Discovery Telecom ESIM002 User manual
ESIM022
GSM DIALLER
Тел: +7 495 7907870
Моб: +7 965 4429948
Skype: Discoverytelecom
Mail: [email protected]
www.discoverytelecom.ru
2
2EN ESIM022 User manual v1.1
User Manual v1.1
SAFETY INSTRUCTIONS
Please read and follow these safety guidelines to safeguard yourself and others:
• GSM dialler ESIM022 (later referred to as “the system” or “the device”) contains a built-in
radio transceiver operating in GSM 900/1800 MHz bands.
• DO NOT use the system where it can cause potential danger and interfere with other
devices – such as medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impact.
• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully
qualied personnel only.
Please, use the 12-15 V 300 mA DC power supply unit that meets the EN
60950-1 standard. Any additional device you connect to the system, such as a
computer, must also be powered by an EN 60950-1 approved supply. When con-
necting the power supply to the system, mind the polarity terminals. DO NOT
switch the polarity terminals places.
External power supply must be reachable
and can be connected to AC mains only
inside installation room with automatic
2-pole circuit breaker capable of discon-
necting circuit in the event of short circuit or
over-current condition. Open circuit breaker
must have a gap between connections of
more than 3 mm and the disconnection cur-
rent 5 A.
Phase
DC 12-15 V
Null
PE
ESIM022
USB cable
Disconnect the mains power before installing. Never install or carry out mainte-
nance during stormy weather. The electric socket that powers the system must be
easily accessible. In case of power cut, the system is powered by a back-up battery
(if any).
WARNING: Only use the approved 8.4V 250mAh rechargeable Ni-Mh 6HR61
(IEC)/7.2H5 (ANSI/NEDA) back-up battery with the system to avoid re or explo-
sion. Take care when connecting positive and negative battery terminals.
3
3
ESIM022 User manual v1.1
To switch the system o, unplug the external electric power supply, disconnect
the back-up battery or any other linked device that the system is powered from. A
blown fuse cannot be replaced by the user. The replacement fuse has to be of the
kind indicated by the manufacturer (Fuse F1 model – miniSMDC 0,5A).
If you use a computer for the device conguration, it must earthed.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see right) or its
documentation indicates that the product must not be disposed of together with household waste. To
prevent possible harm to human health and/or the environment, the product must be disposed on in
an approved and environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the system supplier, or the local authority responsible for waste disposal
in your area.
4
4EN ESIM022 User manual v1.1
Contents
1. GENERAL INFORMATION .............................................................................................. 7
2. TECHNICAL SPECIFICATIONS ....................................................................................... 8
2.1. Electrical & Mechanical Characteristics .................................................................................... 8
2.2. Wiring Diagrams.......................................................................................................................... 10
3. INSTALLATION ............................................................................................................ 11
4. GENERAL OPERATION DESCRIPTION......................................................................... 13
5. CONFIGURATION METHODS ....................................................................................... 14
5.1. SMS Text Messages .................................................................................................................... 14
5.2. ELDES Conguration Tool.......................................................................................................... 14
6. USER PHONE NUMBERS ............................................................................................. 14
7. DATE AND TIME ........................................................................................................... 16
8. INPUTS ........................................................................................................................ 17
8.1. Input Z1 .........................................................................................................................................17
8.2. Input Z2 ........................................................................................................................................ 18
9. TAMPER ....................................................................................................................... 24
10.ALARM/RESTORE NOTIFICATIONS............................................................................ 25
11.OUTPUT ....................................................................................................................... 31
11.1. Output Name ............................................................................................................................... 31
11.2. Turning Output ON and OFF...................................................................................................... 32
12.BACKUP BATTERY AND MAINS POWER SUPPLY STATUS MONITORING ................ 33
13.SYSTEM INFORMATION. STATUS SMS ....................................................................... 37
13.1. Periodic Status SMS.................................................................................................................... 38
14.SYSTEM NOTIFICATIONS ............................................................................................ 39
15.ONBOARD TEMPERATURE SENSOR..........................................................................43
16.REMOTE LISTENING....................................................................................................44
17.TECHNICAL SUPPORT .................................................................................................46
17.1. Troubleshooting......................................................................................................................... 46
17.2. Restoring Default Parameters ................................................................................................46
17.3.Updating the Firmware via USB Cable..................................................................................... 47
18.RELATED PRODUCTS ..................................................................................................48
5
5
ESIM022 User manual v1.1
Тел: +7 495 7907870
Моб: +7 965 4429948
Skype: Discoverytelecom
Mail: [email protected]
www.discoverytelecom.ru
6
6EN ESIM022 User manual v1.1
Limited Liability
The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but
that it does not guarantee against the occurrence of such events.
“ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue
whilst using the system. The liability of “ELDES UAB” is limited to the value of the system
purchased.
“ELDES UAB” is not aliated with any mobile/wireless/cellular provider and is therefore not
responsible for the quality of such services.
Manufacturer Warranty
The system carries a 24-month manufacturer warranty from “ELDES UAB”.
The warranty begins the day the system is purchased by the user and the receipt must be retai-
ned as proof of purchase date. The warranty remains valid only if the system is used as intended,
following all guidelines outlined in this manual and in accordance with the operating conditions
specied.
The warranty is void if the system has been exposed to mechanical impact, chemicals, high
humidity, uids, corrosive and hazardous environments or force majeure factors.
Dear Customer,
Thank you for choosing to purchase the GSM dialler ESIM022. Your thoughtful decision will
ensure reliable solution for many years as all ELDES products are manufactured to meet
the highest standards.
We are condent that you will be completely satised with your product. However, in the
unlikely event that you do experience a problem, please contact the dealer from whom
you made your purchase.
Contents of Pack
Item Quantity
1. ESIM022 ...............................................................1
2. User manual.........................................................1
Not included:
• SIM card – we recommend you get a contract SIM, not Pay As You Go.
• Back-up battery - can be obtained from your local distributor.
• miniUSB cable - can be obtained from your local distributor.
• Temperature sensor - can be obtained from your local distributor.
• Microphone - can be obtained from your local distributor
7
7
ESIM022 User manual v1.1
1. GENERAL INFORMATION
ESIM022 is a micro-controller based device intended to receive alarm/restore events by SMS text
message or phone call and control an electrical appliance via the GSM network.
Examples of using the system:
• Notication of system events, such as arming/disarming, alarm/restore from non-GSM alarm
system.
• Non-GSM alarm system arming/disarming by SMS text message.
• Any electrical appliance control: lighting, watering, heating etc.
• Remote reboot of the “frozen” systems, such as computer network or a server.
• Notication of failure or restoration of an electronic device by SMS text message or phone call.
Main features:
• Conguration by SMS text message and PC.
• Up to 2 users for system conguration, control and acceptance of system event notications
by SMS text messages or phone calls.
• 2 inputs customizable as NC or NO.
• Input Z1 mode: digital.
• Input Z2 modes: digital or temperature sensor for 1 external temperature sensor connection.
• 1 open-collector output for electrical appliance control or non-GSM alarm system arming/
disarming (keyswitch).
• Tamper switch for system sabotage detection.
• Optional back-up battery to maintain the power for up to 12 hours and notify the user
regarding mains power loss and restore.
• Periodic self-test notication by SMS text message to user phone number.
• Customizable notication texts.
8
8EN ESIM022 User manual v1.1
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Supply voltage.....................................................12-15 V 300 mA max
Average current used in idle state ................... 16 mA
Supported back-up battery (optional) ............8.4V 250mAh rechargeable Ni-Mh 6HR61
(IEC)/7.2H5 (ANSI/NEDA)
GSM modem frequency......................................900/1800 MHz
Number of outputs .............................................1
Output circuit.......................................................Open collector output.
Output is pulled to COM when
turned ON.
Maximum commuting output values...............30 V 200 mA
Number of inputs................................................2
Supported temperature sensor model............Maxim®/Dallas® DS18S20, DS18B20
PCB dimensions...................................................71x50x27 mm
Enclosure dimensions ........................................96x59x34 mm
Operating temperature range...........................-30…+55 °C (-35...+55 °C with limitations)
Humidity ...............................................................0-90% RH @ 0... +40 °C (non-condensing)
2.2. Main Unit, LED Indicator & Connector Functionality
Front Back
C1
Z2
DCCOM
COM
SIM CARD
TAMPER
RESET
MIC
LED
ANT
USB
Z1
OPEN
G S M
MO DE M
FW
+
BATTERY
-
F1
1 2
9
9
ESIM022 User manual v1.1
Main Unit Functionality
ANT GSM antenna
FW Pins for rmware update
TAMPER Tamper switch
GSM MODEM GSM network 900/1800 MHz modem
RESET Button for restoring default settings
SIM CARD SIM card slot / holder
LED Light-emitting diode indicating system status
USB Mini USB port
MIC Microphone connector
-/+ Backup battery slots
F1 0.5A fuse
LED indication Description
OFF No power supply
Flashing every 30 ms SIM card is not present / PIN code enabled
Flashing every 0,5 sec. Searching for GSM network
Flashing every 1 sec. Connected to GSM network/system operating successfully
Connerctors Description
Z1 Digital input terminal
COM Common terminal
Z2 Digital input terminal/temperature sensor data terminal (DATA)
DC Positive power supply terminal
C1 Open-collector output terminal/temperature sensor power
supply terminal (+4V)
10
10 EN ESIM022 User manual v1.1
2.2. Wiring Diagrams
General wiring Temperature sensor wiring
ESIM022
Alarm system or other appliance
+12V
PGM2
PGM1
Z1 Z2 COMCOM DC C1
ESIM022
DS18S20, DS18B20
Temperature sensor
COMZ1 Z2 DC C1COM
GND
GND
DATA
DATA
+4V
+4V
Output wiring
ESIM022
Alarm system or other appliance
+12 V
+
Electrical
appliance
+
COMZ1 Z2 DC C1COM
3 4
5
Table of contents
