Directive Systems & Engineering DSE1245LYK User manual

DSE1245LYK Rev 3/21

Directive Systems & Engineering

2702 Rodgers Terrace

Haymarket, VA 20169-1628

www.directivesystems.com

703-754-3876

12cm Loop Yagi Kit, Model DSE1245LYK

SPECIFICATIONS

Frequency range: 2.35 to 2.45 GHz Gain: 20 dBi

Number of elements: 45 3 dB Beamwidth

Boom length: 80 inches (E plane): 16º

Boom diameter: 0.5” inches F/B ratio: >20 dB

Mast diameter: 1 1/2 in. max Maximum Power: 400 W average

Weight: (assembled) 3 pounds Stacking distance: 13 inches’ vertical

Connector: Type-N female 15 inches’ horizontal

PARTS LIST

Note: All hardware is Stainless Steel unless otherwise noted.

Anti-Seize Compound - Apply a small amount of the supplied Anti-Seize Compound to the aluminum

joints and to the threads of the U-Bolts to prevent galling.

BEFORE INSTALLING YOUR NEW ANTENNA, PLEASE BE SURE

TO READ THE ENCLOSED WARNING PAMPHLET.

CAUTION: While we strive to remove all burrs from all machined parts, there is always the possibility of

sharp edges. We strongly suggest checking the edges and use a fine file, or 400 grit sandpaper,

to remove any burrs that may have been left.

Quantity Description Quantity Description

2 0.5" Drilled boom 45 4-40 x 3/4" Machine screw

2 Reflector 1 & 2 45 4-40 Lock nut

1 Driven element 2 8-32 x 1/2" Machine screw

12 Directors 1-12 2 8-32 x 1" Machine screw

5 Directors 13-17 4 8-32 Hex Nut

6 Directors 18-23 4 8-32 Split lock washer

12 Directors 24-35 1 Boom-to-mast "L" bracket

7Directors 36-42 1 Boom-to-mast plate

1 Anti-Seize Compound 1 U-bolt with nuts & lock washers

2 1/2" Black End Cap 1 Saddle

1 Cable assy w/connector

1 Assembly Manual

P a g e | 2

DSE1245LYK Rev 3/21

(Can be up or down) (Can be left or right)

ASSEMBLY INSTRUCTIONS

1) Unpack the antenna and locate the hardware package. Antenna booms are shipped in

two sections. Use the alignment marks on the boom to correctly connect the boom pieces.

2) Attach loops to the boom with 4-40 x 3/4" screws, lock washers and nuts in proper

sequence. Loops go on the side of the boom marked with an "X". Attach the contents of each

bag of elements before opening the next bag. This will prevent any mix-up of elements on the

boom. When tightening the nuts on the parasitic elements, be careful not to torque them too

tightly. Snug down the nuts, align the elements and use a screwdriver for the final tightening. A

1/4" nut driver is almost mandatory for this job! Attach the driven element with the 1/4-20

stainless steel nut. If only a single antenna is being built, it doesn't matter which way the loop

is oriented. If antennas are to be stacked, see "Instructions for Stacking Loop Yagis".

3) Attach the boom-to-mast angle bracket and 8-32 x 1" hardware on the boom.

4) Attach the boom-to-mast plate to the angle bracket with the 8-32 x 1/2” screws, lock

washers and nuts. Install U-bolt so that the mast is directly under the boom.

5) Install the cable assembly through the hole in the driven element mounting bolt. Make

sure the connector bracket is correctly oriented, the bend should be forward for center mount

antennas and rear facing for rear mount antennas. Solder the outer shield to the driven loop

first making sure there is no shield sticking above the large hole in the driven loop. After the

shield is soldered, pass the center conductor through the small hole in the driven loop and

bend the center conductor over and solder (See Assembly Tips below).

We have created a You Tube video, the link of which can be found on our website,

documenting the following steps:

https://youtu.be/ojXbsDv5cvU

At this point the connector assembly is facing down, connect a piece of coax and your

SWR bridge or VNA. Pull down on the connector (which will flatten the loop) until you reach

the lowest SWR. If it’s less than 1.5:1 you can stop and make sure the loop doesn’t try to pop

back up, sometimes you have to squeeze the loop with your fingers to make sure it stays in

the shape that gave the best SWR. If you want to further lower the SWR, from the rear of the

P a g e | 3

DSE1245LYK Rev 3/21

antenna, place both your thumbs on the driven loop on either side and gently push it forward

towards D1, you only need to tilt it maybe 3/16” to ¼” and that should drop the SWR to 1.1:1

or less.

Now, GENTLY bend the UT-141 coax after it exits the boom towards the front or rear,

depending on the mounting. You do not want to bend it so tightly that it crushes where it

extends through the bolt. The connector bracket should line up with either D1 or D2 (or the

hole with the circle around it on rear mount antennas), remove that nut and place the

connector bracket on the screw and re-attach the nut. If the bracket doesn’t line up,

sometimes you have to flip the bracket. Loosen the ¾” nut by holding the connector body with

a 9/16” open end wrench. Remove the connector bracket and flip it.

Connector doesn’t fit Front Mount Connector Rear Mount Connector

6) Attach the feedline and tape it to the mast. Seal all connections with silicone RTV or

equivalent.

7) Attach the two black end caps, and this will complete the assembly of your

DSE1345LYK.

8) The SWR should be 1.5:1 or better. Additional tweaking can be accomplished by

adjusting the distance between the driven element and R1 or by adjusting the shape of the

driven element.

DO NOT, UNDER ANY CIRCUMSTANCES, APPLY ANY TYPE OF SEALANT OR COATING TO THE

DRIVEN ELEMENT, T-ARMS OR CONNECTOR ASSEMBLY, OTHER THAN KRYLON®

CLEAR COAT. ANY OTHER COATING WILL ADVERSELY AFFECT THE SWR AND VOID YOUR

WARRANTY.

P a g e | 4

DSE1245LYK Rev 3/21

ASSEMBLY TIPS:

The boom diameter is 0.5 inch, and it is drilled for 4-40 hardware (no. 33 drill bit). The driven

element hole is enlarged to 1/4 inch. All elements are 0.032-inch-thick and 0.250 inch wide.

Note that the element spacing from D7 on is 2.0025 inches. To bend elements, wrap the strip

around a suitable form (such as a piece of pipe or tubing). The driven element is formed in the

same way then soldered to the mounting bolt as shown. The feed coaxial cable (0.141-inch

semi rigid) goes through the mounting bolt and is soldered to the open ends of the element.

For best match, the driven element should be approximately 1.375 inches high; this makes it

wider than it is tall. This shape can be adjusted for best match. This antenna is based on work

done by G3JVL.

Soldered Driven Element

Directive Systems Warranty Policy

All Directive Systems antennas are built with the finest materials available. We take great pride

in building a quality product that will give years of good service and performance. . If there is a

defect in materials or workmanship within 90 days of purchase, Directive Systems will repair or

replace the defective part, free of charge, to the original purchaser. DO NOT RETURN ANYTHING

WITHOUT PRIOR AUTHORIZATION FROM DIRECTIVE SYSTEMS. Please contact us either by

phone or email describing the problem and we will work to resolve it.

If, after examining a new antenna you received, you are not satisfied, contact us immediately

for return authorization and refund. ANY ANTENNA THAT HAS BEEN MODIFIED WILL BE

SUBJECT TO A RESTOCKING CHARGE. IF AN ANTENNA IS SO MODIFIED AS TO MAKE IT

UNUSABLE, DIRECTIVE SYSTEMS RESERVES THE RIGHT TO REFUSE TO ACCEPT THE

ANTENNA FOR RETURN.

P a g e | 5

DSE1245LYK Rev 3/21

Note: All dimensions are in inches

Table of contents

Other Directive Systems & Engineering Antenna manuals

Directive Systems & Engineering

Directive Systems & Engineering DSE3318LYRMK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE3333LY User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2455LY User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE1327LYRM User manual

Directive Systems & Engineering

Directive Systems & Engineering DS 88-8 User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2425LYK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE1445LYA User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2424LYRM User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2414LYRMK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE3319LYK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE3319LYAK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2045LY User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2345LY User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2325LYK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE1345LY User manual

Directive Systems & Engineering

Directive Systems & Engineering Yagi DSE3319LYCEL User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2314LYRMK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE945LYRMK User manual

Directive Systems & Engineering

Directive Systems & Engineering DSEFO222-22 User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2414LYRM User manual

Directive Systems & Engineering

Directive Systems & Engineering DSE1276LY User manual

Directive Systems & Engineering

Directive Systems & Engineering DSEFO222-16 User manual

Directive Systems & Engineering

Directive Systems & Engineering DSEFO144-12 User manual

Directive Systems & Engineering

Directive Systems & Engineering DSEDBFEED User manual

Popular Antenna manuals by other brands

Alfa Network

Alfa Network APA-L01 Specifications

Naval

Naval PR-422CA Operation manual

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series manual

TERK Technologies

TERK Technologies TV44 owner's manual

HP J8999A instructions

MobilSat

MobilSat MSP-S Mounting instructions

Steren

Steren ANT-UHF 13 instruction manual

Novatel

Novatel 600-G User information

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna owner's manual

TRENDnet

TRENDnet TEW-AO12O Specifications

Radio Shack

Radio Shack 15-1837 owner's manual

CommScope

CommScope CMAX-OMFX-43M-I53 Installation instruction

Ramsey Electronics

Ramsey Electronics DAP25 Kit assembly and instruction manual

COBHAM

COBHAM SAILOR 800 VSAT Replacement procedure

Trango Systems

Trango Systems AD900-9 Specification sheet

Steren

Steren ANT-100 user manual

Proxim

Proxim 5054-PA-23 quick start guide

IWCS

IWCS iriBelt II Quick start user guide