Dimplex DS5629 User manual

Service Manual

Model Number

DS5629

UL Part Number

6900471359

7400490000R02

In keeping with our policy of continuous product development, we reserve the right to make changes without notice.

Dimplex North America Limited

1367 Industrial Road Cambridge ON Canada N1R 7G8

1-888-346-7539 www.dimplex.com

REV PCN DATE

01 - 9-Sep-11

02 13147 16-Apr-12

IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to service

this stove. For your safety, always comply with all warnings and safety instructions contained in this

manual to prevent personal injury or property damage.

2 www.dimplex.com

Always use a qualied technician or service agency to repair this stove.

!NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the

equipment.

WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the

risk of re, serious injury, or death.

OPERATION .........................................................3

MAINTENANCE......................................................4

EXPLODEDPARTSDIAGRAM..........................................5

WIRING DIAGRAM....................................................6

LIGHTBULBREPLACEMENT ..........................................7

UPPER LIGHT BULB REPLACEMENT.......................................................7

LOWERLIGHTBULBREPLACEMENT......................................................7

FLAME ROD REPLACEMENT...........................................7

FLICKERMOTORREPLACEMENT ......................................8

REMOTE CONTROL RECEIVER REPLACEMENT...........................8

CONTROLSREPLACEMENT...........................................8

SWITCHES.............................................................................9

THERMOSTAT ..........................................................................9

POWER CORD REPLACEMENT.........................................9

HEATER ASSEMBLY REPLACEMENT ...................................10

TROUBLESHOOTINGGUIDE..........................................11

TABLE OF CONTENTS

Remote Control

The stove is supplied with a radio frequency remote control.

This remote control has a range of approximately 50 feet

(15.25 m), it does not have to be pointed at the stove and

can pass through most obstacles (including walls). It is

supplied with one of hundreds of independent frequencies

to prevent interference with other units.

!NOTE: Before attempting any operation with the

remote, pull the plastic insulator strip out from between

the remote casing and battery cover (Figure 2).

Remote Operation

The stove is supplied with an integrated on/off remote

control

!NOTE: Ensure that the stove 3-Position Switch is set to

the remote control setting.

To operate, push the ON button to turn stove on, push the

OFF button to turn the stove off.

Remote Control Initialization/Reprogramming

If the remote control or remote control receiver has been

replaced, follow these steps to initialize the remote control

and receiver:

Set the 3-Position Switch to OFF.1.

Wait a minimum of ve (5) seconds and set the 3 2.

Position Switch to the “=” position (Figure 1A).

Within3. 10 seconds of re-acquiring power, press the ON

button located on the remote control.

!NOTE: You will have only 10 seconds to perform this

last step. Failure to do so will result in these steps needing

to be followed again.

This will synchronize the remote control and receiver.

Battery Replacement

To replace the battery:

Slide battery cover open on the remote control1.

(Figure 2).

Install one (1) 12-Volt (A23) battery in the battery2.

holder.

Close the battery cover3.

Battery must be recycled or disposed of properly.

Check with your Local Authority or Retailer for

recycling advice in your area.

OPERATION

To access the controls go to the back of the Stove. (Figure

A. 3-Position Switch

The switch has two ON positions marked with “-“ and “=”.

The “-“ position is for manual operation. In this position the

built-in remote control is bypassed. The “=” position is for

operating the unit with the provided remote control. When

in “=” position the unit is operated with the ON and OFF

buttons of the remote control.

When the switch is in the center position the unit is off.

B. Heater On/Off Switch

The Heater On/Off Switch supplies power to the heater fan

and the heater element.

C. Heater Thermostat Control

To adjust the temperature to your individual requirements,

turn the thermostat control clockwise all the way to turn on

the heater. When the room reached the desired tempera-

ture, turn the thermostat knob counter clockwise until you

hear a click. Leave in this position to maintain the room

temperature at this setting. For additional heat, turn clock-

wise until you hear the click again and the heater will turn

on. To turn the heater off, switch the Heater On/Off switch

to the OFF position.

!NOTE: When the heater is switched ON, the heater fan

will operate. The heater element may or may not be on,

depending on the thermostat control setting (See “Heater

Thermostat Control”)

Resetting the Temperature Cutoff Switch

Should the heater overheat, an automatic cut out will turn

the heater off and it will not come back on without being

reset. It can be reset by switching the 3-Position Switch to

OFF and waiting 5 minutes before switching the unit back

on.

CAUTION: If you need to continuously reset the

heater, unplug the unit and call Dimplex North America

Limited at 1-800-668-6663.

Figure 2

Off Button

Button

Battery

Cover

Plastic

Strip

Figure 1

4 www.dimplex.com

MAINTENANCE

WARNING: Disconnect power before attempting any

maintenance or cleaning to reduce the risk of re,

electric shock or damage to persons.

Light Bulb Replacement

Allow at least 5 minutes for light bulbs to cool off before

touching bulbs to avoid accidental burning of skin.

Light bulbs need to be replaced when you notice a dark

section of the ame or when the clarity and detail of the log

exterior disappears. There are two bulbs under the log set

which generate the ames and embers.

Tool Requirements

Phillips screw driver

Helpful Hints

It is a good idea to replace all light bulbs at one time if they

are close to the end of their rated life. Group replacement

will reduce the number of times you need to open the unit

to replace light bulbs.

Upper Light Bulb Requirements

Quantity of 1 clear chandelier or candelabra bulbs with an

E-12 (small) socket base, 7 watt rating.

Upper Bulb Replacement

Open door by pulling the handle.1.

Locate the upper bulb bracket.2.

Bend light retainer bracket down.3.

Locate and remove the light bulb.4.

Insert new bulb.5.

Bend light retainer bracket back into its original posi-6.

tion.

Close the door.7.

Lower Light Bulb Requirements

Quantity of 2 clear chandelier or candelabra bulbs with an

E-12 (small) socket base, 60 watt rating.

Lower Bulb Replacement

Open door by pulling the handle.1.

Remove the screw from the logset located in the center2.

of the emberbed and remove the logset from the unit.

Locate and examine the bulbs to determine which3.

bulb(s) required replacement.

Locate and remove the light bulb(s).4.

Insert new bulb(s).5.

Install the logset into the unit, pushing rmly against 6.

the glass. Replace the logset retaining screw into the

ember bed.

Close the door.7.

Glass Cleaning

The clear door is cleaned in the factory during the as-

sembly operation. During shipment, installation, handling,

etc., the clear door may collect dust particles, these can be

removed by dusting lightly with a clean dry cloth.

To remove ngerprints or other marks, the clear door can

be cleaned with a damp cloth. The clear door should be

completely dried with a lint free cloth to prevent water

spots. To prevent scratching, do not use abrasive cleaners

or spray liquids on the clear door surface.

Plastic Door Cleaning

To remove ngerprints or other marks, the clear door can

be cleaned with a damp cloth. The clear door should be

completely dried with a lint free cloth to prevent water

spots. To prevent scratching, do not use abrasive cleaners

or spray liquids on the clear door surface.

Stove Surface Cleaning

Use warm water only to clean painted surfaces of the Com-

pact Stove. Do not use abrasive cleaners.

Servicing

Except for light bulb replacement and cleaning described

above, an authorized service representative should perform

any other servicing.

EXPLODED PARTS DIAGRAM

Cutout1. . . . . . . . . . . . . . . . . . . . . . . . . . . 2300270100RP

Flicker Motor2. . . . . . . . . . . . . . . . . . . . . . 2000210200RP

Heater/Blower Assembly3. . . . . . . . . . . . . 2200490700RP

Thermostat4. . . . . . . . . . . . . . . . . . . . . . 2300150100RP*

3 Position Switch5. . . . . . . . . . . . . . . . . . . 2800071100RP

Heater On/Off Switch6. . . . . . . . . . . . . . . 2800070200RP

Flame Rod7. . . . . . . . . . . . . . . . . . . . . . . 5900080600RP

Strain Relief Bushing8. . . . . . . . . . . . . . . 8500000400RP

Log Set9. . . . . . . . . . . . . . . . . . . . . . . . . . 0438780100RP

Upper Lampholder10. . . . . . . . . . . . . . . . . 4200121000RP

Lower Lampholder Set11. . . . . . . . . . . . . . 2500510000RP

Power Cord12. . . . . . . . . . . . . . . . . . . . . . . 4100040900RP

Terminal Block13. . . . . . . . . . . . . . . . . . . . . 4000070100RP

Capacitor14. . . . . . . . . . . . . . . . . . . . . . . . . 2300030100RP

Partially Reective Glass15. . . . . . . . . . . . 5900630100RP

Front Glass16. . . . . . . . . . . . . . . . . . . . . . . 5900670100RP

Control Knob17. . . . . . . . . . . . . . . . . . . . . . 8800000300RP

Door - Bronze18. . . . . . . . . . . . . . . . . . . . .043874040MRP

Gloss Black . . . . . . . . . . . . . . . . 0438740304RP

Pewter . . . . . . . . . . . . . . . . . . . . 043874050NRP

Cranberry . . . . . . . . . . . . . . . . . 0438740203RP

Foot - Bronze19. . . . . . . . . . . . . . . . . . . . .043873040MRP

Gloss Black . . . . . . . . . . . . . . . . 0438730304RP

Pewter . . . . . . . . . . . . . . . . . . . . 043873050NRP

Cranberry . . . . . . . . . . . . . . . . . . 0438730203RP

Remote Control20. ...................3000370500RP

Remote Control Receiver21. . . . . . . . . . . . 3000380200RP

6 www.dimplex.com

WIRING DIAGRAM

LIGHT BULB REPLACEMENT

CAUTION: If unit was operating prior to servicing allow

at least 5 minutes for lights to cool off to avoid accidental

burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Light bulbs need to be replaced when you notice a dark

section of the ame or when the clarity and detail of the log

exterior disappears. There are three bulbs under the log

set which generate the ames and embers.

HELPFUL HINTS: It is a good idea to replace all light bulbs

at one time if they are close to the end of their rated life.

Group replacement will reduce the number of times you

need to open the unit to replace light bulbs.

UPPER LIGHT BULB REPLACEMENT

UPPER LIGHT BULB REQUIREMENTS: Quantity of 1

clear chandelier or candelabra bulbs with an E-12 (small)

socket base, 7 watt rating.

Open door by pulling the handle.1.

Locate the upper bulb bracket.2.

Bend light retainer bracket down.3.

Locate and remove the light bulb.4.

Insert new bulb.5.

Bend light retainer bracket back into its original posi-6.

tion.

Close the door.7.

LOWER LIGHT BULB REPLACEMENT

LOWER LIGHT BULB REQUIREMENTS: Quantity of 2

clear chandelier or candelabra bulbs with an E-12 (small)

socket base, 60 watt rating.

Open door by pulling the handle.1.

Remove the 2 screws from the logset grate located in2.

front of the emberbed and remove the grate from the

unit.

Remove the logset from the unit by pulling forward and3.

lifting out.

Locate and examine the bulbs to determine which4.

bulb(s) required replacement.

Locate and remove the light bulb(s).5.

Insert new bulb(s).6.

Install the logset into the unit, and re-install the logset7.

grate.

Close the door.8.

FLAME ROD REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Open door by pulling the handle.1.

Remove the 2 screws from the logset grate located in2.

Figure 3

Figure 4

Figure 5

8 www.dimplex.com

front of the emberbed and remove the grate from the

unit.

Remove the logset from the unit by pulling forward and3.

lifting out.

Remove the reector rod from the ame motor by pull-4.

ing the end of the rod to the left and carefully remove

ame rod from rubber sleeve.

Reassemble in the reverse order as above.5.

FLICKER MOTOR REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Remove the thermostat knob.1.

Gently place stove on it’s back on a at surface.2.

Remove the heater cover retaining screws located on3.

the bottom of the stove and lower heater/light assembly

onto the oor.

Remove the reector rod and motor assembly by 4.

removing the screws on the front and rear of the heater

cover.

Remove the heater retaining screws form the bottom of5.

the heater cover.

Disconnect the wiring clips and connections noting their6.

original locations.

Reassemble in the reverse order as above.7.

REMOTE CONTROL RECEIVER

REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Open door by pulling the handles.1.

Loosen the 2 retainers on the inner sides of the unit by2.

turning counter clockwise.

Remove 4 screws that secure the top on the rear of the3.

unit.

Lift the top off of the unit. Carefully remove the partially4.

reective glass and store in a safe place to prevent

damage.

Locate the remote control receiver on the wall of the5.

unit.

Remove wiring connections from the receiver noting6.

their original locations.

From inside the unit, break off the 4 mounting studs7.

by grasping with pliers and twisting on the protruding

part of the stud, push the remainder of the studs out

through the top panel.

!NOTE: New mounting studs are supplied with the re-

placement remote control receiver.

Reassemble in the reverse order as above.8.

CONTROLS REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

Figure 6

Figure 7

to persons.

Open door by pulling the handles.1.

Loosen the 2 retainers on the inner sides of the unit by2.

turning counter clockwise.

Remove 4 screws that secure the top on the rear of the3.

unit.

Lift the top off of the unit. Carefully remove the partially4.

reective glass and store in a safe place to prevent

damage.

SWITCHES

Locate the switches on the back wall of the unit.5.

Remove wiring connections from the switches noting6.

their original locations.

Squeeze the tabs on the top and bottom of the switch7.

and push out through the back of the unit.

THERMOSTAT

Locate the thermostat on the back wall of the unit.8.

Remove the wiring from the thermostat noting their9.

original locations.

Remove the thermostat knob and 2 mounting screws.10.

Connect all of the wiring connections in their original11.

locations.

Reassemble in the reverse order as above.12.

POWER CORD REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Gently place stove on it’s back on a at surface.1.

Remove the heater cover retaining screws located on2.

the bottom of the stove and lower heater/light assembly

onto the oor.

Remove the reector rod and motor assembly by 3.

removing the screws on the front and rear of the heater

cover.

Locate and disconnect the power cord wiring connec-4.

tions from the heater and 3-Position switch noting their

original locations.

With needle nose pliers, grasp the power cord strain re-5.

lief grommet from inside the rear panel and push while

twisting to remove.

Pull the power cord out through the hole in the rear6.

cover.

Install the new power cord through the hole in the rear7.

cover by placing the strain relief over the cord, hold the

strain relief with pliers and slide into mounting hole.

Connect all of the wiring connections in their original8.

locations.

Reassemble in the reverse order as above.9.

Figure 8

Figure 9

10 www.dimplex.com

HEATER ASSEMBLY REPLACEMENT

WARNING: If the stove was operating prior to servic-

ing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Gently place stove on it’s back on a at surface.1.

Remove the heater cover retaining screws located on2.

the bottom of the stove and lower heater/light assembly

onto the oor.

Remove the reector rod and motor assembly by 3.

removing the screws on the front and rear of the heater

cover.

Disconnect the heater wiring connections from the4.

heater noting their original locations.

Remove the 4 heater mounting screws and remove the5.

heater from the unit.

Reassemble in the reverse order as above.6.

Other manuals for DS5629

Table of contents

Other Dimplex Stove manuals

Dimplex

Dimplex EOS-2006 User manual

Dimplex

Dimplex DS5629 User manual

Dimplex

Dimplex LVT20-AU User manual

Dimplex

Dimplex DCS19W User manual

Dimplex

Dimplex Burgate User manual

Dimplex

Dimplex ELECTRALOG CS4416 User manual

Dimplex

Dimplex ELECTRIC STOVE User manual

Dimplex

Dimplex Tango User manual

Dimplex

Dimplex MCFSTV12AU User manual

Dimplex

Dimplex DS4411 User manual

Dimplex

Dimplex CASSINGTON EN60555-2 User manual

Dimplex

Dimplex Optiflame Electric Fireplace Instruction Manual

Dimplex

Dimplex ELECTRALOG CS1205 User manual

Dimplex

Dimplex DS7420 User manual

Dimplex

Dimplex DS5629 User manual

Dimplex

Dimplex CDS8515 User manual

Dimplex

Dimplex DS5598 User manual

Dimplex

Dimplex Optiflame 3D Laverton LVT20 Instruction Manual

Dimplex

Dimplex Rectory User manual

Dimplex

Dimplex LEE User manual

Dimplex

Dimplex Opti-V 360 User manual

Dimplex

Dimplex Mirage MIR40 User manual

Dimplex

Dimplex BAR20-AU User manual

Dimplex

Dimplex Westcott 5 User manual

Popular Stove manuals by other brands

Arada

Arada Cassette Stove installation guide

Parmco

Parmco FS 600 Installation and operating instructions

MCZ

MCZ SUITE AIR 10 M2 installation guide

HearthStone

HearthStone Stowe DV 8321 Owner's manual & installation guide

Cattara

Cattara FAMILY manual

Stanley

Stanley Argon F500 OVAL Installation and operating instructions

Avalon

Avalon B-VENT instructions

Nordpeis

Nordpeis Vega user manual

Exquisit

Exquisit EKC601-5 Instructions for use and installation

Stanley

Stanley Oisin Oil MK II Installation and operation instruction

Thermocet

Thermocet Brookfield S/CC Operating and installation instructions

HASE

HASE delhi operating instructions

Vermont Castings

Vermont Castings Intrepid 2 User instructions

Italiana Camini

Italiana Camini CLASSICA Installation, use and maintenance

Avalon

Avalon Vashon Avanti DVS FS manual

Spartherm

Spartherm ambiente a1 Installation and operating manual

Warmlite

Warmlite WL46040 manual

Regency

Regency Ultimate U39E Series Owners & installation manual