Dish Network DISH 500 User manual
Installation Diagrams - Introduction to Installation Diagrams 3 - 1
Introduction to Installation Diagrams
•The installation options listed on the following pages may or may not be reimbursable installations. Refer to the latest
Business Rules to confirm reimbursement status.
•Installations must use all Legacy LNBFs and switches, or all DISH Pro/DISH Pro Plus LNBFs and switches. Do not mix
and match Legacy components with DISH Pro/DISH Pro Plus components.
•If upgrading from Legacy LNBFs and switches to DISH Pro/DISH Pro Plus LNBFs and switches, ensure all Legacy
components (for example, power inserters) are removed. Remove DP Adapters from any Legacy receivers connected
to DISH Pro Plus components.
•Maximum distance between the furthest LNBF and farthest receiver is 200 feet for DP/DP Plus receivers; 100 feet for
Legacy receivers (four-digit model numbers). Maximum cable length from a wing dish with a compatible DISH Pro
LNBF to a DISH Pro Plus LNBF’s LNB INport is 80 feet with 120 feet from DPP LNBF to receiver for a total of 200 feet.
•Ensure all components (for example, cable, ground blocks, diplexers, splitters, line amps, barrel connectors, wall plates
and surge protectors) are rated for DISH Pro/DISH Pro Plus installations (rated to 2150 MHz and pass DiSEqC 22 KHz
tone—review the DISH Network Approved Accessories List), also referred to as DP compatible.
•Refer to the LNBFs and Switches and Dish Antennas sections for Legacy receiver installation considerations.
Abbreviations
•DP: DISH Pro
•DPP or DP Plus: DISH Pro Plus
Installation Diagrams - Multiple Orbital Location Dish Options 3 - 2
Multiple Orbital Location Dish Options
LNBFs Switch Receivers/Tuners Supported Diagram
110º & 119º (2 Orbital Locations) (if needed) (without additional switches)
DISH 500
DP Plus Twin n/a 2 dual (w/ DPP Separators) or 2 single-tuners 1
DP Twin (or 2 DP Duals/Singles) DP34 Switch 2 dual or 4 single-tuners n/a
DP Twin (or 2 DP Duals/Singles) DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners 2
DP Twin n/a 1 dual or 2 single-tuners n/a
DP Quad n/a 2 dual or 4 single-tuners n/a
2 DP Duals/Singles 2 DP21 Switches 1 dual or 2 single-tuners n/a
DISH 500H 2 DP Low-Noise Duals DP34 Switch 2 dual or 4 single-tuners n/a
2 DP Low-Noise Duals DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners n/a
110º, 119º, and Wing Dish (3 Orbital Locations)
DISH 500 with Wing Dish*
DP Plus Twin and DP Dual/Single n/a 2 dual (w/ DPP Separators) or 2 single-tuners 3
DP Twin and DP Dual/Single DP34 Switch 2 dual or 4 single-tuners n/a
DP Twin and DP Dual/Single DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners 4
DP Twin and DP Dual/Single 2 DP21 Switches 1 dual or 2 single-tuners n/a
110º, 119º, & 129º (3 Orbital Locations)
DISH 1000 DP Plus Twin and DP Dual/Single n/a 2 dual (w/ DPP Separators) or 2 single-tuners 5
DP Twin and DP Dual (or 3 DP Duals/Singles) DP34 Switch 2 dual or 4 single-tuners n/a
DP Twin and DP Dual (or 3 DP Duals/Singles) DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners 6
DISH 1000.2 DP Plus 1000.2 LNBF n/a 3 dual (w/ DPP Separators) or 3 single-tuners 7
3 DP Duals/Singles and 1000.2 Three-LNBF Bracket DP34 Switch 2 dual or 4 single-tuners n/a
3 DP Duals/Singles and 1000.2 Three-LNBF Bracket DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners 8
110º, 119º, 129º, with Wing Dish (4 Orbital Locations)
DISH 1000 with Wing Dish* DP Twin with 2 DP Duals (or 4 DP Duals/Singles) DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners 9
DISH 1000.2 with Wing Dish*
DP Plus 1000.2 LNBF and DP Dual/Single n/a 3 dual (w/ DPP Separators) or 3 single-tuners 10
3 DP Duals/Singles, 1000.2 Three-LNBF Bracket,
& DP Dual/Single DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners 11
DP Plus 1000.2 LNBF and DP Dual/Single DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners n/a
* See Single Orbital Location Wing Dish Options. Wing dish must use a DP-compatible LNBF.
Installation Diagrams - Single Orbital Location Wing Dish Options 3 - 3
Single Orbital Location Wing Dish Options
LNBFs Switch Receivers/Tuners Supported Diagram
110º, 118.7º, & 119º (3 Orbital Locations) (if needed) (without additional switches)
DISH 500+ DP 500+ LNBF Assembly DP34 Switch 2 dual or 4 single-tuners n/a
DP 500+ LNBF Assembly DPP33 Switch 3 dual (w/ DPP Separators) or 3 single-tuners 12
110º, 118.7º, 119º, with Wing Dish (4 Orbital Locations)
DISH 500+ with Wing Dish* DP 500+ LNBF Assembly and DP Dual/Single DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners 13
110º, 118.7º, 119º, and 129º (4 Orbital Locations)
DISH 1000+ DP 500+ LNBF Assembly, 1000+ Bracket, & DP Dual/Single DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners 14
61.5º, 72.7º, and 77º (3 Orbital Locations)
1000.4 Assembly DP Plus1000.4 LNBF n/a 3 dual (w/ DPP Separators) or 3 single-tuners 15
DP Plus 1000.4 LNBF DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners 16
61.5º, 72.7º, 77º and 118.7° (4 Orbital Locations)
1000.4 Assembly DP Plus 1000.4 LNBF, DP 500+ LNBF Assembly DPP44 Switch 4 dual (w/ DPP Separators) or 4 single-tuners n/a
* See Single Orbital Location Wing Dish Options. Wing dish must use a DP-compatible LNBF.
LNBFs Diagram
DBS: 61.5º, 72.7º, 77º, 110º, 119º, 129º, or 148º
DISH 500 w/ I-Bracket, or other approved dish** Dual: DP or Legacy—must match other LNBFs/switches in installation 17
FSS: 105º or 121º
105 or 121 SuperDISH FSS LNBF (DP-compatible only) n/a
** May include 24” dish or larger, depending on location.
Installation Diagrams - Diagram 1. 110° & 119° (DISH 500) 3 - 4
Diagram 1. 110° & 119° (DISH 500)
Uses DISH Pro Plus Twin
Or Legacy Receiver
•Single-cable/dual-tuner receiver
installations require a DP Plus
Separator.
•Single Legacy receiver installations are
not supported.
•Installations with two Legacy receivers
cannot view the third orbital location.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 2. 110° & 119° (DISH 500) 3 - 5
Diagram 2. 110° & 119° (DISH 500)
Uses DISH Pro Twin and DISH Pro Plus 33
•A DP34 Switch is also an option if you
don’t require a single-cable/dual-tuner
installation. See the DP34 Switch for
connectivity details.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 3. 110° & 119° (DISH 500) with Wing Dish 3 - 6
Diagram 3. 110° & 119° (DISH 500) with Wing Dish
Uses DISH Pro Plus Twin and DISH Pro Dual or Single
Or Legacy Receiver
•Single-cable/dual-tuner receiver
installations require a DP Plus
Separator.
•Must have a DP or DPP receiver
connected for viewing three orbital
locations.
•Single Legacy receiver installations are
not supported; installations with two
Legacy receivers cannot view the third
orbital location.
•The LNBF used on the wing dish must
be DP compatible.
•Maximum cable length between the
wing dish and the DPP Twin’s LNB IN
port is 80 feet.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 4. 110° & 119° (DISH 500) with Wing Dish 3 - 7
Diagram 4. 110° & 119° (DISH 500) with Wing Dish
Uses DISH Pro Twin, DISH Pro Dual or Single, and DISH Pro Plus 33
•A DP34 Switch is also an option if you
don’t require a single-cable/dual-tuner
installation. See the DP34 Switch for
connectivity details.
•The LNBF used on the wing dish must
be DP compatible.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 5. 110°, 119°, & 129° (DISH 1000) 3 - 8
Diagram 5. 110°, 119°, & 129° (DISH 1000)
Uses DISH Pro Plus Twin and DISH Pro Dual or Single
Or Legacy Receiver
•Single-cable/dual-tuner receiver
installations require a DP Plus
Separator.
•Single Legacy receiver installations are
not supported.
•Installations with two Legacy receivers
cannot view 129°.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 6. 110°, 119°, & 129° (DISH 1000) 3 - 9
Diagram 6. 110°, 119°, & 129° (DISH 1000)
Uses DISH Pro Twin, DISH Pro Dual, and DISH Pro Plus 33
•A DP34 Switch is also an option if you
don’t require a single-cable/dual-tuner
installation. See the DP34 Switch for
connectivity details.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Installation Diagrams - Diagram 7. 110°, 119°, & 129° (DISH 1000.2) 3 - 10
Diagram 7. 110°, 119°, & 129° (DISH 1000.2)
Uses DP Plus 1000.2 LNBF
Or Legacy Receiver
•Single-cable/dual-tuner receiver
installations require a DP Plus Separator.
•A Legacy receiver installation must also
include at least one DP or DP Plus
receiver.
•Grounding according to the National
Electric Code (NEC) and all local
electrical codes is required.
Other manuals for DISH 500
1
This manual suits for next models
4
Other Dish Network Antenna manuals
Dish Network
Dish Network DISH 1000.2 User manual
Dish Network
Dish Network SuperDISH User manual
Dish Network
Dish Network DishPro User manual
Dish Network
Dish Network DISH 500 User manual
Dish Network
Dish Network DishPro User manual
Dish Network
Dish Network Tailgater User manual
Dish Network
Dish Network DISH 1000 User manual
Dish Network
Dish Network Playmaker User manual
Dish Network
Dish Network D1000.4 EA User manual
Dish Network
Dish Network Tailgater User manual
Popular Antenna manuals by other brands
Alfa Network
Alfa Network APA-L01 Specifications
Naval
Naval PR-422CA Operation manual
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series manual
TERK Technologies
TERK Technologies TV44 owner's manual
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK quick start guide
HP
HP J8999A instructions
CommScope
CommScope CMAX-OMFX-43M-I53 Installation instruction
Ramsey Electronics
Ramsey Electronics DAP25 Kit assembly and instruction manual
COBHAM
COBHAM SAILOR 800 VSAT Replacement procedure
Trango Systems
Trango Systems AD900-9 Specification sheet
Steren
Steren ANT-100 user manual
Proxim
Proxim 5054-PA-23 quick start guide