6. Pressing C button once any time during this TIMER setting sequence will complete the setting and the timer is ready to start upon pressing the A button.
7. Press A to start countdown with the “1 ” at the top right corner blinking and the timer setting counting down. When the 1st timer approaches zero, the timer
gives 4 beeps and the 2nd timer starts counting down immediately. When the 2nd timer approaches zero, it gives 2 beeps and the 4 digit counter at the
lowest row advances by 1 automatically.
8. At any time during countdown pressing A will stop counting.
If only the 1st timer is set the timer is used as an ordinary countdown timer and will give 5 times 4 beeps when the set time is up. The 4 digit counter also
advances by 1 automatically when the timer reaches zero.
STROKE / FREQUENCE BASE 3 ;
1. Press the button C to go into « chronograph mode ».
2. Press B during few seconds to go into « speed mode » (in fig.14).
3. Scroll with the button B.
4. Select the numbers with the button A. The distance has to be set up on « 180 » (0180.000) and the time unit on « seconds » (SEC).
Then, press Cto confirm.
5. Start the « chronograph mode » with the button A. After the third stroke only, press A again. The line in the middle indicates the number of strokes per
minute.
DATA STORED RECALL:
1. Press D to recall data stored. The display which we call the RACE RECORD is as shown in Fig. 8.
2. The display shows the date in which the race was recorded and MCH-001 (MSP for SPEED mode) stands for the first race
3. Recorded in LAP/SPLIT mode at that date.
4. Press D again to recall the 1st LAP data, as shown in Fig.9.
5. Press D to recall the 2nd LAP data.
6. Press D again shows the stopped time
7. Press D again to show the average LAP time
8. Press D again to show the Best LAP time.
9. The AVERAGE calculation and BEST record do not take into account the last section of time before STOP. Therefore, in order for the stopwatch to keep
track of the average and best records of all laps, always use the B button until the end of the race.
10. Pressing D again will go to the next race records or return to the 1st race records (if there is no further race).
MEMORY USED UP:
You have the possibility to clear the races one by one, or to clear all. From the chronograph mode (time display must be put to zero), press the D button to
accede to data stored.
1. Clear the races one by one:
Choose the race you want to clear and press B button (race number in the right down corner). Press and hold A button when the stopwatch is displaying the
RACE RECORDS will clear the memories in that race record (when the contents in this race record are cleared the display will show “CLEARED”and
sounds a long beep, if A is released before ED appears. Repeat the operation to clear races one by one.
2. Clear all races:
Press A button during some seconds. « CLEAR », « CLEARED », « ALL CLEAR », « ALL CLEARED » will appear successively. “ALL CLEARED” appears
when all data are cleared. The display comes back to the chronograph mode (fig.2)
When all the memories have been used the 4 digit LAP counter at the top left corner will start blinking to indicate all memories have been used up. All further
LAP memories will not be recorded in the memory unless some memories are cleared as previously indicated. When there is no memory left pressing A to
start a race will sound 3 short beeps.
Do not leave the stopwatch running if not in use as that drains a higher power from the battery.
UPLOAD MODE:
1. In Fig. 20 press D button once will switch to UPLOAD MODE.
2. Pressing A button will UPLOAD ALL recorded memories to computer (if computer is connected). When the stopwatch is in the process of uploading, an
indicator moves from right to left. When upload is complete UPLOAD END is displayed.
3. Press D button to return to PRINT MODE.
4. Pressing B at the UPLOAD ALL mode will go to the UPLOAD RACE mode with display.
5. Pressing A in this mode will only upload the memories in this race.
6. Press B to select particular race to upload.
7. Pressing C any time during this uploading process will stop printing immediately.
8. If the chronograph is not reset (i.e. still running or stopped), it will not be possible to upload and the display will show UPLOAD 0, there will not be any
action upon pressing A or B.
PRINT MODE:
1. Press C button to go to the PRINT ALL mode as shown in Fig.20.
2. Pressing A button will print all recorded memories to the printer (if printer is connected). When the stopwatch is in the process of printing, an indicator
moves from right to left. When printing is complete PRINT END is displayed.
3. Pressing B at the PRINT ALL mode will go to the PRINT RACE mode with display as shown in Fig.21.
4. Pressing A in this mode will only print the memories in this race.
5. Press B to select particular race to print.
6. Pressing C any time during this printing process will stop printing immediately.
7. If the chronograph is not reset (i.e. still running or stopped), it will not be possible to upload and the display will show PRINT 0, there will not be any action
upon pressing A or B.
CARE OF YOUR STOPWATCH:
WATER-RESISTANCE
The stopwatch is designed to withstand accidental contact with water such as splashes or rain, but it, is not designed for use in water. Do not operate the
buttons when the stopwatch is wet.
TEMPERATURE
Do not leave your stopwatch under direct sunlight or in very high temperatures for a long time, or the display may become black. Do not leave your stopwatch
in very low temperature as this may cause a slight time loss or gain and the change of digits becomes slow. In both cases the above conditions will be
corrected when the stopwatch returns to normal temperature.
SHOCKS
Be careful not to drop your stopwatch or hit it against hard surfaces as it may cause mechanical damages.
STATIC ELECTRICITY
The integrated circuit in your stopwatch can be affected by static electricity. If the static electricity is very strong a permanent damage can occur. Be careful of
the screen of the TV set and the wearing of clothing made of synthetic materials in dry weather; in such cases a very strong static electricity can be
generated.
MAGNETISM
Not affected.
CHEMICALS
Do not expose your stopwatch to solvents such as gasoline and alcohol, spray of cosmetics, cleaners, paints etc as they may cause damage to the
stopwatch.
BATTERY CHANGE
When the battery low indicator lights up, battery replacement is necessary.
