DL diode led User manual
DRY LOCATION
1 OF 2 IG121815-3.0
®
12V
DC
INSTALLATION GUIDE
CLICKTIGHT®PRO
24V
DC
CLICKTIGHT
®
PRO INSTALLATION GUIDE
SAFETY & WARNINGS
SUPPLIED ACCESSORIES
TOOLS FOR INSTALL
INSTALLATION
1
PREPARE WIRE AND ATTACH SPADE CONNECTORS.
COMPATIBLE LED TAPE LIGHTS
CLICKTIGHT PRO is compable with most Diode LED solid color
2-channel 12V and 24V tape lights. See product page for a full list.
a. Determine wire gauge (22 - 18AWG). Strip wires.
MAIN POWER MUST BE TURNED
OFF BEFORE INSTALLATION.
12VDC 60W 5A
24VDC 100W 4.17A
DO NOT EXCEED CLASS 2 LIMIT
WHEN LOADING CLICKTIGHT.
CORRECT - CUT TAPE LIGHT SO
FOUR CONTACT/SOLDER POINTS
REMAIN TO ALLOW FOR GAP
BETWEEN PRONGS AND LED.
INCORRECT - DO NOT ALLOW
CLICKTIGHT PRONGS TO TOUCH
LED CHIP CONTACTS WHEN LED
TAPE IS INSERTED.
Tape-To-Wire Kit: DI-CKTP-TTW-10
A. CLICKTIGHT PRO Tape-To-Wire Connector (10)
B. Spade Connector - 22AWG - 18AWG (25)
C. Tape Light Fastener (10) & Screws (20)
D. Wire Fastener (10) & Nails (10)
• Small Phillips-head screwdriver
• Wire Stripper / Crimper
• Scissors
• Hammer
A. B. C.
D.
Tape-To-Tape Kit: DI-CKTP-TTT-5
A. CLICKTIGHT PRO Tape-To-Tape Connector (5)
B. Tape Light Fastener (10) & Screws (20)
A. B.
3/8 in.
(10 mm)
b. Aach spade connectors with crimper tool.
Fit in crimper tool
notch. Squeeze to
secure wire.
ATTACH WIRE TO CLICKTIGHT
2
FOR BLAZE LED TAPE LIGHT
! !
2 OF 2 IG121815-3.0
CLICKTIGHT
®
PRO INSTALLATION GUIDE
®
+
−
®
+
−
INSTALLATION CONT.
5
MOUNT TAPE LIGHT TO SURFACE.
ATTACH TAPE LIGHT TO CLICKTIGHT.
7
FASTEN WIRE TO SURFACE.
3
Place wire fastener around
wire and hammer into place.
CHOOSE OPTION (a) OR (b) FOR CUTTING
INSTRUCTIONS.
4
Cut at the line indicated with scissors icon.
®
+
−
1
2
®
+
−
®
+
−
®
+
−
Prep surface to remove dust and dirt. Adhere to a smooth,
nished, dry surface.
®
+
−
Ulize included Tape Light Fastener to secure tape to surface.
Fasten with small screwdriver.
DO NOT PLACE FASTENER ON LED CHIPS OR RESISTORS!
Determine orientaon of
tape light for correct polarity.
TEST CONNECTION.
6
Prior to mounng, turn on power and test connecon to
ensure system is operang properly. Turn o power again
before mounng.
ADD TAPE-TO-TAPE CONNECTORS AND/OR
BENDING EXTENSIONS.
8
®
®
®
−
+
®
+
−
TROUBLESHOOTING
Symptom Common Cause
Fixture does not
illuminate
• Incorrect wiring. Polarity of Low Voltage V+ and V- are
reversed. Check connecon at every CLICKTIGHT to
ensure polarity is not reversed.
• Circuit breaker is OFF or tripped.
• Incorrect voltage pairing of dimmer and xture. 12 V
dimmer models will not power a xture with a higher
voltage rang.
Fixture ickers
randomly, may
shut o
• Connecon is not secure. Check connecon at crimp,
at metal prongs of CLICKTIGHT and at any other
connecons.
Fixture will
not insert into
CLICKTIGHT
• If tape light does not t under CLICKTIGHT prongs due
to ghtness, gently slide a 1/8” at head screwdriver
under prongs (shown below). Once both prongs are
loosened, proceed to slide tape light under prongs.
TAPE-TO-TAPE
CONNECTOR
BENDING EXTENSION
(2x TAPE-TO-WIRE
CONNECTORS)
Insert strip under
metal contacts.
a
b
Applies to AVENUE 24™, FLUID VIEW®, VALENT®, VALENT®
HD, and ULTRA BLAZE™ tape lights.
Applies only to BLAZE™ tape light:
+
−
+
−
+
−
+
−
+
−
+
−
+
−
DO NOT cut at scissors icon. Instead, cut tape light along outside
edge of LED chip closest to scissors icon so four contact/solder
points remain intact to tape light.
®
+
−
1
2
®
+
−
®
+
−
®
+
−
Table of contents
Other DL Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
