*Lens is not included
CH 03101
Day & Night Box Camera
Diagram
Caution
1. Do not attempt to disassemble the camera.
In order to prevent electric shock, do not remove screws or cover.
2. Handle the camera with care.
The camera could be damaged by improper handling or storage
3. Do not expose the camera to rain or moisture, or try to operate in wet
areas.
Take immediate action if the camera becomes wet. Turn the power off and
request service to qualified personnel. Moisture can damage the camera and
also create a risk of electric shock.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. In case the dirt is hard to
remove, use a mild detergent and wipe gently.
5. Never point the camera toward the sun.
Whether the camera is used outdoor or not, never point it toward the sun. Use
with caution when operating the camera in the vicinity of spot lights or other
bright lights and light reflecting objects.
6. Do not operate the camera beyond its temperature, humidity, or power
source ratings.
Do not use the camera in an extreme environment where high temperature or
high humidity exists. Use the camera under conditions where temperatures are
between 14 F~122 F (-10 C~+50 C), and humidity is below 85%,
SA 1965
The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
To prevent electric shocks and risk of fire hazards,
DO NOT use other than specified power source.
CAUTION:
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
SA 1966
!
WARNING
CAUTION
This equipment has been tested and found to comply with the limits for a Class A. Digital
device. Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instruction manual, it may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at own expense.
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
oooo
104.9
POWER
ENTER
R
L
D
U
CLASS2 ONLY
Non polarity
DC 12V
VIDEO
63.9
55.5
Mounting hole
: 1/4"-20UNC(20Thread)
L-4.5mm±0.2mm
Hexagon wrench C mount ring
: 1.27mm L type
Accessories
Lens Connection
Manual iris lens
1. Before mounting a lens, please check whether it is a C or CS mount lens
2. CS mount lens : After removing the protective rubber, attach the lens
3. C mount lens : Before installing the lens, attach C mount ring to the camera
4. Set the lens mode to manual
Auto iris lens
1. Attach a DC lens like the manual lens connection
2. Connect the lens plug to the auto iris connection on the side of the camera
3. Set the lens mode to DC by OSD
POWER
ENTER
R
L
D
U
CLASS2 ONLY
Non polarity
DC 12V
VIDEO
Setup for Camera Function
1. Function setting combination
ENTER : Display the menu and function
LEFT : Move to left
RIGHT : Move to right
UP : Move to up
DOWN : Move to down
2. OSD Menu
ENTER button : Press 'ENTER' button to go to the menu
UP & DOWN button : Press 'UP' or 'DOWN' button to go up or down
LEFT & RIGHT button : Press 'LEFT' or "RIGHT' button to go left or right
NOTICE
' ' Signal means that you can go to the sub menu in case of pressing
"ENTER" button.
①
②
③
④
⑤
①
②
③
