Dormakaba ED900 User manual

ED900 108125350 www.dormakaba.com 02-2020

Quick Start Guide

ED900

• The ED operator must be completely installed

per the applicable dormakaba USA Inc. ED

Installation Instruction Manual.

• Door must be closed.

• Both program switches in the CLOSE “” position.

Step Directions Expected results



Power switch to ON position.

• A series of numbers and letters will show

up on the display.

• This will stop after two horizontal dashes

side by side move up and down several

times.



While the dashes are moving up and down,

press the bottom button on the display.

• This will identify which way the unit is

mounted.

• Letters and numbers will now display

right side up.

The display will show a “P“ on the right with

a rotating segment on the left.

When the braking circuit plug is in the

correct position the door will easily Press

open and close slowly. If the door is very

hard to Press open change the jumper

position.

> 3s Reset

< 3s Quit

> 3s

PRG

< 3s LEARN

Fact-Setup

> 3s

> 8s



Press and hold the right button until Parameter

ID is displayed (approximately  seconds), then

release the button.

Parameter ID will appear (ex. AS).

Press the right button. Displays the current setting.

Press the right button again. Display will flash the current setting.

Press the up and down buttons to change the

setting.

Press the right button to accept the changes. Displays the new parameter

setting.

Press the left button to return to the

programming menu.

Displays the current Parameter ID

(Step ).



Press the down button to go to the next

parameter setting (or) Go back to Step .

Press the left button to exit programming menu. Display will show a rotating

segment and a “”.

NOTICE

This guide is intended to be used as a reference to assist in

programming the dormakaba ED operator in accordance with

ANSI A. Standard for Low Energy Power Operated Doors.

Braking circuit plug position

A – Pull arm B – Press arm

Power fail closing speed.

• The door must be adjusted to close in

no less than three seconds but a

minimum of five seconds is recommended.

WARNING

If braking circuit plug is inserted

incorrectly, brake circuit will not

work. The door can close at high

speed!

WARNING

Verify power fail closing speed

and braking circuit plug position

before programming the door

and completing a learn cycle.

All three required

parameter settings

(AS, rd, Tb) must

be made to flash

even if the value

does not need to

be changed before

the door will move

to the learn cycle.

ED900 208125350 www.dormakaba.com

T: 717-336-3881 02-2020

Step Configuration

Parameter

Range

Factory

Settings

* Factory setting.

 Installation

type -

0* Pull arm with track, wall mounting

on pull (hinge side).

Press arm, wall mounting on

approach (non-hinge side).

Press arm with track, wall mounting

on approach (non-hinge side).

Overhead concealed (OHC) right

hand.

 Overhead concealed, left hand.



Reveal

depth

ED

- to  0*

Reveal depth rd is set in increments

of  mm (/”).

Example:  =  mm ( /”)

 Door width ED

 to  10*

The astragal is included in the door

width.

Door width Tb is set in increments

of  mm (”).

Example:  =  mm (”).

Reveal depth rd

Door width Tb

rd Inches

- -  /

- -/

- -/

 

 /

 /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

  /

 

  /

  /

Tb Inches

 

 



 

 

 

Step

Learn Cycle.

A ““ displayed on the right side and a rotating segment

on the left indicates the unit is ready for a learn cycle.



To start the learn cycle, press and hold the bottom button

until the display changes (approximately three seconds).

• The door will make several movements and the display

will cycle through several letters and numbers.



When the display stops at “” push the door open to the

desired opening angle between  and  degrees, then

let go of the door.

Press the bottom button to continue the learn cycle.

The operator will complete the learn cycle.

• When finished, there will be two horizontal bars side by

side on the display.

You can now continue with the programming and

customize the door as desired.

Spring force too low.

If the door closes and an “F” is displayed, this is an

indication that the spring force is too low.

. Turn off the power.

. Increase the spring force.

• The spring should have a minimum of  turns and a

maximum of  turns, depending on door width and

weight.

. Restart the learn cycle (Step ).

Other manuals for ED900

Other Dormakaba Door Opening System manuals

Dormakaba

Dormakaba UNIVERSAL GK 50 User manual

Dormakaba

Dormakaba 8600T EMR User manual

Dormakaba

Dormakaba ED900 User manual

Dormakaba

Dormakaba HSW-R User manual

Dormakaba

Dormakaba G-SR/BG Series User manual

Dormakaba

Dormakaba TS 98 XEA User manual

Dormakaba

Dormakaba TS 93 G EN 2-5 User manual

Dormakaba

Dormakaba ED900 User manual

Dormakaba

Dormakaba PORTEO User manual

Dormakaba

Dormakaba 8900 FH User manual

Dormakaba

Dormakaba 8907 AF PKT User manual

Dormakaba

Dormakaba TS9356 PKT 120/170 User manual

Dormakaba

Dormakaba ED100 User manual

Dormakaba

Dormakaba ED50 User manual

Dormakaba

Dormakaba 8900 PT User manual

Dormakaba

Dormakaba 7400 SIS User manual

Dormakaba

Dormakaba ES 200 EASY PLUS User manual

Dormakaba

Dormakaba ED900 User manual

Dormakaba

Dormakaba ED900 User manual

Dormakaba

Dormakaba ED50 User manual

Dormakaba

Dormakaba ED250 User manual

Dormakaba

Dormakaba Best SL6000 SIS User manual

Dormakaba

Dormakaba TS 98 XEA User manual

Dormakaba

Dormakaba ED50 User manual

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual