Dymo LabelWriter DUO User manual

Declaration of

Conformity

DYMO Corporation

44 Commerce Road

Stamford, CT 06902-4561

Phone: (203) 355-9000

Fax: (203) 355-9090

Equipment Information

Description: Direct Thermal Printer

Models: LabelWriter 300 (90791), 330 (90792),

330 Turbo (90793), EL40 (90644), EL60

(90645), Turbo (90737)

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC (Federal

Communications Committee) rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses, and

can radiate radio frequency energy, and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try correcting the

interference by one or more of the following

measures:

Reorient the receiving antenna.

Increase the separation between the equipment

and the receiver.

Connect the equipment to an outlet on a circuit

different from that to which the receiver is con-

nected.

Use shielded cables to connect this device to

computers.

Consult the dealer or an experienced radio/TV

technician for help.

You may ﬁnd helpful the following booklet, prepared by

the FCC: Interference Handbook. This booklet is available

from the U.S. Government Printing Ofﬁce, Superintendant

of Documents, Washington, DC 20402-9325.

WARNING: Changes or modifications to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate the

equipment and void the manufacturer’s warranty.

Certification

This device has been tested and complies with the

requirements of:

The EMC Directive

EN55022: Radiated and Conducted Emissions B

EN50082-1: Generic Immunity ESD, RF, and Transient

Susceptibility and Low Voltage Directive Product Safety

EN60950

reserved. Printing 3/01

Trademarks

LabelWriter is a registered trademark of DYMO

Corporation. DYMO is a registered trademark of Esselte

Corporation. All other trademarks are properties of their

respective holders.

iii

Contents

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Your New LabelWriter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1

Getting Started

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DYMO Label Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Creating Your Own Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2

Using the Label Designer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Object Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Starting the Designer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Creating a New Label File . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Opening an Existing Label File. . . . . . . . . . . . . . . . . . . . . . . 15

Adding an Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Moving and Resizing Objects . . . . . . . . . . . . . . . . . . . . . . . . 16

Saving Your Label to a File . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chapter 3

Using the List Manager

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 4

Setting Preferences

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Functional Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Folders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Chapter 5

Printing With Other Applications

. . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Add-In for Microsoft Word. . . . . . . . . . . . . . . . . . . . . . . . . . 29

Printing With Other Applications . . . . . . . . . . . . . . . . . . . . . 32

Chapter 6

Maintenance and Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . 39

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Appendix A

Networking the LabelWriter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Connecting to a LabelWriter Over a Network . . . . . . . . . . . 43

Other Networking Solutions. . . . . . . . . . . . . . . . . . . . . . . . . 43

Appendix B

Labels & Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Appendix C

Technical Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

LabelWriter Developer Information. . . . . . . . . . . . . . . . . . . 48

Introduction

Your New

LabelWriter

Congratulations on purchasing the DYMO

LabelWriter. After a short time, you will realize

how many of your daily tasks will be simpliﬁed

by using the DYMO LabelWriter.

Your LabelWriter will help you label ﬁle folders,

diskettes, video cassettes, mail packages, name

tags, and print Internet postage. With a little

imagination, you will think of hundreds of ways

to use the LabelWriter to make your job easier

and more efﬁcient.

Features

Software

The DYMO Label Software includes many

features that make it ﬂexible and easy to use.You

can set your default return address so that you do

not have to enter your address every time you

print a label.You can import graphics to use with

your labels, and select a default logo ﬁle so you

don’t need to import your logo each time you

create a new label. Of course, you can easily

override these default values at any time.

DYMO is even integrated into Microsoft

Word

so that you can easily print labels directly from

the Word toolbar.

Hardware

Your LabelWriter printer does not use toner, ink

cartridges, or a ribbon to print. The LabelWriter

uses advanced

thermal

printing technology to

print on specially treated labels.

Introduction

Thermal printing is based on the principle of heat

transfer from the thermal print head inside the

LabelWriter printer to the label. A row of

miniature heating elements on the print head is

pressed against the thermal labels. As a speciﬁc

element generates heat, a thermal reaction takes

place at that point on the label and the label

becomes discolored.

Labels

The only supplies you will ever need for this

printer are the labels. We recommend you only

use DYMO brand labels.

How long your labels will last depends on how

the labels are used. Thermal labels are susceptible

to fading in two ways:

Exposure to direct sunlight or ﬂuorescent light

for an extended period of time will cause fading.

Contact with plasticizers (for example labels

placed on plastic ring binders) will cause fading.

In the original packaging, the label shelf life is 18

months. When used for short-term applications

(envelopes, packages, etc.), fading has never

been reported as a problem. When used to label

ﬁles in a ﬁle cabinet, fading is very gradual over

many years. When applied to the edge of a

notebook that is then placed on a shelf in the sun,

fading begins within a few months.

When not in use, keep the labels stored in a cool

dry place and in the black bag in which they were

shipped to prolong label life.

Getting Help

Before making labels you should be aware of the

various help resources available to you. DYMO

Label Software comes with extensive Help.At

times in this manual, you will be directed to the

Help for more detailed discussion or instructions

on various topics.

To access the Help:

Click

LabelWriter Help

on the

Help

menu.

The Help is opened in your Web browser.

Chapter 1

Getting Started

DYMO Label Software is a general-purpose label printing

program that is speciﬁcally designed to help you get the

most out of your LabelWriter printer. The program

includes:

Many ready-to-use templates for common labels.

A built-in Designer you can use to create your own

templates.

A built-in List Manager that lets you save addresses or

other types of lists.

An add-in to print directly from Microsoft Word.

DYMO Label

Window

The following ﬁgure introduces the features available from

the DYMO Label Software main window

The ﬁrst time you open DYMO Label Software, you are

prompted to enter your return address and select a default

logo. See "User Information" on page 23 for instructions

on how to deﬁne your return address and select a default

logo ﬁle.

SaveOpen Print Paste

Open List

Manager

Open

Designer

Template

List

Label

Workspace

Rulers

Chapter 1: Getting Started

Creating

Your Own

Label

This tutorial guides you through the steps necessary to

create, print, and save a customized label. The best way to

start is to learn how to modify one of the label templates

included with the software. In this tutorial, you will

customize a shipping label.

You can only print this shipping label on wide print-head

printers. Although the LabelWriter EL40 and

LabelWriter 300 cannot print this shipping label, we

recommend that you follow along. This tutorial will give

you valuable information on how to access the various

text and design objects and change their attributes.

Choose a

Template

The ﬁrst step is to choose a label template as the basis for

your new label.

Click

DYMO Label Software

from the

Apple

menu to

start the program.

The

DYMO Label

window is displayed containing a

blank label.

In the

Label Templates

box, click the

Shipping with

graphic (30256)

template.

The 30256 label is shipped with the EL60, Turbo, 330,

and 330 Turbo model printers. If you have an EL40 or

300 model printer, select this label anyway, and follow

along with the exercise.

Creating Your Own Label

Notice that all templates are listed with the label type ﬁrst,

then any important objects on the template, and ﬁnally the

part number of the label.

The

Shipping with graphic (30256)

template is

displayed.

Changing the

Graphic

The next step in this tutorial is to customize the graphic.

As you will see, to modify an object’s attributes, you

simply

click the object. A dialog box appears that you can

use to change the object’s attributes.

To change the logo:

Click the telephone graphic that appears on the label.

The

Graphic Settings

dialog box appears.

Click the

File

option under

Select Image Source

The

Insert Image

button changes to read

Select File

3. Click Select File.

The Open dialog box is displayed listing the contents of

the default clipart directory which contains the Business,

Miscellaneous, and Sign folders.

4. Select the Miscellaneous folder and click Open.

Chapter 1: Getting Started

The contents of the Miscellaneous folder are displayed.

5. Select the Comput1.jpg ﬁle.

A preview showing the contents of the Comput1.jpg

graphic ﬁle is displayed.

6. Click the Open button.

The Comput1.jpg graphic is displayed in the Graphic

Settings dialog box.

7. Click OK.

The computer graphic is displayed on the label replacing

the telephone graphic.

Changing the

Return

Address

Next, you’ll change the return address.

To enter the return address:

1. Click the text in the label’s upper-right corner.

The Text Settings dialog box is displayed.

Other manuals for LabelWriter DUO

This manual suits for next models

Table of contents

Other Dymo Label Maker manuals

Dymo

Dymo LetraTag User manual

Dymo

Dymo LabelManager 280 User manual

Dymo

Dymo LabelWriter 4XL Label Printer User manual

Dymo

Dymo LetraTag User manual

Dymo

Dymo LabelWriter 550 User manual

Dymo

Dymo LabelManager 350 User manual

Dymo

Dymo LetraTag Plus LT-100T User manual

Dymo

Dymo LabelWriter 400 Duo Guide User manual

Dymo

Dymo LabelWriter Twin Turbo User manual

Dymo

Dymo LabelMANAGER 150 Quick start guide

Dymo

Dymo LabelManager 360D User manual

Dymo

Dymo LabelWriter SE450 Label Printer Use and care manual

Dymo

Dymo LabelManager 210D User manual

Dymo

Dymo XTL 300 User manual

Dymo

Dymo LabelWriter DUO User manual

Dymo

Dymo LabelWriter 450 Duo Label Printer Product manual

Dymo

Dymo LabelWriter 160E User manual

Dymo

Dymo Cool Clicks Labelmaker A2195a-US User manual

Dymo

Dymo LabelWriter 310 Owner's manual

Dymo

Dymo LabelManager Series Installation guide

Dymo

Dymo LETRATAG 100T User manual

Dymo

Dymo ExecuLabel LM450 User manual

Dymo

Dymo LabelManager 120P User manual

Dymo

Dymo LabelManager Wireless PnP User manual

Popular Label Maker manuals by other brands

Brother

Brother P-Touch 2420PC Quick reference guide

newell

newell Dymo LabelManager 210D user guide

Brother

Brother TD-4000 Gu

U-Line

U-Line BROTHER H-8754 manual

Tharo Systems

Tharo Systems H-435+ user manual

Brother

Brother E300 user guide

Godex

Godex RT700 SERIES Service manual

ID Technology

ID Technology 252 Operator / technical manual

Labelmate

Labelmate MC-11 user manual

CAB

CAB XD4M/300 Service manual

Avery Dennison

Avery Dennison Pathfinder 6057 System administrator guide

Brother

Brother P-touch PT-9700PC user guide

TSC

TSC PEX1000 Series user manual

Adkins

Adkins Label Master user guide

Epson

Epson LabelWorks LW-400 Specifications

Primera

Primera 510212 user manual

Brady

Brady BradyPrinter S3100 quick start guide

DuraLabel

DuraLabel LabPRO user guide