Digital Projection Titan Super Quad User manual

Rev F November 2012

USER GUIDES

INSTALLATION AND QUICK-START GUIDE

CONNECTION GUIDE

OPERATING GUIDE

REFERENCE GUIDE

Titan 800 Series

High Brightness Digital Video Projector

Titan Super Quad Series

Titan Quad 2000 Series

Titan Quad Series

112-671F

Digital Projection Titan Quad & Titan 800 Series

Rev F November 2012

About These Guides

Please keep these Guides handy for future reference.

A serial number is located on the back of the projector. Record it here:

Symbols used in these Guides

Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely

followed.

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless

the instructions are closely followed.

NOTE: this symbol indicates that there is some important information that you should read.

Product revision

Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features

without prior notice.

Legal notice

Trademarks and trade names mentioned in this document remain the property of their respective owners.

Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.

Notes

Rev F November 2012

INSTALLATION AND QUICK-START GUIDE

Titan 800 Series

High Brightness Digital Video Projector

Titan Super Quad Series

Titan Quad 2000 Series

Titan Quad Series

Digital Projection Titan Quad, & Titan 800 Series CONTENTS Installation and Quick-Start Guide

Rev F November 2012

CONTENTS

What’s In The Box? ..............................................................................Inst 1

Getting to Know the Projector.....................................................Inst 2

Front and rear views ..............................................................................Inst 2

Remote control.......................................................................................Inst 2

Control panel indicators........................................................................Inst 3

Connection panel indicators.................................................................Inst 3

Positioning The Screen And Projector...................................Inst 4

Chassis adjustment ...............................................................................Inst 4

Fitting and adjusting the optional Rigging Frame ..............................Inst 4

Fitting The Lens .....................................................................................Inst 5

Operating The Projector ..................................................................Inst 6

Switching the projector on....................................................................Inst 6

Selecting an input signal or test pattern..............................................Inst 6

Input signal.....................................................................................Inst 6

Test pattern ....................................................................................Inst 6

Adjusting the lens ..................................................................................Inst 7

Zoom..............................................................................................Inst 7

Focus .............................................................................................Inst 7

Shift................................................................................................Inst 7

Adjusting the image...............................................................................Inst 7

Orientation and On-Screen Display settings..................................Inst 7

Keystone ........................................................................................Inst 7

Picture............................................................................................Inst 7

Switching the projector off....................................................................Inst 8

Digital Projection Titan Quad, & Titan 800 Series WHAT’S IN THE BOX? Installation and Quick-Start Guide

Inst 1

Rev F November 2012

What’s In The Box? Notes

Make sure your box contains

everything listed. If any pieces are

missing, contact your dealer.

You should save the original box

and packing materials, in case you

ever need to ship your projector.

The projector is shipped without a

lens.

Only one power cable - dependent

on the destination territory - will be

supplied with the projector.

Remote control

(105-023)

4x AAA batteries

Power cable, United Kingdom

(102-180 for Titan 800, 112-000

for Quad)

User Guides on CD

(112-659)

Important Information (112-658)

Power cable, Europe

(102-163 for Titan 800, 112-001 for Quad)

Power cable, North America

(102-165 for Titan 800, 112-002 for Quad)

Projector

Remote cable

(102-162)

Digital Projection Titan Quad, & Titan 800 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide

Inst 2

Rev F November 2012

Getting to Know the Projector

Front and rear views Remote control

Transmit

indicator

40°

Infra-red

reception

Notes

The projector uses the standard

Digital Projection infra-red remote

control.

Only the controls shown highlighted

are used on this projector.

For full details of how to use the

controls and the menu system, see

the Operating Guide.

The Side Connection Panel is

available on 3D models only.

Lens

Control

panel Side

Connection

panel

Front

infra-red

window

Mains

input

Rear

infra-red

window

(on

connection

panel)

Air lters

(behind panel)

Adjustable

feet

Air

inlets

Air

outlets

Remote

control

backlight

On/Off

Rear

Connection

panel

Digital Projection Titan Quad, & Titan 800 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide

Inst 3

Rev F November 2012

Control panel indicators

The indicators on the control panel are as follows:

Power off = NO POWER

green = normal RUNNING mode amber = STANDBY mode

Shutter amber = CLOSED green = OPEN

Connection panel indicators

The indicators on the rear connection panel are as follows:

All on = Power-On Self Test

Lamps 1-4 off = OFF

green = ON (100%) amber = (80 - 99%)

ashing green = WARM-UP ashing amber = COOL-DOWN

red (projector in standby) = Lamp Comms Error (call service)

red (projector on) = Ballast Comms Error (call service)

ashing red (projector in standby) = Lamp Error on previous operation

ashing red (projector on) = Lamp / Interlock Error

Error ashing = Fan / System Error steady = Voltage Error

IR blue ash = Remote control command received

Inputs The indicators next to the input connectors on both panels are as follows:

off = not selected

green = input selected, signal detected, and in range

ashing green = input selected, but signal not detected or out of range

Power Shutter

Notes

Only the controls shown highlighted

are used on this projector.

For full details of how to use the

controls and the menu system, see

the Operating Guide.

For more information about

the connection panels, see the

Connection Guide.

Control Panel

Error

Lamps

3 4

1 2

Side Connection Panel

Rear Connection Panel

Digital Projection Titan Quad, & Titan 800 Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide

Inst 4

Rev F November 2012

Positioning The Screen And Projector

• Install the screen, ensuring that it is in the best position for viewing by your audience.

• Position the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen.

Chassis adjustment

• If the projector is to be operated from a at surface such as a projector table, then adjustment of projector level should be made by turning

the four feet under the chassis. Set the adjustable feet so that the projector is level, and perpendicular to the screen.

Fitting and adjusting the optional Rigging Frame

• Remove the four adjustable feet.

• Secure the rigging frame to the projector, as shown below, making sure that the cable

attachments are at the top. Three screws secure each of the adjuster brackets to a corner

handle.

• To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking

care to turn both adjusters by the same amount.

• To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care

to turn both adjusters by the same amount.

• To adjust the yaw, turn the single horizontal adjuster at the front.

Fixing

screws

Yaw

Horizontal

adjuster

Vertical

adjusters

Frame

couplings

Pitch Roll

Notes

Always allow the projector

to cool for 5 minutes before

disconnecting the power or

moving the projector.

Ensure that there is at least

30cm (12in) of space between the

ventilation outlets and any wall,

and 10cm (4in) on all other sides.

Do not stack more than 3

projectors.

Do not place heavy objects on top

of the projector chassis. Only the

chassis corners and the rigging

frame are capable of withstanding

the weight of another projector.

Do not place the projector with its

front panel down on a surface, as

this may damage the lens or the

lens release lever.

Backup safety chains or wires

should always be used with

ceiling mount installations.

Do not tilt the projector more

than ±12° in either direction, in

desktop or ceiling mode, when in

use, as this may cause serious

lamp failure, damage the lamp

module and cause extra cost on

replacement.

±12°±12°

±12°±12° Ceiling

Desktop

Digital Projection Titan Quad, & Titan 800 Series FITTING THE LENS Installation and Quick-Start Guide

Inst 5

Rev F November 2012

Fitting The Lens

• Turn the lens release lever clockwise so

that it is pointing upwards, to open the

lock fully.

• Remove the rear lens cap from the lens.

• Insert the lens into the lens aperture,

making sure that the plug on the zoom

drive mechanism lines up with the socket

on the front of the projector, then push

the lens in rmly as far as it will go.

Lens

release

lever

Notes

Always allow the lamp to cool for

5 minutes before:

- disconnecting the power

- moving the projector

The lens release lever should

always be set to the locked

position to prevent the lens from

falling out.

Do not place the projector with its

front panel down on a surface, as

this may damage the lens or the

lens release lever.

• Turn the lens release lever anti-clockwise

to the mid-position.

• The lens can now be pushed in further.

Push the lens in rmly as far as it will go.

• Turn the lens release lever fully

anti-clockwise so that it is pointing

downwards, to close the lock fully.

Digital Projection Titan Quad, & Titan 800 Series OPERATING THE PROJECTOR Installation and Quick-Start Guide

Inst 6

Rev F November 2012

Operating The Projector

Switching the projector on

• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.

• Wait until the self-test has completed and the standby indicator on the projector control panel shows amber. The lamp will be off and the

projector will be in STANDBY mode.

• Press on the remote control or the control panel and hold for 3 seconds, to switch the projector ON. The power indicator on the

control panel will show green, the lamp will light and the shutter will open.

Selecting an input signal or test pattern

Input signal

• Connect an image source to the projector. The signal should be automatically detected by the projector,

and should be displayed within two or three seconds.

If more than one signal is connected, then select the image you want to display:

• Press one of the Input buttons, to on the remote control, or

• Open the On-screen display (OSD) by pressing .

• Select an input signal from the Input Selection menu, using the and buttons.

Test pattern

If you have no image source connected to the projector, then you can display a test pattern instead:

• Open the OSD by pressing .

• Select Test Pattern from the Input Selection menu, using the and buttons.

• Select a pattern from the Test Pattern menu, using the and buttons.

• Close the OSD by pressing again.

Notes

For full details of how to use the

controls and the menu system, see

the Operating Guide.

Other manuals for Titan Super Quad

This manual suits for next models

Table of contents

Other Digital Projection Projector manuals

Digital Projection

Digital Projection E-Vision Series User manual

Digital Projection

Digital Projection TITAN sx+-500 User manual

Digital Projection

Digital Projection TITAN WUXGA 3D User manual

Digital Projection

Digital Projection HL12000HD User manual

Digital Projection

Digital Projection M-Vision Cine 320 Series User manual

Digital Projection

Digital Projection FUSION User manual

Digital Projection

Digital Projection 4500 WUXGA User manual

Digital Projection

Digital Projection Titan 930 User manual

Digital Projection

Digital Projection Titan 930 User manual

Digital Projection

Digital Projection HIGHlite Laser II 3D Series User manual

Digital Projection

Digital Projection M-Vision LED 1000 1080p User manual

Digital Projection

Digital Projection E-Vision Laser 5000 Series User manual

Digital Projection

Digital Projection E-Vision WUXGA-8000 User manual

Digital Projection

Digital Projection TITAN sx+ 3D User manual

Digital Projection

Digital Projection M-Vision Cine 400 3D series User manual

Digital Projection

Digital Projection TITAN sx+ Dual 3D Ultra Contrast User manual

Digital Projection

Digital Projection LIGHTNING 30-1080p User manual

Digital Projection

Digital Projection HIGHlite Laser 3D Series User manual

Digital Projection

Digital Projection LIGHTNING 30sx+c User manual

Digital Projection

Digital Projection Titan 1080p-500 Operating manual

Digital Projection

Digital Projection Titan 1080p-500 User manual

Digital Projection

Digital Projection SHOWlite 6000gv User manual

Digital Projection

Digital Projection TITAN SX+ 500 User manual

Digital Projection

Digital Projection 7000 Series User manual

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual