DirectConnect DC-S-24M User manual
24-Port Gigabit Ethernet
Unmanaged Switch
DC-S-24M
Sku: 45123
User Manual
Version 1.0
Updated 10/29/2021
Copyright Statement
Our company reserves all copyrights of this document.Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this
document, in any form or by any means, without the prior written consent of our company is prohibited.
Exemption Statement
This document is provided "as is". The contents of this document are subject to change without any
notice. Please obtain the latest information through our company website. Our company endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.
Table of Content
1 Product Introduction................................................................................................................................ 1
1.1 DC-S-24M.....................................................................................Error! Bookmark not defined.
2 Installing and Connecting the Switch...................................................................................................... 5
2.1 Installation..................................................................................................................................... 5
2.1.1 Desktop Installation ............................................................................................................ 5
2.1.2 Rack-mountable Installation in 19-inch Cabinet................................................................. 5
2.1.3 Power on the Switch........................................................................................................... 6
2.2 Connect Computer (NIC) to the Switch........................................Error! Bookmark not defined.
24-Port Gigabit Ethernet Unmanaged Switch
1
1 Product Introduction
Thank you for choosing DirectConnect TM Networking!
DC-S-24M provides the seamless network connection. This device integrates 1000Mbps Gigabit
Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible
package. The Switch is a high performance upgrade to a 1000Mbps Gigabit network. Based on
Gigabit Ethernet Technology. It requires no configuration and is easy to use!
DC-S-24M
Model Name
10/100/1000Mbps Adaptive Ethernet port
DC-S-24M
24
DC-S-24M
Specification Parameter
Model Name
DC-S-24M
Interfaces
24*10/100/1000Mbps Adaptive Ethernet port
Power Supply
AC (AC) Input:
Rated voltage range: 100-240V~
Maximum voltage range: 90-264V~
Frequency: 50 -60 hz
Rated current: 0.5A
PoE
Nonsupport
Power Consumption
16W(Max)
Operating Temperature
0ºC ~ 40ºC
Storage Temperature
-40ºC ~ 70ºC
Operating Humidity
10% ~ 90% RH
Storage humidity
5% ~ 90% RH
Fan
No fan
24-Port Gigabit Ethernet Unmanaged Switch
2
EMI
GB9254-2008 Class A
Dimensions ( W x D x
H )
280*126*44mm
Switching Capacity
48Gbps
Hardware Version
V1.0
External Component Description
The front panel of the Route consists of 24*10/100/1000Mbps Adaptive Ethernet port, a series of LED indicators. The
rear panel provides a AC power connector, a Ground Terminal. Its appearance is shown below:
Figure 1-1 DC-S-24M Product appearance drawing
Figure 1-1
Front Panel
Figure 1-2 DC-S-24M Front Panel Diagram
Figure 1-2
【Annotation】
1.PWR indicator
2.10/100/1000Base-T Link/Act indicator
3.10/100/1000Base-T Adaptive Ethernet port
24-Port Gigabit Ethernet Unmanaged Switch
3
Rear Panel
Figure 1-3 DC-S-24M Rear Panel Diagram
Figure 1-3
【Annotation】
1.Ground Terminal
2.AC power connector
Power Supply
DC-S-24M Switch power supply adopts direct current(AC) input：
Rated voltage range: 100-240V~
Frequency: 50 to 60 Hz
Rated current: 0.5A
Power cord requirement: 10A power cord
Cooling Solution
DC-S-24M adopts a fanless design. To ensure good hear dissipation, when placing the chassis, a space of 10cm should
be reserved on both sides of the chassis and the rear panel to facilitate air circulation. Avoid blocking the openings the
chassis, otherwise the heat dissipation effect may be affected.
Indicator
Indicator
Face plate
Marker
Status
Indication
PWR Status Light
PWR
Off
Power Off.
Solid green
Power On.
Ethernet port indicator
1~24
Off
The port is NOT connected.
Solid orange
The port is connected at 10/100Mbps.
Blinking
The port 10/100M data transceiver.
24-Port Gigabit Ethernet Unmanaged Switch
4
Solid green
The port is connected at 1000Mbps.
Blinking
The port 1000M data transceiver.
24-Port Gigabit Ethernet Unmanaged Switch
5
2 Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please read the following topics and
perform the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage labeled on the Switch.
To keep the Switch free from shorts, do not open the Switch's shell even in power failure.
Make sure that there is proper heat dissipation from and adequate ventilation around the Switch.
Make sure the cabinet’s weight capacity is enough for the weight of the Switch and its accessories.
2.1.1 Desktop Installation
When installing the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the device and the
objects around it.
2.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed in a wiring closet with other
equipment. To install the Switch, please follow these steps:
a. Attach the mounting brackets on the Switch's side panels (one on each side) and secure them with the screws
provided.
Figure 2-1 - Bracket Installation
b. Use the screws provided with the equipment rack to mount the Switch on the rack and tighten it.
24-Port Gigabit Ethernet Unmanaged Switch
6
Figure 2-2 - Rack Installation
2.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power supply. Please follow the next
tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or multifunctional computer professional
receptacle. Please make sure to connect the metal ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle with the included power cord,
and check the power indicator is ON or not. When it is ON, it indicates the power connection is OK.
This manual suits for next models
1
Table of contents
Other DirectConnect Switch manuals
