DMX4ALL DMX-Servo-Control 2 User manual
DMX-Servo-Control 2
User Manual
DMX-Servo-Control 2 2
For your own safety, please read this user manual and warnings carefully
before installation.
Description
The DMX-Servo-Control 2 is designed for controlling of two servos via DMX.
Two Servos
The DMX Servo Control 2 has two servo ports. Each can be controlled via one DMX
channel.
Servos with 5V up to 12V DC can be used
The supply voltage of the DMX-Servo-Control 2 is between 5V and 12V.
Servos with a supply voltage within this range can be connected directly.
Adjustable Servo control signal
The controlling occurs via an adjustable pulse width.
Compact Design
The design and the compact construction allows an installation of this small
assembly in areas that do not offer much space.
LED-Display
The integrated LED is a multifunctional display for showing the current device status.
DMX Addressing
The DMX addressing is settable via a 10-position DIP switch.
RDM Support
The DMX Servo Control 2 allows configuration via RDM over DMX.
DMX-Servo-Control 2 3
Data sheet
Power supply: 5-12V DC
50mA without connected servo
Protocol: DMX512
RDM
Servo-Voltage: 5-12V DC (corresponds to the supply voltage)
Servo-Power: max. 3A in sum for both servos
DMX-Channels: 2 Channels
Connection: 1x screw terminal / 2pin
1x screw terminal / 3pin
2x pin header RM2,54 / 3pin
Dimension: 30mm x 67mm
Content
1x DMX-Servo-Control 2
1x Quick manual german and english
DMX-Servo-Control 2 4
Connection
ATTENTION :
This DMX-Servo-Control 2 is NOT ADMITTED for applications whom has
safety-relevant requirements or in which dangerous situations can occur !
DMX-Servo-Control 2 5
LED-Display
The integrated LED is a multifunction display.
During to the normal operation mode the LED lights permanently. In this case the
device is working.
Furthermore, the LED shows the current status. In this case the LED lights up in
short pitches and then is missing for longer time.
The number of the flashing lights is equal to the event number:
Status
-
Number
Error
Description
1 No DMX There is no DMX-Address
2 Addressing
error
Please check, if a valid DMX-Start Address
is adjusted via the DIP-Switches
4 Configuration
stored
The adjusted configuration is stored
DMX-Servo-Control 2 6
DMX-Addressing
The Start Address is adjustable via DIP-Switches.
Switch 1 has the valency 2
0
(=1), switch 2 the valency 2
1
(=2) and so on up to
switch9 with the valency 2
8
(=256).
The sum of the switches showing ON is equal to the start address.
Address
Switch Address
Switch
1
ON
OFF
12345678910
... ...
2
ON
OFF
12345678910
508
ON
OFF
12345678910
3
ON
OFF
12345678910
509
ON
OFF
12345678910
4
ON
OFF
12345678910
510
ON
OFF
12345678910
5
ON
OFF
12345678910
511
ON
OFF
12345678910
The DMX start address can be also adjusted via the RDM parameter
DMX_STARTADDRESS. For RDM operation all switches must be set to OFF !
DMX-Servo-Control 2 7
Servo control signal
The signal which is send to the Servo consists of a High-Impulse and a Low one. The
pulse duration is important for the Servo.
Normally this impulse is between 1ms and 2ms, which is also the standard setting for
the DMX-Servo-Control 2. These are the end positions of the Servos where it is not
limited mechanically. A pulse length of 1.5ms would be the Servo middle position.
1,5ms
2ms (max)
1ms (min)
→Servo is positioned left
→Servo is positioned right
→Servo is positioned centred
DMX-Servo-Control 2 8
Adjust Servo control signal
In according to the used Servo it can be advantageous to adapt the impulse-times.
The minimum time for the left position can be set within the range 0,1-2,5ms. The
maximum time for the right position must be bigger than the minimum time and can
be maximum 2,54ms.
Please proceed as following for the settings:
-Turn on the DMX-Servo-Control
-Set DIP-Switch 9 and 10 on OFF
-Set DIP-Switch 10 on ON
-Set via the DIP-Switched 1-8 the Minimum time
-Set DIP-Switch 9 on ON
-Set via the DIP-Switched 1-8 the Maximum time
-Set DIP-Switch 10 on OFF
-The LED lights up 4x as confirmation that the settings are stored
-Set via DIP-Switches 1-9 the DMX-Starting address
The time-setting takes place with the DMX-Addressing via the DIP-Switches in 10µs
steps. Thereby the set value with 0,01ms is multiplied, so for example a value of 100
results in a value of 1ms.
1,00ms
= 100 x 0,01ms
2,52ms
= 252 x 0,01ms
1,01ms
= 101 x 0,01ms
2,53ms
= 253 x 0,01ms
1,02ms
= 102 x 0,01ms
2,54ms
= 254 x 0,01ms
The RDM parameters LEFT_ADJUST and RIGHT_ADJUST can also be used
to set the pulse time.
DMX-Servo-Control 2 9
RDM
(from Hardware V2.1)
RDM is the short form for Remote Device Management.
As soon as the device is within the system, device-dependent settings occur remotely
via RDM command due to the uniquely assigned UID. A direct access to the device is
not necessary.
If the DMX start address is set via RDM, all address switches at the DMX-
Servo-Control 2 must be set to OFF ! A DMX start address set by the address
switches is always prior !
This device supports the following RDM commands:
Parameter ID
Discovery
Command
SET
Command
GET
Command
ANSI/
PID
DISC_UNIQUE_BRANCH
E1.20
DISC_MUTE
E1.20
DISC_UN_MUTE
E1.20
DEVICE_INFO
E1.20
SUPPORTED_PARAMETERS
E1.20
PARAMETER_DESCRIPTION
E1.20
SOFTWARE_VERSION_LABEL
E1.20
DMX_START_ADDRESS
E1.20
DEVICE_LABEL
E1.20
MANUFACTURER_LABEL
E1.20
DEVICE_MODEL_DESCRIPTION
E1.20
IDENTIFY_DEVICE
E1.20
FACTORY_DEFAULTS
E1.20
DMX_PERSONALITY
E1.20
DMX_PERSONALITY_DESCRIPTION
E1.20
DISPLAY_LEVEL
E1.20
DMX_FAIL_MODE
E1.37
DMX-Servo-Control 2 10
Parameter ID
Discovery
Command
SE
T
Command
GET
Command
ANSI/
PID
SERIAL_NUMBER
1)
PID:
0xD400
LEFT_ADJUST
1)
PID:
0xD450
RIGHT_ADJUST
1)
PID:
0xD451
1) Manufacturer depending RDM control commands (MSC - Manufacturer Specific Type)
Manufacturer depending RDM control commands
:
SERIAL_NUMBER
PID: 0xD400
Outputs a text description (ASCII-Text) of the device serial number.
GET Send: PDL=0
Receive: PDL=21 (21 Byte ASCII-Text)
LEFT_ADJUST
PID: 0xD450
Sets the high time length for left servo position.
GET Send: PDL=0
Receive: PDL=2 (1 Word LEFT_ADJUST_TIME)
SET Send: PDL=2 (1 Word LEFT_ADJUST_TIME)
Receive: PDL=0
LEFT_ADJUST_TIME
Fun
k
tion
200 - 5999 WERT x 0,5µs = Impulszeit LINKS
Default: 2000 (1ms)
RIGHT_ADJUST
PID: 0xD451
Sets the high time length for right servo position.
GET Send: PDL=0
Receive: PDL=2 (1 Word RIGHT_ADJUST_TIME)
SET Send: PDL=2 (1 Word RIGHT_ADJUST_TIME)
Receive: PDL=0
LEFT_ADJUST_TIME
Fun
k
tion
201 - 6000 WERT x 0,5µs = Impulszeit RECHTS
Default: 4000 (2ms)
Table of contents
Other DMX4ALL Computer Hardware manuals
DMX4ALL
DMX4ALL MaxiRGB User manual
DMX4ALL
DMX4ALL ArtNet-DMX TWIN PoE User manual
DMX4ALL
DMX4ALL ArtNet-DMX Mux24 User manual
DMX4ALL
DMX4ALL DMX-Relais 2 INRUSH User manual
DMX4ALL
DMX4ALL DMX-Universal-Demux User manual
DMX4ALL
DMX4ALL WirelessDMX RX board User manual
DMX4ALL
DMX4ALL DMX-Player L User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
