZINC

13 12344 HANDLE SPACER 30 70138 PNEUMATIC DRIVE/COAST WHEEL

14 31121 1/4-20 X 1 1/4" HHCS ZINC 31 33108 3/16" X 1" COTTER PIN ZINC

15 25223 HANDLE SHAFT 32 31114 1/4-20 X 1 3/4" HHCS ZINC

16 42256 CONTROL ROD OPTIONAL 60184 SALT DEFLECTOR KIT

17 31120 1/4-20 X 2" HHCS ZINC OPTIONAL 77003 HEAVY DUTY RAIN COVER 13" X 18"

vvvvvvvv

27 28

77003

OPTIONAL

Heavy-Duty

Rain Cover

60184

OPTIONAL

Salt Deflector Kit

EarthWay

Products, Inc.

P.O. Box 547

Bristol, IN 46507

Phone: 800-294-0671

www.earthway.com

Other Earth Way Spreader manuals

Earth Way

Earth Way Polar Tech 90399 User manual

Earth Way

Earth Way Prizelawn BF l User manual

Earth Way

Earth Way 2100P Estate User manual

Earth Way

Earth Way 2130 High-Output User manual

Earth Way

Earth Way 2170-XL User manual

Earth Way

Earth Way Polar Tech 2040PI-PLUS User manual

Earth Way

Earth Way POLAR TECH 90365 User manual

Earth Way

Earth Way Ev-N-Spred 2050 User manual

Earth Way

Earth Way 2050 User manual

Earth Way

Earth Way 7350SU User manual

Earth Way

Earth Way Ev-N-Spred M24SSD Series User manual

Earth Way

Earth Way EV-N-SPRED GT 3100 User manual

Earth Way

Earth Way M80ECM User manual

Earth Way

Earth Way 2600A-Plus Estate User manual

Earth Way

Earth Way 2170 User manual

Earth Way

Earth Way M40 User manual

Earth Way

Earth Way EV-N-SPRED C22HD User manual

Earth Way

Earth Way 2600A-PLUS User manual

Earth Way

Earth Way EV-N-SPRED C24HD User manual

Earth Way

Earth Way POLAR TECH 90365 Installation instructions

Earth Way

Earth Way 2040Pi-Plus User manual

Earth Way

Earth Way EV-N-SPRED M20 User manual

Earth Way

Earth Way EV-N-SPRED M30 User manual

Earth Way

Earth Way EV-N-SPRED C22HD User manual

Popular Spreader manuals by other brands

PEQUEA

PEQUEA GT-100 Operator's manual

Herculano

Herculano H2RS9 instruction manual

Epoke

Epoke SKE8 instruction manual

GEA

GEA EL44 Instruction manual and installation instructions

Boss Snowplow

Boss Snowplow TGS 800 owner's manual

Fisher

Fisher EMERSON 168 Series installation guide

Fisher

Fisher POLY-CASTER 78601 owner's manual

TurfEx

TurfEx RS7200 Owner's/operator's manual

Ferris

Ferris Pathfinder Series Operator's manual

Fayat Group

Fayat Group DYNAPAC S100 operation & maintenance

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Operator's manual & parts list

EASTMAN

EASTMAN CR 500 instruction manual

Nogueira

Nogueira RoyalFlow-600 instruction manual

Buyers

Buyers TGS05B installation instructions

Magnum

Magnum V-BOX PV Series Installation and operating instruction manual

Meyer's

Meyer's VB280 INSTRUCTION AND PARTS BOOK

SnowEx

SnowEx VX-4210 owner's manual

Kramer

Kramer VM-400HDCP user manual