Domestia DME-LAN-002 User manual
www.domestia.be
USERS MANUAL
DME-LAN-002 |
Master control module
2
3
CONTENTS
1 DESCRIPTION .............................................................................................. 4
2ELECTRICAL CONNECTION OF THE DMELAN002......................................... 5
3 NETWORK CONNECTION............................................................................. 8
3.1 Configuration of the IP address.................................................................. 8
3.2 Creation of a network................................................................................. 9
3.3 Wi-Fi router................................................................................................... 10
4LAUNCHING THE INSTALLER APPLICATION................................................... 11
4.1 Launch......................................................................................................... 11
4.2 Choice of installer language...................................................................... 12
4.3 Enter your installer details ......................................................................... 12
4.4 Details of the installation............................................................................ 13
4.5 Reading the content of the DME-LAN-002................................................... 14
4.6 Installation composition............................................................................. 14
4.7 Configuring the slave cards....................................................................... 16
4.8 Configuring the output names.................................................................... 18
4.9 Configuration of the group.......................................................................... 19
4.10 Configuring areas....................................................................................... 23
4.11 Configuring temperature sensors............................................................... 23
4.12 Saving the configuration in the DME-LAN................................................... 25
4.13 X.X Bus DMX 512........................................................................................ 26
5PROGRAMMING THE PUSHBUTTONS............................................................ 27
5.1 Programming outputs................................................................................. 27
5.2 Programming groups.................................................................................. 27
6 USER INTERFACE LOCAL............................................................................ 28
6.1 «Home» menu.............................................................................................. 29
6.2 «Temperature» menu................................................................................... 29
6.3 «Events» menu............................................................................................ 30
6.4 «Parameters» menu.................................................................................... 33
7 USER INTERFACE: HOME ON WEB................................................................. 34
8TROUBLESHOOTING...................................................................................... 37
9 WARRANTIES................................................................................................ 38
4
1. DESCRIPTION 1
The DME-LAN-002 is a comprehensive system that integrates the following elements (see
Figure A on page 4) :
• Ethernet port (RJ45)
• RS485 communication port (A, B and GND)
• Bus line for identification modules DMI-006-001, DMI-004-001 or DMI-LED-004 (Line
• 1, Line 2, Line 3 and Line 4)
• Bus line for temperature sensors
• 230VAC power input
The DME-LAN-002 allows the following elements on its home-automation system, which
will be configured as «slaves» :
• Lighting-management cards (DMC-012-002, DMC-012-016)
• Shutter-control cards (DMCV-006-002)
• 4-output extension modules (DML-004-002, DMA-004-003, DMT-004-003, DMD-004-001
• DMC-004-003 or DMCV-002-003). Please refer to the relevant instruction manuals for
more information.
• Collection of information from the temperature sensor(s) (DMCT-001-001)
The Home Manager application is available for free from the Android, Apple and
Windows stores.
It loads web pages that the user can open with any Internet browser (Safari, Chrome,
Firefox, Internet Explorer, Opera, etc.).
If it is connected to the Internet via its Ethernet port (RJ45), the remote server («Home on
Web») allows:
• remote management.
• firmware updates (version of the card’s soware).
• saving of installation data.
• enrichment of the graphic interface.
• synchronisation of the system’s internal clock (automatic switching to summer/
winter time), based on international atomic time.
The DME-LAN-002 has 4 input buses and can manage up to 240 commands1via
identification modules (DMI-006-001, DMI-LED-006) that are distributed over the 4 buses.
We recommend one bus per level, in order to make the installation process easier.
1 Sixty commands are available per bus. This includes unique lighting or shutter/blinds
commands (point by point + groups, scenarios).
5
There are LED indicators (one blue LED and one red LED) next to the line
connectors. The blue LED lights up when the pushbutton (PB) for the line is pressed;
the red LED lights up when there is a short circuit on the latter.
2. ELECTRICAL CONNECTION 1
The DME-LAN-002 card is powered directly by the 230 VAC mains. The input voltage
range is 100–240 VAC and 50–60 Hz.
From the DME-LAN-002 card, the identification modules are connected via two
wires.
There is no polarity to consider. They can be wired either:
• by bus.
• in a star or triangle configuration.
• both, simultaneously.
Figure A below shows the DME-LAN-002 with the connection principle for the
dierent outputs:
• Slave cards can be connected to the DME-LAN-002, via the RS485 bus to
terminals 6(A), 7(B), 8(GND) (RS485 Slave). In order to do this, use the UTP
cable (recommended), the VVT cable or the VOB cable, etc. To create a link
between remote cards in dierent boxes, it is best to use a UTP cable, with a
pair for terminal 6(A) and 7(B) and a pair for terminal 8 (GND).
• Terminals 1, 2 and 3 (RJ45) make it possible to connect the DME-LAN-002
card to the Ethernet network directly to a DET-005-002 touch screen, or via a
network switch to allow the DET-005-002 touch screen, smartphone or tablet
to access the home-automation system. Use a UTP Cat5e cable (minimum).
• The DMCT-001-001 temperature sensors are connected to terminals 27–31
(«RS485 Captor»and «16V Captor». The power supply for the latter is
provided by the DME-LAN-002). Use a UTP cable (recommended), a VVT
cable or a VOB cable, etc.
• As explained in chapter 2, the identification modules are connected on the
«Line» inputs. Each «Line» input can be used to program a maximum of 60
dierent functions. It is preferable to divide the modules into several circuits
over 4 lines. Wiring the identification modules: Two non-polarised wires (UTP,
VVT, XVB, VOB, etc). (Be careful of the quality of the connection: the cross-
section of the identification module wires is 0.6mm²).
• The 230 VAC power supply is connected to terminals 24(L) and 26(N)
6
P
hN
IN
230 VAC
A B
D
G
N
1 2 3
IN 100-240V /50-60 Hz
L
ta -10°c to +45°c
N
www.domestia.be
Made in Belgium
DME-LAN-002
2625
A
D
G
N
RS485 Captor
27 28 29 30 31
B
D
G
N
+
16
V
+12 V
Captor
39 40 43 44 47 48 51 52
Line 1 Line 2 Line 3 Line 4
24
NC
RJ45
6 7 8
A
G
BD
N
RS485
Slave
To temperature sensor
(see instructions for use)
To identification modules
(DMI-004-001, DMI-006-001, of DMI-LED)
A B GND
RS485
to other card (s)
Connection
ethernet
7
Example of the DME-LAN-002 Connection
A B
D
G
N
1 2 3
IN 100-240V /50-60 Hz
L
ta -10°c to +45°c
N
www.domestia.be
Made in Belgium
DME-LAN-002
2625
A
D
G
N
RS485 Captor
27 28 29 30 31
B
D
G
N
+
16
V
+12 V
Captor
39 40 43 44 47 48 51 52
Line 1 Line 2 Line 3 Line 4
24
NC
RJ45
6 7 8
A
G
BD
N
RS485
Slave
IN 230V~ 50 Hz
L
OUT1 OUT2
2,6W ta -10°c to +45°c
OUT3 OUT4 N
D
A B G
RS485
N
250 W 250W 250W 250W
RS1
T1 T2 T3 T4
charge
setting
1 2 3 4
ON DIP
RS2
27 28 30 31 33 34 36 37 50 51 52
22 23 25 26
IN1
IN2
IN3
IN4
ALL OFF
8 9 10 11
ALL ON
12 13
JP1
Standalone Inputs
(Remove JP1)
DML-004-002
ON DIP
DMC-012-002
A
B
C
D
E
*(1)
1 2 3 4 5 6 7 8 9 10 11 12
Gauche Droite
Haut
Bas
Centre
8A8A8A8A8A 8A 8A 8A 8A 8A 8A8A
A
G
D
N
B
DMC-012-002
A
B
C
D
E
*(1)
1 2 3 4 5 6 7 8 9 10 11 12
Gauche Droite
Haut
Bas
Centre
8A8A8A8A8A 8A 8A 8A 8A 8A 8A8A
A
G
D
N
B
UTP,
VVT
LN
LN
LN
Ph N
IN 230VAC
8
Example of the connection for identification modules (see the instruction manual
for the DMI-LED-004 identification modules)
3. NETWORK CONNECTION
3.1. CONFIGURATION OF THE IP ADDRESS
When you switch the DME-LAN on, if it is connected to a modem or router, it will
automatically adapt its IP address to be compatible with the network used (if it is
not connected to a router, it will be configured to IP address 192.168.1.210).
9
For example:
• For Proximus modems, it will receive the following kind of address: 192.168.1.210).
• For Voo or Telenet modems, it will automatically change to the IP address
192.168.0.210.
However, it is possible to configure the network parameters of the DME-LAN manually, via
the address http://192.168.1.210.
3.2.CREATION OF A NETWORK
No Internet connection is required to configure the DME-LAN. However, you must
connect it directly to your PC via a wired network (in this case, the PC’s IP address must
be configured manually) or via a Wi-Fi router (for example, a DRW-001-001-type router –
see point 3.3).
Below: the local page configuration parameters for the DME-LAN-002
IP:192.168.1.210
Modem/Switch
IP:192.168.1.1
DME-LAN-002
IP:xx.xx.xx.xx
IP:192.168.1.2
IP:192.168.1.3 IP:192.168.1.4
Internet
Serveur
my.domestia.be
Local Network
10
3.3. DRW001001 WIFI ROUTER
The «DRW-001-001» module is a pocket Wi-Fi router. It is specially configured to be
connected directly to our supplementary management unit (DME-LAN-002) and can be
programmed for Wi-Fi before having Internet access.
Ultra compact and equipped with a mini USB port, this router can also be powered using
a laptop, an AC adapter or a Power Bank (1A)
Connecting your DME-LAN-002 to the DRW-001-001 router :
• Connect as indicated in the diagram below.
• Check that the switch is set to «3G/4G» mode.
• Connect your device (tablet/phone/computer) to the network indicated on the
router label via Wi-Fi (SSID: «TP-LINK_…»).
• Enter the password indicated on the router label. (Key: «******»).
• Launch Home Manager and click on the magnifying glass in the settings to check
for the presence of the management unit (DME-LAN-002) on the network.
• The drop-down list displays the DME-LAN available (connected to the network).
• If you are unable to connect, check your connection by going to your
management unit’s local page (DME-LAN-002) from your web browser (IP address:
192.168.1.210 or 192.168.0.210).
»If the page opens, you can close it, then launch Home Manager again.
»Otherwise, check that you are connected to the Wi-Fi «TP-LINK_...» and restart
your management unit (DME-LAN-002) using the small white button on the side
of the ABGND «RS485 Slave» terminal; one of the two devices is probably not
connected properly.
Table of contents
Other Domestia Control Unit manuals
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
