Dormakaba STV 2 Series User manual
WN 059506 45532 – 2019-03
EN
STV2xx
Mounting instructions
1 About this manual
1.1 Target group
The STV2xx door lock must only be mounted by
trained electricians with specific knowledge of
electromechanical locks, fire safety codes and
regulations.
1.2 Intended use
The STV2xx is used to keep doors securely closed, and
to open them without delay in case of emergency. The
STV2xx is used in the SafeRoute® system.
1.3 Other applicable documents
• System instructions for the used SafeRoute® license
• Operating instructions for the SafeRoute® system
• Inspection logbook
1.4 Symbols used
ATTENTION
This signal word indicates a situation of
potential risk, which could lead to damage
to property or the environment if not
averted.
TIPS AND RECOMMENDATIONS
This signal word indicates useful information
for efficient and trouble-free operation.
1.5 Further labeling
1. 2. Sequence of action steps
6Reference to a chapter
Reference to another document
Door opening direction DIN left =
opening outwards to the right
Door opening direction DIN right =
opening outwards to the left
Components may be damaged by
electrostatic discharges
1.6 Tool symbols
Allen wrench,
e.g. wrench opening 3
2 Safety
ATTENTION
Property damage by electrostatic discharge.
The control board may be damaged by an
electrostatic discharge!
• The user must ground her/his own body
before touching a component!
Contents
1 About this manual 1
2 Safety 1
3 Product description 2
4 Mounting 2
5 Assignment of terminals and switches 7
6 Dismantling and disposal 7
3 Product description
The STV 2xx is an electromagnetic lock for swing
doors on escape routes and is mounted on the door
frame . Together with a SafeRoute® Control Unit
(SCU), the door lock forms an escape route security
system.
The STV 2xx includes a surface holding magnet with
high locking force with small dimensions.
The maximum locking force complies with Directive
for Electrical Locking Systems on Escape Route Doors
(EltVTR).
They may only be mounted on fire and smoke
protection doors, if the usability certificates for these
doors provide for the mounting, and if the related
requirements are followed. Additional notes can also
be found in the notification “Permitted changes and
supplements to fire protection closures” of the
Deutsches Institut für Bautechnik (DIBt), Berlin.
3.1 Variants
The XX markings are color variants. The instructions
are valid for the STV 201 (silver) and STV 211 (white).
3.2 LED displays
LED on LED off LED flashes
DCW® LED (red)
Bus connection OK
Bus connection interrupted
DCW® error (see SafeRoute®
system instructions)
Config LED (yellow)
Configuration successful
Device not configured
Both LEDs
Configuration mode active
3.3 Technical data
Supply voltage: 24 V DC +/-15 %
Retention force 2000 N bei Unenn +/- 10 %
Power consumption: locked: 200 mA
unlocked: 20 mA
Temperature range: -10°C to +55 °C
Rel. Humidity: up to 93 %
(non condensing)
Degree of protection: IP 30
4 Mounting
TIPS AND RECOMMENDATIONS
The mounting is shown on a door which
opens outwards to the left (DIN right).
• Proceed in mirror-inverted order when
mounting a DIN left door.
2STV2xx 2019-03
WN 059506 45532
dormakaba Mounting instructions Product description
1
3
4
3STV2xx 2019-03WN 059506 45532
dormakaba Mounting instructions Product description
2
DIN left =
opening
outwards
to the right
DIN right =
opening
outwards
to the left
Drilling
template
optional for door contact
4STV2xx 2019-03
WN 059506 45532
dormakaba Mounting instructions Product description
7
1.
2.
6B
5
1.
2.
6A
1.
2.
9
≤ 15mm
10
5STV2xx 2019-03WN 059506 45532
dormakaba Mounting instructions Product description
8
1.
2.
3.
6STV2xx 2019-03
WN 059506 45532
dormakaba Mounting instructions Product description
11
1.
5
2.
12
5 Assignment of
terminals and
switches
Config LED
(yellow)
DCW® LED
X1 Connections to the locking magnets
X2 inner tappet contact
X4 24 V DC
GND
DCW®-Bus SCU-xx
external TK or bridge
S1 Housing tampering contact
S2 DIP switch for setting the component
address (see SafeRoute® system
instructions).
DCW®
address
Switch S2
1
2
3
4
0
1
0
1
0
0
1
1
S3
BS
Service switch for suppression of
tampering alarm
B = Operation (housing tampering
contact activated)
S = service (Housing tampering contact
shut off)
S4 Service button
Press service button for 8 seconds =
original settings
6 Dismantling and
disposal
Dismantling is carried out in reverse order of the
mounting instructions.
The product must not be disposed of in
domestic waste.
The product must be disposed of in an
environmentally friendly manner at the
arranged take-back and collection points.
Refer to the statutory regulations for your country.
Electrostatically
sensitive
components
7STV2xx 2019-03WN 059506 45532
dormakaba Mounting instructions Assignment of terminals and switches
dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: +49 2333 793-0 F: +49 2333 793-4950 www.dormakaba.com
Translation of the original document, subject to change without notice
This manual suits for next models
1
Table of contents
Other Dormakaba Lock manuals
Dormakaba
Dormakaba UNIVERSAL Light US 10 User manual
Dormakaba
Dormakaba M Series User manual
Dormakaba
Dormakaba Axessor Series User manual
Dormakaba
Dormakaba LA GARD ComboGard Pro 39E Manual
Dormakaba
Dormakaba Classic User manual
Dormakaba
Dormakaba Saflok Quantum Pixel User manual
Dormakaba
Dormakaba YD30D Manual
Dormakaba
Dormakaba ORACODE 480 Series User manual
Dormakaba
Dormakaba LA GARD 700 Series User manual
Dormakaba
Dormakaba LA GARD 700 Series User manual
Dormakaba
Dormakaba LA GARD ComboGard Pro 39E Manual
Dormakaba
Dormakaba Cobalt Single User manual
Dormakaba
Dormakaba 79 Series Assembly instructions
Dormakaba
Dormakaba LA GARD 700 Series User manual
Dormakaba
Dormakaba La Gard Reset Box User manual
Dormakaba
Dormakaba SafeRoute-System Mini User manual
Dormakaba
Dormakaba SL30DBL Cobalt Double User manual
Dormakaba
Dormakaba YD30S Manual
Dormakaba
Dormakaba STV 1 Series User manual
Dormakaba
Dormakaba Axessor CIT User manual
