Durabrand HPS-2909 User manual
Service Manual
Model HPS-2909
CODE: 1.01.72342.51
HPS-2909
1
INDEX
1. GENERAL.....................................................................................................................2
1.1 PRODUCT FRONT VIEW...........................................................................................2
1.2 PRODUCT BACK VIEW.............................................................................................3
1.3 REMOTE CONTROL...................................................................................................4
2. TECHINICAL SPECIFICATION.................................................................................5
2.1 AUDIO............................................................................................................................5
2.2 POWER SUPPLY........................................................................................................8
2.3 FRAME GEOMETRIC...............................................................................................11
2.4 PURITY........................................................................................................................18
2.5 CONVERGENCE.......................................................................................................18
2.6 VIDEO..........................................................................................................................19
3. CALIBRATION GUIDE.............................................................................................22
3.1 IMPORTANT RECOMENDATIONS.......................................................................23
3.2 DEFINITION OF THE REGISTERS........................................................................24
3.3 GEOMETRY OF THE IMAGE..................................................................................27
3.4 WHITE BALANCE.....................................................................................................27
3.5 SCREEN ADJUSTMENT.........................................................................................28
3.6 AGC ADJUSTMENT.................................................................................................28
4. MATERIAL LIST........................................................................................................29
5. ELECTRICAL SCHEME...........................................................................................44
5.1 MAIN AND REMOTE CONTROL PCB..................................................................45
6. SILKTOPS AND SOLDERS....................................................................................46
6.1 MAIN PCB....................................................................................................................46
6.2 REMOTE CONTROL PCB........................................................................................48
7. EXPLODED VIEW......................................................................................................50
8. BLOCK DIAGRAM......................................................................................................51
HPS-2909
2
1. GENERAL
1.1 Product Front View
1.1.1 Front Panel Functions and Indications
1Master 8Channel +
2Standby 9Menu
3Remote control sensor 10 AV
4Power 11 Video IN 1
5Volume - 12 Audio IN 1 L (mono)
6Volume + 13 Audio IN 1 R
7Channel -
HPS-2909
3
1.2 Product Back View
a) Back Panel Functions and Indications
1Subwoofer OUT 5AV-2 IN audio R
2AV-2 IN video 6Audio OUT R
3AV-2 IN audio L/Mono 7Audio OUT L
4S-Video IN AV-2 8AERIAL Cable
b) Functions
Image Sound
Menu Functions Functions Install
VHF channel from 2 to13
UHF channel from 14 to 69Channel Cable TV channel from 1 to 125
c) Characteristics
Product Dimensions 672X610X515 mm
Weight 34,0 kg
d) Supply
Unit Nominal Min. Max.
Supply Voltage ( FREE VOLTAGE ) 120 - -
Vac 240 - -
Supply Frequency Hz 50/60 - -
Stand by W- - 3
Consumed Power In Operation W- - 125
HPS-2909
4
1.3 REMOTE CONTROL
1.3.1 Remote Control Functions
1Power 9CC
2Sleep 10 100+
3AP 11 Menu
4Volume + 12 Volume -
5Channel - 13 Channel +
6Numerical keys 14 OSD/OUT
7P.Channel 15 AV
8Stereo SAP 16 Mute
HPS-2909
5
2. TECHINICAL SPECIFICATION
Procedure to check up color TV electrical parameters
2.1 Audio
2.1.1 Output power at 10% THD
Connection through external video and audio input
a) TV setup in “PP” condition.
b)Connect a color bar generator (PAL-M system) to video input.
c) Connect an audio generator with 500mVAC level and 400Hz sinusoidal
frequency to audio input.
d)Connect to the power amplifier output a resistive load with equivalent Ohm
value of speaker used on the tested TV.
e) Connect a AC Voltmeter/Distortion Meter to the resistive load and increase
volume control until Distortion Meter reading be 10%. Measure voltage on
the resistive load and calculate power through next equation:
P = (V²/R)
Where “V” is voltage in VOLTS, “R” is resistive load in OHMS and “P” is
power in WATTS.
Mínimum Nominal Maximum Unit
4,50 5,00 -W
2.1.2 Residual Audio
a) TV setup in “PP” condition.
b)Apply 60dBµV signal (frequency and channel factory defined) to antenna
input modulated with white pattern at 87,5% and audio signal with 400Hz
frequency modulated in FM with 25kHz deviation.
c) Connect an oscilloscope to power amplifier output (connect for the
speaker).
d)Adjust volume to minimum.
e) Use the oscilloscope to measure peak-to-peak voltage, in Volt peak-to-peak
(Vpp).
Minimum Nominal Maximum Unit
- - 500 mVpp
HPS-2909
6
2.1.3 Audio frequency response in TV’s without tone control
a) TV adjustment condition:
üBalance center
üBass center
üTreble center
b)Connect a color bar generator (PAL-M system) to video-in.
c) Connect to the audio input TV - an audio generator adjust to 500 mVac
level, and sine wave 1kHz.
d)Connect to the output power amplifier a resistive load with the same value
of the impedance speaker.
e) Connect na AC voltmeter over the resistive load and adjust volume control
until obtain 1 Vac ).
f) Realign the audio generator to 100 Hz sine wave at the same level ( 500
mVac).
g)Read the new voltage in the resistive load and calculate the change in dB
through next equation:
A(100Hz)=20 log (VL/VREF)
The result is defined in“Decibel units “
h)Readjust the audio generator frequency to10 kHz at the same level.
i) Read the new voltage Vh at the resistive load and calculate the change in
dB through the next equation:
A(10kHz)=20logVH/VREF
Condition Minimum Nominal Maximum Unit
100Hz 2,00 6,00 10,00 dB
10kHz 0,00 +4,00 +8,00 dB
2.1.4 Áudio frequency response for the stereo television set with tonality
control
a) Repeat the above procedures (item 3) for the following additional
conditions:
Condition Minimum Nominal Maximum Unit
Bass control in max. position 100Hz +16,00 +20,00 +25,00 dB
Treble control in the meddle.10kHz -5,00 +7,00 +10,00 dB
Bass control in the min position. 100Hz -10,00 -3,00 +3,00 dB
Treble control in the meddle.10kHz -5,00 +7,00 +10,00 dB
Bass contr. in the meddle post.. 100Hz +4,00 +10,00 +15,00 dB
Treble control int the min pos.. 10kHz -15,00 -5,00 +10,00 dB
Bass contr. in the meddle pos. 100Hz +4,00 +10,00 +15,00 dB
Treble contr in the max. pos.. 10kHz +10,00 +15,00 +25,00 dB
HPS-2909
7
2.1.5 Channel separation in Stereo reception for the stereo television set
a) TV setup in PP condition.
b)Apply a 60dBmV signal (frequency and channel factory defined) with 88%
video modulation and audio stereo carrier modulation within the standard
“MTS” (BTSC).
c) Connect an AC double voltmeter at the audio output L-R.
d)Adjust the volume control to max. and the tremble, bass and balance to
middle position.
Note:
üDisconnect the speakers for more comfortable work.
e) Adjust the stereo generator for left channel only – with 30% modulation of
300 Hz sine wave and 7.5 kHz deviation.
f) Read the Double Voltammeter value Vac corresponding of Left and Right
channel and calculate the stereo separation trough the equate:
Sep (300Hz) L→R=20 log (VL/VR)
g)Adjust the stereo generator for left channel only – with 30% modulation of
3kHz sine wave and 7.5 kHz deviation.
Sep (3kHz) L→R=20 log (VL/VR)
i) Repeat the procedures e, f and g, and now select Right channel only, at the
same conditions above mentioned.
Sep(300Hz) R→L=20 log (VR/VL)
Sep(3kHz) R→L=20 log (VR/VL)
Condition Minimum Nominal Maximum Unit
Sep(300Hz) L →R15,00 - - dB
Sep(3kHz) L→R15,00 - - dB
Sep(300Hz) R→L15,00 - - dB
Sep(3kHz) R→L15,00 - - dB
2.1.6 Output and distortion level of S.A.P. signal
a) TV setup in PP condition.
b)Apply a 60dBµV signal ( Frequency and channel factory defined ) with 88%
video modulation, and Stereo / S.A.P audio signal carrier in accordance of
standard “MTS” (BTSC).
c) Connect na AC volt-distortion-meter at the Left channel.
d)Adjust the volume control to max. and the tremble, bass and balance to
middle position.
Note:
üDisconnect the speakers for more comfortable work.
HPS-2909
8
e) Adjust the Stereo/SAP generator for 400 Hz sine wave and 100%
modulation.
f) Active the SAP function in the Test Television.
g)Read Vac at the AC volt-distortion-meter.
h)Repeat all above procedures, connecting the volt-distortion-meter at the
Right channel
Minimum Nominal Maximum Unit
Output Level 450,00 500,00 550,00 mVAC
Distortion (THD) 0,20 1,00 1,50 %
2.1.7 AM Rejection
a) Connect at the IF sound input a FM generator adjust to 4.5 MHz modulated
with 400 Hz sine wave and +/- 25 kHz deviation and 90 dBuV level.
b)Connect na AC voltmeter in the audio detector output (after the emphasis
circuit) and read the VFM tension.
c) Connect at the IF sound input a AM generator pre-adjust to 4.5 MHz 30%
modulated with 400 Hz sine wave, and 90 dBuV level.
d)Read the Vam value in the voltmeter.
AMrejection will now be calculated by the equation:
RejAM = 20 log(VFM/VAM)
Note:
üBecause this parameter is designed to define only the
one circuit TV perform, the startup conditions adjust and
what’s circuits will be supplied, it will be defined
separately for each one model.
Minimum Nominal Maximum Unit
30,00 40,00 60,00 dB
2.2 POWER SUPPLY
2.2.1 Consume
Consume
a) Connect the TV under test through a electronic wattmeter at the
220Vac/60Hz line.
b)Turn-on the TV set and apply a 60dBµV ( the preferred channel must to be
defined by the production unit), modulated with a 88% video signal white
pattern, and a±25 kHz deviation FM carrier with a 400Hz sine wave audio
signal.
c) Adjust for max. the bright, contrast and volume controls, and read the Sink
Power show at the wattmeter.
d)Active Standby mode and read again the Sink power.
HPS-2909
9
e) Repeat all below procedures, connecting now the television under test to a
110Vac/60 Hz line.
Condition Minimum Nominal Maximum Unit
117VAC“PP” - - 125,00 W
117VACStand-By - - 3,00 W
234VAC“PP” - - 125,00 W
234VACStand-By - - 3,00 W
2.2.2 Main Power Supply
a) Connect the TV set under test to 110Vac/60Hz line.
b)Turn on the TV and apply a 60dBµV signal (frequency and channel defined
by factory) 88% modulated with white pattern and audio signal with 400Hz
frequency modulated in FM with ±25kHz of deviation.
c) Adjust the TV to a “PP” condition.
d)Utilizing a electronic DC voltmeter ( over 10 M input impedance), read the
next point in the power supply.
Condition Test Point Minimum Nominal Maximum Unit
“PP” 117VAC +B (Cathoe of D807) 130,50 132,50 134,50 VDC
“PP” 117VAC Áudio (Cathode of D808) 20,00 22,00 24,00 VDC
“PP” 117VAC Tuner (Cathode of DZ101) 30,00 33,00 36,00 VDC
“PP” 117VAC +5V (Emitter of Q101) 4,50 5,00 5,50 VDC
“PP” 117VAC +3V3 (Emitter of Q804) 3,00 3,30 3,60 VDC
“PP” 117VAC +8V6 Áudio (Emitter of
Q805) 8,00 8,60 9,00 VDC
“PP” 117VAC +8V Video (Cathode of
DZ807) 7,60 8,00 8,60 VDC
2.2.3 Main Power Supply Regulation with fluctuation of the line
Repeat the procedure of the item 1 when the television is connected to the
electric net with 100VAC/60Hz and also 220VAC/60Hz.
Condition Test Point Minimum Nominal Maximum Unit
“PP” 240VAC +B (Cathode of D807) 130,50 132,50 134,50 VDC
“PP” 240VAC Áudio (Cathode of D808) 20,00 22,00 24,00 VDC
“PP” 240VAC Tuner (Cathode of DZ101) 30,00 33,00 36,00 VDC
“PP” 240VAC +5V (Emitter of Q101) 4,50 5,00 5,50 VDC
“PP” 240VAC +3V3 (Emitter of Q804) 3,00 3,30 3,60 VDC
“PP” 240VAC +8V6 Áudio (Emitter of
Q805) 8,00 8,60 9,00 VDC
“PP” 240VAC +8V Vídeo (Cathode of
DZ807) 7,60 8,00 8,60 VDC
Table of contents
Other Durabrand TV manuals
Durabrand
Durabrand DWT2405 User manual
Durabrand
Durabrand TV-5 User manual
Durabrand
Durabrand DWT1905 User manual
Durabrand
Durabrand DCT3203 User manual
Durabrand
Durabrand DCT1303R User manual
Durabrand
Durabrand BH2004D User manual
Durabrand
Durabrand DCF2703 User manual
Durabrand
Durabrand DCT2405R User manual
Durabrand
Durabrand T6609BK User manual
Durabrand
Durabrand DBTV1300 User manual
Durabrand
Durabrand BH2004D User manual
Durabrand
Durabrand DBTV1341 Series User manual
Durabrand
Durabrand DCF2003 User manual
Durabrand
Durabrand CB130DR8 User manual
Durabrand
Durabrand DCT2405R User manual
Durabrand
Durabrand BH2004D User manual
Durabrand
Durabrand HPS-2971 User manual
Durabrand
Durabrand DCT1304R User manual
Durabrand
Durabrand DCT1904R User manual
Durabrand
Durabrand DCT1303R User manual
