Dukane 8934 User manual
1
Projector
User's Manual (detailed)
Network Guide
Thank you for purchasing this product.
This manual is intended to explain only the network function. For proper use of this
product, please refer to this manual and the other manuals for this product.
Features
This projector has the network function that brings you the following main features.
►Before using this product, be sure to read all manuals for this
product. After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
üWeb Control : allows you to monitor and control the projector through a network from a
computer. (&9)
üNetwork Bridge : allows you to control an external device through the projector from a
computer. (&40)
•
Microsoft
®
, Internet Explorer
®
, Windows
®
, Windows Vista
®
, Windows 7
®
, Windows 8
®
and
Aero
®
are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.
• Adobe®and Flash®are registered trademarks of Adobe Systems Incorporated.
• Pentium®is a registered trademark of Intel Corporation.
• JavaScript®is a registered trademark of Sun Microsystems, Inc.
• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
• Crestron®, Crestron e-Control®, e-Control®, Crestron RoomView®and RoomViewTM are
trademarks or registered trademarks of Crestron Electronics, Inc. in
the United States and other countries.
• Trademark PJLink is a trademark applied for trademark rights in
Japan, the United States of America and other countries and areas.
All other trademarks are the properties of their respective owners.
8934
C
430-8934-Net-00
2
Contents
Contents &
1. Connection to the network ...................................................... 4
1.1 System requirements ................................................................................. 4
1.1.1 Required equipment preparation ..................................................................................... 4
1.1.2 Hardware and software requirement for computer .......................................................... 4
1.2 Manual network connection setting - Wired LAN -. ..................................... 5
1.2.1 Equipments connection .................................................................................................... 5
1.2.2 Network settings .............................................................................................................. 5
1.2.3 “Internet Option” setting ................................................................................................... 8
2. Web Control .............................................................................. 9
2.1 Projector Web Control ............................................................................... 10
2.1.1 Logon ............................................................................................................................. 10
2.1.2 Network Information ....................................................................................................... 11
2.1.3 Network Settings ............................................................................................................ 12
2.1.4 Port Settings .................................................................................................................. 14
2.1.5 Mail Settings .................................................................................................................. 16
2.1.6 Alert Settings .................................................................................................................. 17
2.1.7 Schedule Settings .......................................................................................................... 19
2.1.8 Date/Time Settings ......................................................................................................... 21
2.1.9 Security Settings ............................................................................................................ 23
2.1.10 Projector Control .......................................................................................................... 24
2.1.11 Remote Control ............................................................................................................ 29
2.1.12 Projector Status ........................................................................................................... 30
2.1.13 Network Restart ........................................................................................................... 31
2.2 Crestron e-Control®.................................................................................. 32
2.2.1 Main window .................................................................................................................... 33
2.2.2 Tools window ................................................................................................................... 35
2.2.3 Info window ..................................................................................................................... 37
2.2.4 Help Desk window ........................................................................................................... 38
2.2.5 Emergency Alert .............................................................................................................. 39
3. Network Bridge Function ....................................................... 40
3.1 Connecting devices .................................................................................. 40
3.2 Communication setup ............................................................................... 41
3.3 Communication port ................................................................................. 41
3.4 Transmission method ............................................................................... 42
3.4.1 HALF-DUPLEX .............................................................................................................. 42
3.4.2 FULL-DUPLEX ............................................................................................................... 43
3
Contents
&
4. Other Functions ...................................................................... 44
4.1 E-mail Alerts ............................................................................................. 44
4.2 Event Scheduling ..................................................................................... 46
4.3 Command Control via the Network .......................................................... 49
4.4 Crestron RoomView®................................................................................. 54
5. Troubleshooting ..................................................................... 55
6. Warranty and after-sales service .......................................... 56
4
1. Connection to the network
1.1 System requirements
1. Connection to the network
The following equipments are required to connect the projector to your computer
through the network.
■ Common The projector: 1 unit, Computer : minimum 1 set
■ Depending on how you want to connect
LAN cable (CAT-5 or greater): 1 piece *1
1.1.1 Required equipment preparation
*1: The system for using the network function of the projector requires
communication environment conforming 100Base-TX or 10Base-T.
• The network communication control is disabled while the projector is
in standby mode if the STANDBY MODE item is set to SAVING. Please connect
the network communication to the projector after setting the STANDBY MODE
to NORMAL. (&SETUP menu in the Operating Guide)
NOTE
To connect your computer to the projector and use the network function of the
projector, your computer needs to meet the following requirements.
1.1.2 Hardware and software requirement for computer
üOS: One of the following.
Windows ® XP Home Edition /Professional Edition
Windows Vista ® Home Basic /Home Premium /Business /Ultimate /Enterprise
(Service Pack 1 or later)
Windows ® 7 Starter /Home Basic /Home Premium /Professional /Ultimate /
Enterprise
Windows ®8
Windows ® 8 Pro/Enterprise
üCPU: Pentium 4 (2.8 GHz or higher)
üGraphic card: 16 bit, XGA or higher
üMemory: 512 MB or higher
üHard disk space: 100 MB or higher
üWeb browser: Internet Explorer ®6.0 or higher
5
1. Connection to the network
1.2 Manual network connection setting - Wired LAN -
This section explains how to set it up manually.
1.2.1 Equipments connection
Connect the projector and a computer with a LAN cable.
* Before connecting with an existing network, contact the network administrator.
Next, check the following computer settings.
1.2.2 Network settings
This is an explanation of network connection settings for Windows®7.
1) Log on to Windows®7 as administrator authority. Administrator authority is the
account, which can access to all functions.
2) Open “Control Panel” from “Start” menu.
3) Open “View network status and tasks” in “Network and Internet”.
With the icons in the "Control Panel" window displayed, click "Network and
Sharing Center".
4) Click "Change adapter settings" in the menu
on the left side of the "Network and Sharing
Center" window.
(continued on next page)
6
1. Connection to the network
1.2 Manual network connection setting - Wired LAN - (continued)
7) Select "Use the following IP address" and congure the IP
address, Subnet mask and Default gateway for the computer
accordingly. If a DHCP server exists in the network, you
can select "Obtain an IP address automatically" and the IP
address will be assigned automatically.
After setting is complete, click [OK] to close the window.
5) Right-click "Local Area Connection" to open the menu,
and select "Properties".
6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click
[Properties].
(continued on next page)
7
1. Connection to the network
1.2 Manual network connection setting - Wired LAN - (continued)
[About IP address]
■ Setting manually
The Network address portion of the IP address setting on your computer must
be the same as the setting on the projector. Also, the entire IP address on the
computer must not overlap with that of the other devices on the same network,
including the projector.
The projector’s settings are as follows.
IP address: 192.168.1.254
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
Therefore, specify the computer’s IP address as follows.
IP address: 192.168.1.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
For example
Select from 1 to 254 for “xxx” not duplicating with any other equipments.
In this case, since the IP address of the projector is “192.168.1.254”, specify a
setting between 1 to 253 for the computer.
• “0.0.0.0” cannot be set to the IP address.
• The projector’s IP address can be changed by using the conguration utility
via a web browser. (&12)
• If the projector and the computer exist in the same network (i.e., same
network address), you can leave the default gateway eld blank.
• When the projector and the computer exist in different networks, the default
gateway must be set. Consult to the network administrator in detail.
NOTE
■ Setting automatically
When a DHCP server exists in the connected network, it is possible to assign an
IP address to the projector and computer automatically.
* DHCP is abbreviation for “Dynamic Host Conguration Protocol” and has
the function to provide necessary setting for network like IP address from
server to client. A server that has DHCP function is called DHCP server.
(continued on next page)
8
1. Connection to the network
1.2 Manual network connection setting - Wired LAN - (continued)
2) Click “Connections” tab and then click [LAN settings] button
to open “Local Area Network (LAN) Settings”.
1.2.3 “Internet Option” setting
1) Click “Internet Options” in “Network and
Sharing Center” window to open “Internet
Properties” window.
3) Uncheck all boxes in “Local Area Network (LAN) Settings”
window.
After setting is complete, click [OK] to close the window.
9
You can adjust or control the projector via a network from a web browser on a
computer that is connected to the same network.
• Internet Explorer®6.0 or later is required.
• If JavaScript® is disabled in your web browser conguration, you must enable
JavaScript® in order to use the projector web pages properly. See the Help les
for your web browser for details on how to enable JavaScript®.
• It is recommended that all web browser updates are installed.
NOTE
2. Web Control
2. Web Control
Refer to the following for conguring or controlling the projector via a web browser.
Make sure that your computer and the projector is connected via network, and
then start Web browser.
Enter the projector's IP address into URL input box of the Web browser as the
example below, and then press the Enter key or button.
Example: If the IP address of the projector is set to 192.168.1.10:
Enter “http://192.168.1.10/” into the address bar of the web browser
and press the Enter key or click button.
If a correct URL is input, and the
projector and your computer are
connected to the same network
correctly, the selection window as
shown on the right will be displayed.
You can choose to use Projector Web
Control or Crestron e-Control®as a tool
for controlling the projector. Click one of
them.
For more details, refer to 2.1 Projector
Web Control (&10) or 2.2 Crestron
e-Control®(&32).
• If Crestron e-Control in the Network Settings (&12) is set to
Disable, the selection window above does not appear, but the Logon window of
the Projector Web Control is displayed.
• Crestron e-Control®is created using Flash®. You need to install Adobe®Flash®
Player on your computer to use Crestron e-Control®.
NOTE
10
2. Web Control
2.1.1 Logon
To use the Projector Web Control function, you need
to logon with your user name and password.
• The language used on the Projector Web Control screen is the
same as that of the OSD on the projector. If you want to change it, you need
to change the OSD language on the projector. (&SCREEN menu in the
Operating Guide)
NOTE
Below are the factory default settings for user
name and password.
User name Administrator
Password <blank>
Enter your user name and password, and then click the [OK].
If you logon successfully, the screen below will be displayed.
Main menu
Click the desired operation or conguration item on the main menu.
2.1 Projector Web Control
Logon window
Other manuals for 8934
3
Table of contents
Other Dukane Projector manuals
Dukane
Dukane 8950WUSS User manual
Dukane
Dukane ImagePro 9060 User manual
Dukane
Dukane ImagePro 8753 User manual
Dukane
Dukane 6530WB User manual
Dukane
Dukane 8527 User manual
Dukane
Dukane 8950W User manual
Dukane
Dukane ImagePro 8807 User manual
Dukane
Dukane ImagePro 8105H User manual
Dukane
Dukane ImagePro 8783 User manual
Dukane
Dukane 6530B User manual
Dukane
Dukane 8957WA User manual
Dukane
Dukane 8980WU User manual
Dukane
Dukane ImagePro 8776-W User manual
Dukane
Dukane ImagePro 6765WU User manual
Dukane
Dukane 8958A User manual
Dukane
Dukane 8980WU User manual
Dukane
Dukane 6537WC User manual
Dukane
Dukane 28A8751 User manual
Dukane
Dukane 8755K User manual
Dukane
Dukane ImagePro 8063 User manual
