Digital Security Controls GS3060 User manual

GS3060

GSM-GPRS INTERFACE

WARNING: This manual contains information on limitations regarding product use and

function and information on the limitations as to liability of the manufacturer.

INSTALLATION

MANUAL

Table of Contents

INTRODUCTION .............................................................................................. 1

Features .......................................................................................................... 1

Technical Specifications ................................................................................. 1

Ratings ........................................................................................................... 1

Description ..................................................................................................... 2

IDENTIFICATION OF PARTS .......................................................................... 3

INSTALLING THE GS3060............................................................................... 4

CONNECTING THE GS3060 ........................................................................... 5

STATUS LEDS ................................................................................................. 5

OPERATING PRINCIPLES .............................................................................. 6

Simulated Land Line Mode ............................................................................. 6

PTM (Panel Transmission Monitoring) ............................................................. 6

GPRS Sequence ............................................................................................. 7

Inputs .............................................................................................................. 7

Contact ID Mode ............................................................................................ 7

Outputs ........................................................................................................... 8

Activating the Outputs .................................................................................... 8

Contact ID....................................................................................................... 8

"C-24 REMOTE" PROGRAMMING .................................................................. 8

GS3060 WIRING DIAGRAMS .......................................................................... 9

INTRODUCTION

The GS3060 is a backup wireless communicator that sends alarm system information to a System

III or System II receiver through a GSM/GPRS wireless network. For use with listed compatible

control units as indicated in the control unit manufacturer's installation instructions.

Features

• Compatible with any listed panel that supports 4 or 10-digit Contact ID

• Simulates land line

• Switches automatically to GSM network in the event land line trouble (line down)

• GSM Signal Indicator

• 4 programmable outputs

• Houses 12V - 1.2 Ah battery

• Case Tamper Output

• Land-line Overvoltage Protection

• Dual-Band GSM Radio

• 4 Programmable Inputs

• GPRS/Internet communication with Sur-Gard System III / II

• PTM Feature 4 phone numbers programmable for Contact ID Dialer

Technical Specifications

The input voltage to the GS3060

can be drawn from the Control Panel or provided by an external UL

Listed power supply rated for the application (external power-limited source).

Ratings

Power Supply RatingsPower Supply Ratings

Power Supply Ratings

Input Voltage: ............................................................................................ 9 - 14VDC (13.8VDC typical)

Current: .............................. 120mA* (JP3 - OFF and internal battery required) or 500mA* (JP3 ON)

* Plus any current drawn from the GS3060 AUX+ terminal

Battery: ......................................................................... sealed, rechargeable type, rated 12V/1.2Ah

Recharging current: ................................................................................................................... 50mA

CurCur

Currr

rent consumptionent consumption

ent consumptionent consumption

ent consumption

Standby current: ...................................................................................................................... 120mA

Alarm (Transmitting) current: ................................................................................................... 450mA

PGM outputs: ....................................................................................... 4, open collector, rated 50mA

Operating frequency: ................................................................................................... 850/1900MHz

Antenna Gain: ........................................................................................................................... 2.0dBi

EnvirEnvir

Environmental specificationsonmental specifications

onmental specificationsonmental specifications

onmental specifications

Operating temperature: .................................................................................. 0°C-49°C (32°F-120°F)

Humidity: ................................................................................. 93%RH Maximum (Non-Condensing)

Mechanical specificationsMechanical specifications

Mechanical specifications

Metal enclosure, painted; dimensions: ...................... 138mm x 224mm x 55mm / 5.4” x 8.8” x 2.2”

Weight (without battery): ................................................................................................. 900g / 3.2 oz

Internal Event Buffer (communications): ................................................... 256 Events (not viewable)

Maximum loop resistance of line between the device connected in series on T1/R1: ........... 1Kohm

This equipment GS3060 is fixed and shall be installed by Service Persons only (Service Person is defined as a person

having the appropriate technical training and experience necessary to be aware of hazards to which that person may

be exposed in performing a task and of measures to minimize the risks to that person or other persons). It shall be

installed and used within an environment that provides the pollution degree max 2, over voltages category II, in non-

hazardous, indoor locations only. This manual shall be used with the Installation Manual of the alarm control panel.

All instructions specified within that manual must be observed.

Description

This GS3060 manages transmissions to a central station and can simulate the land line in the event

of trouble (land line down) or even substitute the land line completely in areas where the GSM

service is provided and a land line is not available.

The GS3060 has the capability of communicating alarm signals via the GPRS data network. The

capability enables a fast reliable path to central stations equipped with a Sur-Gard System III or

System II receiver. By connecting a GS3060 to a control panel's standard PSTN interface, telephone

based Contact ID signals are decoded and seamlessly routed through the GPRS network to any of the

compatible receiver options. When configured accordingly, the GS3060, upon line failure, instead of

using GPRS, can also connect the call on the GSM voice channels call based on the panel dialed

number.

The performance of the GS3060 depends greatly on GSM Network coverage, therefore, it should

not be mounted without first performing placement tests to determine the best location for reception

(minimum one green LED is ON). Optional antenna kits are available.

The GS3060 requires enrollment with CONNECT 24 to operate. Dealer application forms and

additional information on the CONNECT 24 Voice Response Unit (VRU) and web user-interface

can be found at www.connect24.com or at the following telephone numbers:

USA 1-888-251-7458USA 1-888-251-7458

USA 1-888-251-7458 CANADA 1-888-955-5583CANADA 1-888-955-5583

CANADA 1-888-955-5583CANADA 1-888-955-5583

CANADA 1-888-955-5583

For UL Residential Fire and Burglary installations, the GS3060 is listed as a primary (sole)

communication means or as a back-up when used in conjunction with a POTS line (dialler).

For UL Commercial Burglary installations, the GS3060 is listed for supplementary (back-up) use in

conjunction with a POTS line (dialler).

For ULC Commercial Fire Monitoring installations the GS3060 is listed as a passive communication

system when used in conjunction with a POTS line (dialler).

For ULC Commercial Burglary installations the GS3060 is listed as a passive communication system

with communication line security level P2 when used in conjunction with a POTS line (dialler).

For ULC Residential Fire and Burglary installations the GS3060 is listed as a primary (sole)

communication means or as a back-up when used in conjunction with a POTS line (dialler).

IDENTIFICATION OF PARTS

The numbers in square brackets [[

[[

[ ]]

]]

] in this manual refer to the main parts of the GS3060 (see Fig.1

below) described in this section.

LE LI

O2 O3 O4

+OC

L1 L2 L3 L4 +12V-

LOCK

OPEN

5 18 3

12 13

TAMPER

PGM3

PGM2

19 20

+ 12V -

AUX+

Z2 17

COM

PGM4

PGM1

COM

T1 5

TIP 3

RNG

JP3

tie wrap

OFF ON

All circuits are classified for UL installations as Power Limited/Class II Power Limited except for the bat-

tery leads which are not power limited. Do not route any wiring over circuit boards. Maintain at least 1”

(25.4mm) separation. A minimum 1/4” (6.4mm) separation must be maintained at all points between

Power Limited wiring and all other Non-Power Limited wiring. Route wires as indicated in the diagram.

GS3060

PARTS

Metal Casing

GSM Antenna

GSM Antenna Mounting Hardware

Anchor Screw Holes (3mm)

Connector for GSM Antenna

SIM Card

Status LEDs (see page 5)

JP3 Current Limitation Jumper (refer to ratings section)

Programming Jumper (Do not short these pins)

RS-232 Connector

Tamper Switch

Terminal Blocks

Battery Leads

Cable Entry

Earth Ground Wire

12V-1.2Ah Battery

GSM Radio Module

SIM Card Holder

Figure 1 - Parts

INSTALLING THE GS3060

CONNECT 24 Enrollment Information

Only authorized dealers can enroll a GS3060 with CONNECT 24. Dealer application forms and

additional information on the CONNECT 24 Voice Response Unit can be found at the CONNECT 24

web site wwwwww

wwwwww

www.connect24.com.connect24.com

.connect24.com.connect24.com

.connect24.com. Please contact CONNECT 24 at the number below for assistance:

USA 1-888-251-7458USA 1-888-251-7458

USA 1-888-251-7458 CANADA 1-888-955-5583CANADA 1-888-955-5583

CANADA 1-888-955-5583CANADA 1-888-955-5583

CANADA 1-888-955-5583

NOTE: Steps 1 and 2 should be completed before powering the GS3060 unit.

STEP 1 - Activate Your SIM Card

Your SIM card must be activated with Connect 24 prior to use. Please call the Voice Response

Unit (VRU) at least 24 hours prior to installation at 1-866-910-3865.

STEP 2 - Initialize the GS3060 with Connect 24

Call the VRU at the toll-free number. Follow the voice prompts and enter in your profile number,

installer ID number, installer PIN number and central station number. Ensure all information is available

before calling the VRU. All this information can be found in your VRU Enrollment Package.

STEP 3 - Determine Best Signal Location

1. Remove the screw and the front cover [1].

2. Fit the antenna [2] (ensure that the bolt [3] is fastened tightly).

3. Using the connector [5], connect the GSM Module [17]. Ensure the connector is secure.

NOTE: Before inserting or removing the SIM card, please ensure the unit is powered down.

4. Power up the GS3060 and check signal strength.

• Connect battery to the RED and BLK battery leads.

• Connect DC Power source to +/- 12V terminals.

• Allow unit to power up

• The green LEDs will indicate the signal strength. The bottom green LED must be ON for the

location to be acceptable. Please refer to the “Status LEDs” section for more information.

5. Power down the GS3060 by removing the DC power source and battery leads.

STEP 4 - Connect the GS3060

1. Using the cabinet, mark the 4 screw locations then drill the anchor screw holes.

NOTE: Check for cable conduits and water pipes before drilling.

2. Using anchor screws (not included), mount the cabinet to the wall.

3. Run the cables, then pull them through the cable entry [14] or the knockouts provided.

4. Complete the connections on the terminal board [12].

Ensure power and Telco circuit con-

nections are made only after the cabinet has been secured to the building or structure

and has been connected to the protective earth ground

. Descriptions of the terminals can

be found in the “Connecting the GS3060” section.

5. Using the 4 screws, reattach the front cover [1] securely to the cabinet.

NOTE: Please refer to Figure 2 at the end of this manual for wiring diagram.

CONNECTING THE GS3060

(1) Ear(1) Ear

(1) Earth Grth Gr

th Grth Gr

th Groundound

oundound

ound

This terminal must be connected to the Mains Earth, in order to comply with the Telecommunications

Network Safety Standards (Overvoltage Protection Requirements).

TIP (2) / RNG (3) ExterTIP (2) / RNG (3) Exter

TIP (2) / RNG (3) External telephone linenal telephone line

nal telephone linenal telephone line

nal telephone line

These terminals must be connected directly to the incoming telephone line .

T1 (4) / R1 (5) InterT1 (4) / R1 (5) Inter

T1 (4) / R1 (5) Internal telephone linenal telephone line

nal telephone linenal telephone line

nal telephone line

These terminals must be connected to the TIP and RING of the control panel.

COM(6,14) CommonCOM(6,14) Common

COM(6,14) Common

This terminal is connected internally to Power Ground.

PGM1 (7), PGM2 (8), PGM3 (9), PGM4 (10) PrPGM1 (7), PGM2 (8), PGM3 (9), PGM4 (10) Pr

PGM1 (7), PGM2 (8), PGM3 (9), PGM4 (10) Programmable open-collector outputsogrammable open-collector outputs

ogrammable open-collector outputsogrammable open-collector outputs

ogrammable open-collector outputs

These outputs can be activated by programmed events, refer to “Activating the Outputs” for details.

The maximum current sink of each output must not exceed 50mA.

AUX+ (11) AuxiliarAUX+ (11) Auxiliar

AUX+ (11) Auxiliary 12V Outputy 12V Output

y 12V Outputy 12V Output

y 12V Output

+12V Output, 200mA PTC Protected.

NOTE: CurNOTE: Cur

NOTE: Currr

rent drawn frent drawn fr

ent drawn frent drawn fr

ent drawn from this terom this ter

om this terom this ter

om this terminal is dirminal is dir

minal is dirminal is dir

minal is directly frectly fr

ectly frectly fr

ectly fromom

omom

the power supplythe power supply

the power supply. This needs to be added to the GS3060 cur. This needs to be added to the GS3060 cur

. This needs to be added to the GS3060 cur. This needs to be added to the GS3060 cur

. This needs to be added to the GS3060 currr

rent when deterent when deter

ent when deterent when deter

ent when determining the totalmining the total

mining the totalmining the total

mining the total

draw on the host panel or power supplydraw on the host panel or power supply

draw on the host panel or power supply. Jumper JP3 does not limit the cur. Jumper JP3 does not limit the cur

. Jumper JP3 does not limit the cur. Jumper JP3 does not limit the cur

. Jumper JP3 does not limit the currr

rent available onent available on

ent available onent available on

ent available on

this output.this output.

this output.

Tamper (12-13)amper (12-13)

amper (12-13)amper (12-13)

amper (12-13)

These terminals are connected in series to the Tamper microswitch [1111

1111

11]. They will be closed when

the cabinet is properly closed, and will open when the front cover is removed.

Z1-Z4 (15-16-17-18) PrZ1-Z4 (15-16-17-18) Pr

Z1-Z4 (15-16-17-18) Programmable Inputsogrammable Inputs

ogrammable Inputsogrammable Inputs

ogrammable Inputs

These terminals can be set up to trigger events. Refer to “Inputs” section for details.

12V (19), COM (20) Device Power Supply12V (19), COM (20) Device Power Supply

12V (19), COM (20) Device Power Supply

These terminals must be connected to a rated power supply.

Once the connections are completed, connect the Red and Black wires [1313

1313

13] to a 12V, 1.2Ah battery.

Jumper JP3Jumper JP3

Jumper JP3

JP3 ON -JP3 ON -

JP3 ON - Full power comes from the host panel or external power supply. Supply must be capable

of up to 700mA, the GS3060 battery must NOT be connected.

JP3 OFF - CurJP3 OFF - Cur

JP3 OFF - Currr

rent Limiting Mode.ent Limiting Mode.

ent Limiting Mode.ent Limiting Mode.

ent Limiting Mode. Host panel or external supply provides standby current. Supply

must be capable of 120mA plus any current drawn from AUX+ terminal. GS3060 battery must be

installed for proper operation. The Power Supply must have a minimum voltage of 13.5 to ensure sufficient

battery charge.

NOTE: When disposing of batteries, follow the instructions and and precautions printed on

the batteries, and contact your municipal offices for information on the disposal of used

batteries.

STATUS LEDS

The GS3060 interface has 4 status LEDs.

NOTE: The top two LEDs will blink during the Initializing and Programming phases.

The following section describes the Control panel status LEDs.

RED — This LED is Normally OFF, it will blink in the event of trouble. This LED will switch ON

within 3 minutes in the event of GSM Module [1717

1717

17] trouble, or when the GSM Network is unavailable

(NO SERVICE). If this LED blinks, the following list will indicate the specific trouble based on the

number of blinks, by priority. On power-up, the GS3060 will check for trouble conditions to be

restored in the order listed below. It will indicate the status of the highest priority, unrestored

trouble condition with the corresponding number of flashes of the RED LED.

Once the highest priority trouble condition has been cleared, the next highest priority trouble condition

will be displayed.

1 flash1 flash

1 flash - Battery Trouble

(Battery absent or battery with low voltage output)

2 flashes2 flashes

2 flashes - Radio/SIM Failure

(Battery absent or check SIM Card connection)

3 flashes3 flashes

3 flashes - GSM Network Problem

(SIM not active, poor signal strength, antenna not

connected)

4 flashes4 flashes

4 flashes - Insufficient Signal Strength

(Poor location)

5 flashes5 flashes

5 flashes - Connect 24 Configuration SMS Failure

(Improper VRU programming. Once the

configuration is ready, remove power for 2-3 seconds to allow the unit to restart and request

again.)

6 flashes6 flashes

6 flashes - Receiver Not Available

(Improper VRU programming, receiver absent)

7 flashes7 flashes

7 flashes - Power Supply Trouble

(DC power supply absent)

OfOf

Offf

f - No Troubles

YELLOW

—

This LED will switch ONON

ONON

ON when the interface switches to the GSM Network (due to land

line trouble). This LED can also blink quickly once (GPRS TX) or twice (GPRS RX).

GREEN (Top)

—

When this LED is ONON

ONON

ON, the reception is optimal. This LED will switch ON only

when the other GREEN LED is ON.

GREEN (Bottom)(Bottom)

(Bottom)(Bottom)

(Bottom) — If this LED is OFFOFF

OFFOFF

OFF and the RED LED is ON, the GSM Network service is

unavailable (NO SER(NO SER

(NO SER(NO SER

(NO SERVICE)VICE)

VICE)VICE)

VICE). This LED will BlinkBlink

BlinkBlink

Blink when the GSM Network reception is bad. If this

LED is ONON

ONON

ON, the GS3060GS3060

GS3060GS3060

GS3060 will be able to communicate to the GSM network.

OPERATING PRINCIPLES

Simulated Land Line Mode

The simulated land line provides the alarm control panel (with dialler interface) with a backup line in

the event of PSTN line trouble. If the voltage on the land line terminals (TIP/RNGTIP/RNG

TIP/RNGTIP/RNG

TIP/RNG) drops below 4V

for a period of between 10 to 45 seconds (depending on the device connected to the T1/R1T1/R1

T1/R1T1/R1

T1/R1

terminals), the GS3060 will switch the connected telephone device to the GSM Network for

approximately 30 to 40 seconds. At the end of this interval, it will check the land line:

•if the land line has been rif the land line has been r

if the land line has been rif the land line has been r

if the land line has been restorestor

estorestor

estoreded

eded

ed, it will switch the connected device back to the land line;

•

if the land line is still downif the land line is still down

if the land line is still down, it will continue to simulate the land line until it is restored. The

GS3060 will not switch during ongoing calls

NOTE:When the land line is down, the GS3060 will provide a dial tone to any device connected

to T1 and R1, including any telephones on the premises. However, the premise phones will not

be able to dial out over the GS3060.

PTM (Panel Transmission Monitoring)

The GS3060 can also monitor the panel’s attempt to communicate. If it determines the panel is

having difficulty it will switch the line to the GSM network. This feature is only active when the

GS3060 is configured as a backup communicator. This feature is in addition to the regular line

voltage detection.

The GS3060 will monitor the phone line for four consecutive failed attempts within a 12 minute

window. A failed attempt is considered when line seizure occurs with dialing, but no Contact ID

kiss-off is detected from the receiver.

Once this condition is met the GS3060 will connect the panel to the GSM network to communicate

the events. Once the GS3060 switches the line it will stay in this mode until the panel hangs up. On

the next event the GS3060 will restart the error detection sequence before switching.

The GS3060 will perform this sequence on ANY phone number that is detected on the line. Specific

central station phone numbers can be programmed into the GS3060 if desired. Up to four, 20-digit

numbers can be added to your installer profile at Connect 24. If programmed, the GS3060 will only

look for Contact ID kiss-off after these numbers are dialed. A TLM trouble (PGM output activation

and/or reporting code if applicable) will also be activated and/or transmitted when the PTM is

activated. The restoral will be sent at the end of the call.

GPRS Sequence

•When alarm is triggered, the Control Panel goes off-hook

•The GS3060 will assert dial tone

•Control Panel dials the number of the central station. Ensure the alarm panel inserts a minimum 1-

second pause, or has dial tone search enabled before dialing the number

•The GS3060 detects the DTMF dialing and stops dial tone

NOTE: The GS3060 is unable to decode pulse dialing.

•The GS3060 will send the required Contact ID dual tone handshake to the panel

•After receiving the handshake, panel transmits alarm message in Contact ID format

•The GS3060 decodes and transforms Contact ID digits into the IP packet and sends it to the Central

Station Receiver over the GPRS network

•The receiver acknowledges the alarm and sends command to the GS3060 to generate the

corresponding 1400Hz kiss-off signal for 800ms minimum

•After the GS3060 generates kiss-off, the panel goes on-hook if no more alarms need to be sent,

or it can send the next alarm

Inputs

The GS3060 has 4 inputs that can be used to trigger specific communications. These events will

transmit using Contact ID format with Inputs 1-4 reporting as [991] to [994] respectively. Default

settings are:

INPUT 1- FIRE INPUT 3 - BURGLARY

INPUT 2 - PANIC ALARM INPUT 4 - SYSTEM TROUBLE

These inputs are normally open and will activate when a short condition is detected between the

terminal and the COM. Refer to the GS3060 Wiring Diagram (Figure 2) at the back of this manual.

NOTE: These inputs communicate using Contact ID format.

NOTE: For UL/ULC installations, connections between alarm panel outputs and GS3060 inputs

shall be run in mechanical protective conduits. To reduce interference with the antenna, it is

recommended that the metal conduit is not connected to the knock-outs on the top of the

cabinet.

Table of contents

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual